Overview
The NXV-CPI (FG2263-03) is a small rack-mountable device which enables
users to connect a Cisco IP phone to a NetLinx master to provide room control
from the phone. The NXV-CPI is installed to the NetLinx Master, and passes
NetLinx control commands to the Master via Ethernet 10/100 cable.
FIG. 1
NXV-CPI (front panel)
Specifications
The following table lists the specifications for the NXV-CPI:
NXV-CPI Specifications
Front Panel
• 4 LED Indicators:
Components:
Power LED (green): Solid on indicates power is on.
Status LED (green): Blinks to indicate that the unit is
communicating with the NetLinx Master.
• Output LED (red): Lights to indicate the device is sending an
XML file to the IP phone or a button press to the NetLinx
master.
• Input LED (yellow): Lights to indicate the device is receiving a
command from the NetLinx master or a button press HTTP
message from the IP phone.
• 1 pushbutton for factory default configuration reset
Rear Panel
1 LAN Port - 10/100 Ethernet with PoE. LEDs show
Connectors:
communication activity, connection status, speeds, and mode
information:
• SPD (speed) - Yellow LED lights On when the connection
speed is 100 Mbps and turns Off when the speed is 10 Mbps.
• L/A (link/activity) - Green LED lights On when the Ethernet
cables are connected and terminated correctly, and blinks
when receiving Ethernet data packets.
Power
PoE powered – no local Power Supply needed
Requirements:
Memory:
• 64 Mbytes of RAM
• 256 Mbytes of FLASH
Dimensions
With feet:
(HWD):
• 1.66" x 5.54" x 4.10" (4.216 cm x 14.07 cm x 10.42 cm)
Without feet:
• 1.52" x 5.54" x 4.10" (3.861 cm x 14.07 cm x 10.42 cm)
Weight:
1.45 lbs. (0.65 kg)
Operating
• Operating Temperature: 32°F - 104°F (0°C - 40°C)
Environment:
• Storage Temperature: 14°F - 158°F (-10°C - 70°C)
• Relative Humidity: 5% to 85% non-condensing
• Intended for indoor use only
Other AMX
• PS-POE-AF PoE Injector (FG423-80)
Equipment:
• AC-DIN-CS3 DIN Rail Mounting Bracket (FG532-01)
• AC-RK Accessory Rack Kit (FG515)
Certifications:
• FCC Class B
• CE
• IEC60950
• RoHS
NXV-CPI
Installation
Note: To avoid any damage to the electronic component, installation must be
performed in an ESD safe environment.
The NXV-CPI is installed to the NetLinx Master, and passes NetLinx control
commands to the Master via Ethernet 10/100 cable, as indicated in FIG. 2.
NXV-CPI
PoE injector
FIG. 2
NXV-CPI Installation
Ethernet 10/100 Base-T RJ-45 Wiring Configuration
The table below describes the pinouts, signals, and pairing for the Ethernet
10/100 Base-T connector and cable.
Ethernet Pinouts and Signals
Pin
Signals
Connections
1
TX +
1 --------- 1
2
TX -
2 --------- 2
3
RX +
3 --------- 3
4
no connection
4 --------- 4
5
no connection
5 --------- 5
6
RX -
6 --------- 6
7
no connection
7 --------- 7
8
no connection
8 --------- 8
FIG. 3 diagrams the RJ-45 pinouts and signals for the Ethernet RJ-45 connector
and cable.
FIG. 3
Straight-Through Wiring
PoE (Power Over Ethernet)
The NXV-CPI uses CAT5/CAT6 wire via the Ethernet port for PoE power. The
maximum power draw for the NXV-CPI is 2.2 watts.
Use the PS-POE-AF Power over Ethernet Injector (FG423-80) to simplify wiring
and installation by eliminating the need for an AC outlet at each point of
installation.
Note: The NXV-CPI can be placed up to approximately 330' (100 meters) from
the nearest PoE Injector.
•
If used with a non PoE-capable Ethernet switch, then an optional
PS-POE-AF Power-over-Ethernet (PoE) power supply is required to
provide power to the NXV-CPI.
•
If the NXV-CPI is used with a PoE-capable Ethernet switch, then no PoE
Injectors are required.
Installation Guide
Control Phone Interface
NetLinx Master
Ethernet 10/100
Ethernet Switch
Ethernet 10/100
To Cisco Call Manager
Pairing
1 --------- 2
White-Orange
Orange
3 --------- 6
White-Green
White-Blue
White-Brown
To Cisco
Phone
Color
Blue
Green
Brown