AMX MyTurn HPA-MYT-RX Quick Start Manual

Overview
The HPA-MYT-TX MyTurn™ Source Selector Button (FG554-21) connects to the end of
a standalone MyTurn-Ready cable (HDMI, Mini-DP, DP, RGB, USB), or one thats installed
in a Retractable Cable Module (RCM). A user presses the button to send their device
content to a conference room display. When pressed, the button wirelessly transmits a
signal to the HPA-MYT-RX MyTurn Source Selector Wireless Receiver (FG554-23) that is
wired to an AMX master controller or an AMX switching device, such as a Solecis SDX or
Enova DVX. When used with a Solecis SDX, simple switching can be implemented with
no NetLinx programming required. Each MyTurn Source Selector Receiver can
accommodate up to 8 MyTurn Source Selector Buttons.
MyTurn Receiver
MyTurn TX Button
FIG. 1 HPA-MYT-TX MYTURN BUTTON (LEFT) AND HPX-MYT-RX MYTURN RECEIVER (RIGHT)
MyTurn Source Selector Buttons and Receivers have the following user features:
MyTurn Source Selector Button
• Push button – activates input at switcher to display device content
MyTurn Receiver
• Select Button – press momentarily to switch ports (indicated by LEDs)
– press and hold to enter "pairing" mode
– press and hold during power up to reset to factory defaults

Product Specifications

HPA-MYT-TX SPECIF ICATIONS
Dimensions • 1.421" x .645" x 0.40" HWD (36mm x 16mm x 10mm)
Power: • Integrated 3VDC coin-cell battery (not replaceable)
• Expected Lifetime: 30K presses or 5/6 years of typical usage
Environment • Operating Temperature: 32° F (0° C) to 122° F (50° C)
• Operating Humidity: 20% to 85% RH
Top Panel: • Push-button
Compatibility: Retractable Cable Module (RCM) Assemblies:
• FG552-32 - HDMI 4K60 RCM with MyTurn-Ready Cable
• FG552-33 - DisplayPort 4K60 RCM with MyTurn-Ready Cable
• FG552-36 - Mini DisplayPort 4K60 RCM with MyTurn-Ready Cable
• FG552-35 - RGB with Stereo RCM with MyTurn-Ready Cable
• FG552-37 - USB 3.0 RCM with MyTurn-Ready Cable
Flat Cable Assemblies:
• FG10-2192-xx - HDMI 4K60 MyTurn-Ready Flat Cable (xx=16 or 32 ft)
• FG10-2193-16 - DisplayPort 4K60 MyTurn-Ready Flat Cable
• FG10-2195-16 - RGB with Auto MyTurn-Ready Flat Cable
• FG10-2196-16 - Mini DisplayPort 4K60 MyTurn-Ready Flat Cable
• FG10-2197-16 - USB MyTurn-Ready Flat Cable
Accessories: • HPX-2BTN-8ACC - 8 button inserts and 8 cable bands kit (optional)
• Quick Start Guide Included
• 2 TX Button mounting clips - one for VGA, one for HDMI/DP/mDP/USB
HPA-MYT-RX SPECIF ICATIONS
Dimensions (HWD) • 3.21" x 2.54" x 0.55" HWD (82.55mm x 69.85mm x 15.24mm)
Enclosure: • Polycarbonate plastic with matte finish
Input Voltage: • 8-15 VDC on the "+12V" input operates LEDs and I/O outputs
to Solecis, NI-Controller or DVX Switcher
• The Rx must receive the 8-15VDC power from a distance of 3
meters or less.
Environment • Operating Temperature: 0° C (32° F) to 50° C (122° F)
• Operating Humidity: 20% to 85% RH
Front Panel: • 8 Yellow LEDs
• 1 Push button for pairing or port selection
Rear Panel: • 1 x 6 Phoenix screw-terminal - I/O 1-4 and Power/Ground
• 1 x 4 Phoenix screw-terminal - I/O 5-8
• 1 Green LED indicates power is applied, and flickers when any
wireless transmission is detected.
Accessories: • Quick Start Guide Included
• 3M Reclosable Fastener strips for mounting the receiver under a
table
• Phoenix Plugs (4 and 6 port)
HPA-MYT-TX/RX
MyTurn Source Selector Solution in a Conference Room
The eight outputs on the rear of the MyTurn Source Selector Receiver connect using
Phoenix connector to the SW inputs on Solecis SDX-510M-DX, or GPIO inputs on NI
Controllers or Enova DVX devices. When the MyTurn Source Selector Button paired with
that I/O port is triggered, the MyTurn Source Selector Receiver activates the AMX
device "SW" input or I/O port, signaling the system to switch the display to that port.
Pairing and port
select button
FIG. 2 MYTURN TO AMX SOLECIS DIGITAL SWITCHER CONNECTION EXAMPLE
Following are examples of two typical MyTurn Source Selector installations.
Solecis SDX-410/510/810 Switchers
The MyTurn Source Selector Receiver connects to the AMX Solecis front AXLINK port
for power and ground as outlined in FIG. 3. Output ports (1 through 8) are wired to the
corresponding Solecis rear "SW" input that has a MyTurn Source Selector Button
equipped cable connected to it. This solution can be implemented without NetLinx
programming since the SW port is directly connected to the Receiver.
FIG. 3 MYTURN SOURCE SELECTOR SW CONNECTION (1 CONNECTION SHOWN)
Note: Only on the SDX-510-DX, set dipswitch #4 in the ON position (Direct Mode). This
will set the external button behavior to be in direct mode by default. Once the
dipswitch is turned ON the SDX-510-DX must be rebooted in order for the setting to
take effect.
Enova DVX Master/NetLinx Integrated Controller
The MyTurn Source Selector Receiver connects to an AMX DVX Master or a NetLinx
Controller using the GPIO interface as outlined in FIG. 4. The GPIO port can deliver
Power and Ground as well as receive switch inputs 1-8.
This solution requires NetLinx programming to correlate a GPIO input button event to
switch to a predetermined port on the DVX.
MyTurn Source Selector Receiver Installation
Refer to the following steps to install the MyTurn Source Select Buttons and Receivers.
Note: 3M Reclosable Fastener strips are provided to attach the receiver under the table.
The adhesive strips require 24 hours dwell time to obtain 90% adhesion before
applying a load or disengaging assemblies (50% bond strength after 20 minutes,
90% after 24 hours.
Note: The MyTurn Source Selector Wireless Receiver must be installed within 10 meters
(32 ft) of the MyTurn Source Selector Buttons. Care must be taken to minimize
metal obstructions to the wireless signal (i.e., equipment racks).
Note: The Rx must receive the 8-15VDC power from a distance of 3 meters or less.
1. Clean surfaces and with alcohol wipes and apply the Velcro strips to the receiver
and table mounting location 24 hours in advance for strong adhesion.
2. Wire the Solecis, DVX, or NX/NI Master Controller using 24 AWG wire in the
Phoenix screw terminals. Ensure Power and Ground are connected as shown
(FIG. 5). Use the AXLINK ports for Power and Ground if connecting to a Solecis as
MyTurn
MyTurn Button
mDP
DP
Solecis SDX
HPX-MYT-RX Receiver Solecis SDX-Front
Status LED
HPX-MYT-TX
Button

QUICK START GUIDE

Source Selector
TM
HDMI
HydraPort
Chassis
MyTurn-Ready Cables
in a HydraPort RCM
Solecis SDX-Rear
MyTurn-Ready
HDMI Cable
Display End
MyTurn-Ready HDMI Cable
Source End