Users 16-30 Arm/Disarm Code Enabling - Ranger 9000E Installation Manual

SELECTING COMMUNICATOR CODES FOR ZONES 17-32
All zones and other reported features are programmed with up to four (4) programming locations. The first three (3) are
used for a 1, 2, or 3, digit communicator code, according to the restraints of the selected communicator format. The
fourth (4th) and last location is used to select if the code is to be sent to phone #1, phone #2, the internal log, activate
listen-in, any combination of these selections, or all four options. The following example will assist you in this selection
process. Factory defaults to a three digit event (alarm) code. NOTE: The first digit will be ignored when using a 3 + 1
Extended, or 4 + 2 format. The first and second digit will be ignored when using a 3 + 1 or 4 + 1 format.
Locations 444-446: Programming The Communicator Code For Zone 17
Locations 444-446 contain the communicator codes to be reported each time zone 17 creates an alarm. Location
444 contains the first digit, location 445 contains the second digit, and location 446 contains the third digit. Always
use the correct number of digits that the selected format allows. Program in the order you wish the receiver to print
the report.
Location 447: Select Phone #1, 2, Internal Log, Or Any Combination For Zone 17
The number in this location will determine where the communicator report for zone 17 will be sent. This number is
derived by adding a "1" for phone #1, a "2" for phone #2, and a "4" for the internal log and an "8" for activation
of Listen-in. If you want this code to be reported to both phone numbers you must program a "3" (1+2) in this
location. If you want this code to be reported to both phone numbers and the internal log you must program a
"7" (1+2+4) in this location. Factory default is "13", which causes zone 17 to report to phone #1, the internal log,
and activate Listen-in, if used.
Location 448-507: Programming The Communicator Code and Selecting Phone Number 1, 2, Internal Log,
Listen-in, or Any Combination For Zones 18-32
Location 508: Reserved
Location 509: Listen-In Time
Program the number of minutes desired for Listen-in at this location (maximum 7 minutes). Factory default is "0".
Location 510: Dial Attempts To Phone #2
This location contains the number of dial attempts to the second phone number for a dual or split report to the
second phone number. This is useful when the second number is a pager. Factory default is "0".
Location 511: Expander Trouble Restore Code
Location 511 contains the Expander Restoral Code. If this location is "0", restorers will not be reported.
Locations 512-571: Programming The Arm/Disarm Code For Users 16-30
Locations 512-571 contain the arm/disarm codes for user numbers 16 thru 30. EACH CODE MUST CONTAIN FOUR
(4) DIGITS. To disable a code, program a "15" as the first digit of the code. This code can be changed in the RUN
mode using the master code (see User's Manual). The factory default for users 16 thru 30 is "15", disabled.
Locations 572-586: Users 16-30 Arm/Disarm Code Enable By Partition
PARTITIONED SYSTEMS
If partitions are utilized, codes may be assigned to a
specific partition by using locations 572-586. This is
done by enabling each individual code (code 16 is
location 572, code 30 is location 586) for each of the
four partitions that code should have access to.
Codes are selected by adding the value for each
partition together and placing that number in the
proper location.
(See Locations 444 - 447)
VALUE
1
2
4
8
32
PARTITIONS
PARTITION 1
PARTITION 2
PARTITION 3
PARTITION 4