How To Use Your Smart-Set™ Slow Cooker; Auto Cook Mode - Crock-Pot Smart-SetTM Owner's Manual

How to Use Your Smart-Set™ Slow Cooker
Figure 3
Lights indicate
slow cooking
mode
Select cooking
temperature-High,
Low, or keep Warm
Cycle through
pre-set meat
options for use with
temperature probe
(Auto Probe Mode)
Figure 4
Temperature
Probe
Notches in
Stoneware for
Temperature
Probe Cord
Temperature
Probe Housing
SCVC600SS-CN.idd.indd 9-10 SCVC600SS-CN.idd.indd 9-10
Lights indicate
cooking
temperature
Program to cook
at two different
temperatures for
chosen periods of
time (Dual Cycle
Mode
Turn the slow
cooker On or Off
Select cooking time from
30 minutes to 20 hours, in
30 minute increments
Temperature
Probe Jack
E6

Auto Cook Mode

h e A u t o C o o k M o d e c o o k s y o u r m e a l b a s e d o n b o t h t e m p e r a t u r e a n d t i m e
s e t t i n g s ; y o u r m e a l i s d o n e w h e n i t h a s r e a c h e d t h e s a f e i n t e r n a l t e m p e r a t u r e
a n d t h e n h a s s i m m e r e d t o r e a c h t h e o p t i m a l t a s t e . h e p r e - s e t m e a t o p t i o n s a n d
d i g i t a l t h e r m o m e t e r e n s u r e p e r f e c t r e s u l t s , r e g a r d l e s s o f t h e s i z e o r c u t o f y o u r
m e a t , a n d t h e S m a r t - S e t ª s l o w c o o k e r a u t o m a t i c a l l y s w i t c h e s t o t h e W A R M
s e t t i n g s o t h a t y o u r m e a l i s a l w a y s w a r m a n d r e a d y t o s e r v e . U s e t h i s m o d e
w h e n t a s t e i s y o u r t o p c o n c e r n , a s i t w a s d e s i g n e d t o p r o d u c e o p t i m a l r e s u l t s
e v e r y t i m e .
1. Place the stoneware into the heating base.
2. Prepare your ingredients and place them into the stoneware.
3. Plug the temperature probe cord into the temperature probe jack on the
heating base. (See Figure 4)
4. Insert the temperature probe into the thickest piece of meat or center of
dish. Attach the lid to the heating base, allowing the temperature probe
cord to set in the notch of the stoneware, under the closed lid. (See Figure 4)
NOTE: If the temperature probe cord is pulled out of the temperature probe
jack while the unit is plugged into an electrical outlet, the slow cooker will
beep and display PROB OUT until the temperature probe cord is plugged
back into the temperature probe jack.
5. Plug the heating base into a standard outlet.
6. Press the AUTO button to cycle through and select BEEF, POUL (poultry),
PRK1 (bone-in pork), PRK2 (boneless pork), CHIL (chili), or STEW.
7. Press the TEMP button to select HIGH (II) or LOW (I).
8. Press the START/STOP ( ) button to start cooking. The upper display
shows the AUTO selection, the lower display shows the internal
temperature of the food, and the corresponding temperature light
illuminates. The lower display will reflect the internal temperature, as it
changes.
9. When the internal temperature of the meat reaches the safe temperature,
the slow cooker beeps once, the upper display shows "SIMR," and the lower
display shows the additional cook time* (see chart on page 17) and then
starts to count down. At this point, the food is simmering until it reaches
its optimal taste.
10. When the cook time expires, the slow cooker beeps twice, and the
temperature shifts to WARM (
and the lower display is off.
). The upper display shows WARM (
E7
8/22/06 4:57:00 PM 8/22/06 4:57:00 PM
)