Conair HTC 30 User Manual page 5

Installation - Piping/Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35
Optional hard piping kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36
Connecting the heat sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37
Hopper Temperature Controller (HTC) as heat source . . . . . 3-37
GasTrac as heat source. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38
Connecting the dryer to the heat source . . . . . . . . . . . . . . . . . . . . 3-39
Connecting the dust collector (optional). . . . . . . . . . . . . . . . . . . . . 3-40
Connecting the cyclone separator (optional) . . . . . . . . . . . . . . . . . 3-41
Installing the Dwyer 641 air velocity transmitter . . . . . . . . . . . . . . 3-42
Installing the level switch (optional). . . . . . . . . . . . . . . . . . . . . . . . 3-44
Adjusting the level sensor (optional) . . . . . . . . . . . . . . . . . . . . . . . 3-45
Installing the process protection RTD sensor. . . . . . . . . . . . . . . . . 3-46
Location of the process material temperature probe (RTD) . . . . . . 3-47
Installing the GasTrac RTD sensor . . . . . . . . . . . . . . . . . . . . . . . . . 3-48
Installing the return air dew point line . . . . . . . . . . . . . . . . . . . . . . 3-49
Installation - Main Power Connections . . . . . . . . . . . . . . . . . . . 3-51
Connecting main power to the dryer . . . . . . . . . . . . . . . . . . . . . . . 3-52
Connecting main power to the HTC
(Models HTC 30, 60, 90 and 120) . . . . . . . . . . . . . . . . . . . . 3-53
(Models HTC 180 and 270) . . . . . . . . . . . . . . . . . . . . . . . . . 3-54
Connecting main power to the GasTrac . . . . . . . . . . . . . . . . . . . . . 3-56
Connecting main power to the vacuum pump(s) (optional) . . . . . . 3-57
Connecting main power to the dust collector(s) (optional) . . . . . . . 3-57
Installation - Conveying Lines . . . . . . . . . . . . . . . . . . . . . . . . . . 3-59
Connecting the conveying lines to the receiver(s) (optional). . . . . . 3-60
Connecting the conveying lines to the purge valve(s) (optional) . . . 3-60
Connecting the conveying lines to the vacuum pump(s) and
dust collector(s) (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . 3-61
Installation - Water Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63
Typical water lines installation drawing . . . . . . . . . . . . . . . . . . . . . 3-64
i i i
Ta b l e o f C o n t e n t s l