1. Manuals
  2. Brands
  3. Paxton Manuals
  4. Keypad
  5. Ins-30100-US
  6. User manual

Paxton Ins-30100-US User Manual

Easyprox compact keypad
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
11/12/2008
Ins-30100-US Easyprox compact keypad

Technical Support

1 800 672 PAXT
Technical help is available:
Documentation on all Paxton Access products can be found on our web site - http://www.paxton-access.com/
Layout
Parts list
Tools List
Power Drill
Drill bits 10mm, 25mm.
Philips screwdriver
Hacksaw for cutting bolts
Hammer / Mallet
Chisel 25mm
NOTE: All dimensions are shown in millimetres to maintain accuracy.
Monday - Friday from 5am - 5pm PST / 8am - 8pm EST
This unit is for Indoor use only.
support@paxton.co.uk
1) Front Lock Assembly
2) Rubber Escutcheon x2
3) Rear Lock Assembly
4) Ins-30067 - Easyprox Template
5) Left and Right Handles
6) Square Drive
7) Strike Plate Backbox
8) Strike Plate
9) Battery Pack
10) Tubular Mortice Latch
11) Latch Screws x4
12) Short Fixing Screws x4
13) Long Fixing Screws x4
Stanley knife
Adhesive tape
Pencil
Tape measure
8mm spanner
(supplied)
2mm Allen key (supplied)

Advertisement

Table of Contents
loading

Related Manuals for Paxton Ins-30100-US

Summary of Contents for Paxton Ins-30100-US

  • Page 1: Technical Support

    Technical help is available: Monday - Friday from 5am - 5pm PST / 8am - 8pm EST Documentation on all Paxton Access products can be found on our web site - http://www.paxton-access.com/ Layout This unit is for Indoor use only.
  • Page 2 Fitting the latch Step 1 Decide on the height of the latch and mark a line on the edge of the door and about 80mm across both faces. Fold the template along one of the dotted lines (right or left). Tape it to the door, the latch centre line positioned on the height mark.

  • Page 3: Fcc Compliance

    Step 10 Fit the battery pack into the unit. Replace the access plate and secure with the standoff screws. Step 11 Fit the rubber escutcheons to front plate and the back plate. Present the front and rear lock assembly to the door, locating the square drive in its recess and secure the two parts of the lock together with the fixing screws.
  • Page 4 INITIALISING A NEW SYSTEM Choose a 6 digit Programming Code and load this into the unit as follows: 6 digit Programming 6 digit Programming Code Code The factory User Code is now set to 1234 IMPORTANT NOTE: Do not set the Programming Code to 123456 The programming code must not contain the same string of digits as the user code.
  • Page 5 PROXIMITY with TOUCHLOCK mode (i) The unit must first be initialised in TOUCHLOCK mode: See TOUCHLOCK section IMPORTANT NOTE: Do not set the Programming Code to 123456 (ii) Before enrolling a card pack, set up the required operating mode, as follows: Enter 6 digit Programming Code...
  • Page 6 Normal Operation - LED Indications The external handle is free to move and is only engaged once access has been granted. The inside handle is always engaged. When access has been granted, the unit will flash the Green LED and the handle will then engage.

  • Page 7: Door Open Time

    Door open time 1. Take the door open time function card from the starter pack. 2. Present the card to the reader. The reader will start beeping. 3. Wait for the required period you wish the door to remain open. 4.

  • Page 8: Battery Replacement

    3. Remove the access plate to reveal the battery pack. - Fig 2 4. Unplug the lead and replace the pack with a new Paxton Access battery pack. - Fig 3. (NOTE: The unit will retain its settings and should not be manually reset) 5.

Table of Contents