Advertisement
Figure 2-2 Fix the Camera to the Ceiling
5.Rotate the cover of camera anticlockwise and the
direction button, auxiliary video interface, and
the DIP switch show.
2
1
3
1.Direction Button
2.Auxiliary Video Output
3.DIP Switch
Figure 2-3 Image Adjustment
l
A small monitor can be connected to the auxiliary
video output to adjust the video.
l
DIP switch is used to enable/disable WDR function.
(By disabling WDR function, video output can be
realized by both CVBS output and HD video output.)
(By enabling WDR function, video output cannot be
realized by CVBS output.)
6. Adjust the surveillance angle.
1). Loosen No.1 adjusting screw to adjust the pan
°
°
position (0 ~ 360 ).
2). Loosen No.2 adjusting screw to adjust the
°
°
tilting position(0 ~ 90 ).
3). Loosen No.3 adjusting screw to adjust the
( °
° )
rotation position 0 ~ 360 .
4).Tighten the adjusting screws.
360°
1
2
90°
360°
3
Figure 2-4 3-axis Adjustment
2.2 Wall Mounting
Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes.
Figure 2-5 Fix the Camera to the Wall
3.Route the cables to the cable hole and connect
the corresponding cables.
4.Fix the camera to the ceiling with the supplied
PA4 screws.
5.Adjust the surveillance angle as shown in the
figure 2-4.
3 Menu Operation
BACKLIGHT
DAY&NIGHT
ZOOM
CAM
INDOOR
SHUTTER
BLC
ATW
AUTO
2D NR
SHARPNESS
SPEED
TITLE
OUTDOOR
PRESET
AGC
HSBLC
AWC-SET
COLOR
3D NR
D-EFFECT
MONITOR
FOCUS
SENS-UP
WDR
MANUAL
B/W
MOTION
LSC
MODE
LENSINIT
BRIGHTNESS
OFF
TRIGGER
PRIVACY
AFLIMIT
D-WDR
DEFECT
ZOOM
HEAT
DEFOG
VIEW
CTRL
Figure 3-1 Main Menu
You can call the menu and adjust the camera
parameters with the direction button or a coaxial
camera controller (purchase separately). You can
also call the menu with supported DVR.
3.1 VIDEO.OUT
PAL or NTSC is selectable .
3.2 LANGUAGE
Chinese and English are selectable.
3.3 SETUP
3.3.1 SCENE
You can select indoor and outdoor scene modes
according to the working environments.
3.3.2 LENS
The camera is equipped with 5-50mm motorized
vari-focal lens.
Click Zoom + and Zoom - on the DVR PTZ to zoom in
and zoom out. The camera automatically focuses
after zooming in/out.
ZOOM SPEED:
Move the cursor left/right to adjust
the zoom speed.
PRESET: You can set, delete, and call the preset. 1
to 64 presets are configurable.
FOCUS MODE: Manual, Auto, and Trigger modes
are selectable. In auto mode, the camera focuses
automatically, and in manual mode, you can click
Zoom+ and Zoom- to focus.
LENSINIT:
You can reset the lens.
AFLIMIT: 20m, 10m, 6m, 3m, 1.5m, 1m, 30cm, and
10cm are selectable as the Min. focus distance limit.
ZOOM VIEW:
Enable the zoom view and the zoom
ratio displays while lens zooming in/out.
3.3.3 EXPOSURE
EXPOSURE: Manual and IRIS-PRI are selectable.
SHUTTER: AUTO,1/25, 1/75, 1/100, 1/120...1/3.5k
, 1/6k, 1/10k, 1/20k and 1/30 kare selectable.
AGC
: You can set the AGC value from 0 to 15.
SENS-UP
: You can set the SENS-UP to OFF or AUTO.
BRIGHTNESS
: You can set the brightness value
from 1 to 14.
D-WDR:
You can set the D-WDR as ON or OFF.
DEFOG
: You can set the defog function as ON to
enable the function. Position, size, and the defog
gradation are configurable.
HSBLC
EXPOSURE
1. EXPOSURE
IRIS-PRI
1. SELECT
AREA 1
2. SHUTTER
AUTO
ON 8
2. DISPLAY
3. AGC
OFF
3. LEVEL
---|------ 20
4. SENS-UP
---
4. MODE
ALL DAY
5. BRIGHTNESS
---|------ 40
5. BLACK MASK
ON
6. D-WDR
OFF
8
6. DEFAULT
7. DEFOG
OFF
7. RETURN
RETURN
8. RETURN
RETURN
Figure 3-3 HSBLC
Figure 3-2 Exposure
3.3.4 Backlight
:
WDR Set the WDR status as ON or OFF.
Backlight Compensation (BLC):
-GAIN:
Set the gain of BLC as High, Middle, or Low.
-AREA:
Press the up/down/left/right button to
define the BLC position and size. Select RET or
AGAIN to go back the BLC menu or re-define the
BLC area.
-Default:
Restore the BLC settings to the default.
HSBLC: Select an HSBLC area. Set the DISPLAY
status as ON. Press the up/down/left/right button
to define the area position and size. Set the HSBLC
LEVEL from 0 to 100. Select ALL DAY or Night for the
HSBLC mode. Set the BLACK MASK status as ON or
OFF.
3.3.5 White Balance (WB)
MANUAL, ATW (Auto-tracking White Balance),
AWC→SET are selectable.
3.3.6 Day & Night
Auto, Trigger, Color, and B/W are selectable for
DAY and NIGHT switches. You can enable IRF in
trigger mode.
3.3.7 NR
2D NR
: You can set 2D NR status as ON or OFF.
3D NR
: Set the Smart NR status as ON and adjust
the 3D smart NR sensitivity ranges from 0 to 100.
Set the 3D NR LEVEL ranges from 0 to 100. Set the
START. AGC level as the threshold to enable AGC,
and set the END. AGC level as the threshold to
disable AGC.
3D NR
2D&3D NR
1. SMART NR
OFF
2. LEVEL
------|--8 0
1. 2DNR
OFF
3. START. AGC -|--------10
8
2. 3DNR
ON
4. END. AGC
-|--------10
3. RETURN RETURN
5. RETURN
RETURN
Figure 3-4 NR
Figure 3-5 3D NR
3.3.8 SPECIAL
Camera Title:
Edit the camera title on this section.
D-effect:
-FREEZE:
Set the freeze function as ON or OFF.
-MIRROR:
OFF, MIRROR, V-FLIP, and ROTATE are
selectable for mirror.
-D-ZOOM:
Define the zoom ratio of certain area
from 2 to 62.
-NEG.IMAGE:
Set the NEG IMAGE as ON or OFF.
MOTION
SPECIAL
1. CAM TITLE
OFF
1. SELECT
AREA 1
8
2. D-DFFECT
2. DISPLAY
ON8
3. MOTION
OFF
3. SENSITIVITY
----|---- 30
4. PRIVACY
OFF
8
4. MOTION VIEW ON
5. DEFECT
8
8
5. DEFAULT
6. HEATCTRL
6. RETURN
RETURN
7. RETURN
RETURN
Figure 3-7 Motion Detection
Figure 3-6 Special
Motion: Select a MOTION area. Set the DISPLAY
status as ON or OFF. Press the up/down/left/right
button to define the position and size of the area.
Set the SENSITIVITY from 0 to 100. Set the
MOTION VIEW status as ON or OFF.
Privacy: Select a PRIVACY area. Set the DISPLAY
status as INV, MOSAIC, COLOR or OFF. Press the
up/down/left/right button to define the position
and size of the area. Up to 8 areas are configurable.
Defect: LIVE DPC and STATIC DPC are selectable
in this section.
PRIVACY
ADJUST
1. SELECT
AREA 1
8
--------|15
1. SHARPNESS
2. DISPLAY
MOSAIC
8
3. COLOR
10
2. MONITOR
LCD
4. TRANS.
1
3. LSC
OFF
8
4. RETURN
RETURN
5. DEFAULT
6. RETURN
RETURN
Figure 3-8 Privacy Mask
Figure 3-9 Adjust
HEAT CTRL: AUTO, ON and OFF are selectable in
this section.
3.3.9 ADJUST
Sharpness
: Adjust the sharpness from 0 to 15.
Monitor
: Monitor CRT, and Monitor LCD are
selectable.
LSC
: Set the LSC status as ON or OFF.
3.3.10 RESET
Reset all the settings to the default.
3.3.11 EXIT
Press OK to exit the menu.
Advertisement
