Do you have a question about the GATOR LS50L2 and is the answer not in the manual?
Questions and answers
James Cassidy
April 29, 2025
Hi our punch is not working we think that the hydraulic oil needs replacing and topping up how can we do this
1 comments:
Mr. Anderson
May 15, 2025
To replace and top up hydraulic oil in a Greenlee LS50L2 punch:
To check and top up the oil: 1. Remove the screws holding the housing cover together. 2. Point the tool head downward and remove the oil reservoir plug. 3. Fill the reservoir with hydraulic oil if necessary. 4. Replace the oil plug and housing cover.
To replace the hydraulic oil (annually or after 10,000 punches): 1. Replace the hydraulic oil completely. 2. Send the tool to a Greenlee Authorized Service Center for inspection.
Do not use solvents or flammable liquids to clean the tool body.
Keep this manual available to all personnel. All specifications are nominal and may change as design improvements occur. Greenlee Textron Inc. shall not be liable for Do not discard this product or throw away! damages resulting from misapplication or misuse of its products.
Failure to observe this warning could result in severe injury or death. Greenlee / A Textron Company GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
Page 4
All of the punch threads must be engaged by the draw stud threads. Incomplete assembly could cause a component failure. • Use only Greenlee punches, dies, and draw studs. Other manufacturers’ components might not with- stand the forces generated by this punch driver.
• Do not place a battery on moist ground or grass. Moisture may create a short circuit and damage the battery. Failure to observe these precautions may result in injury or property damage. Greenlee / A Textron Company GlobalTestSupply www. .com Find Quality Products Online at:...
40 cycles, allow the tool to cool for 15 minutes. Greenlee replacement parts. A damaged or • Do not secure this tool in a vise. This tool is improperly assembled tool can break and strike designed for hand-held operation.
Page 8
9. Pull the trigger. The LS50L2 will automatically shut off when it senses that the punch is completely through the material. Greenlee / A Textron Company GlobalTestSupply www. .com Find Quality Products Online at:...
Page 9
7/8" (22.2 mm) Punching mild steel with Pilot Hole 1-1/2" (ø 1.951" [49.6 mm]) to 3" (ø 3.539" [89.9 mm]) 2113B conduit sizes Draw Stud Punch Greenlee / A Textron Company GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
Page 10
7/8" (22.2 mm) Punching Pilot Hole stainless steel with 3/4" (ø 1.115" [28.3 mm]) to 2" (ø 2.416" [61.5 mm]) 29452 Draw Stud conduit sizes Punch Greenlee / A Textron Company GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
Page 11
1.250" x 1.380" [31.8 mm x 35.1 mm] rectangular 60117 3/8" Draw Stud End with Long Threads Threads with Flats 60258 1/2" Counter Nut Pilot Hole Punch Greenlee / A Textron Company GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
34421 3/8" Draw Stud Punching with Electronic Connector Panel Punches End with Long Threads Threads with Flats 04638 3/8" Counter Nut Punch 7/16" (11.1mm) Pilot Hole Greenlee / A Textron Company GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
The head should rotate freely. If flying debris or hydraulic oil. damage is detected, send the tool to a Greenlee Authorized Service Center for inspection. After use: 1. Use a damp cloth and mild detergent to clean the housing.
Charge or replace battery. seconds. Tool loses oil. Damaged internal seal. Return tool to a Greenlee Authorized Service Center. Note: For Warranty Service or Repair, contact Greenlee customer service at 800-435-0786. Greenlee / A Textron Company GlobalTestSupply www. .com Find Quality Products Online at:...
Need help?
Do you have a question about the GATOR LS50L2 and is the answer not in the manual?
Questions and answers
Hi our punch is not working we think that the hydraulic oil needs replacing and topping up how can we do this
To replace and top up hydraulic oil in a Greenlee LS50L2 punch:
To check and top up the oil:
1. Remove the screws holding the housing cover together.
2. Point the tool head downward and remove the oil reservoir plug.
3. Fill the reservoir with hydraulic oil if necessary.
4. Replace the oil plug and housing cover.
To replace the hydraulic oil (annually or after 10,000 punches):
1. Replace the hydraulic oil completely.
2. Send the tool to a Greenlee Authorized Service Center for inspection.
Do not use solvents or flammable liquids to clean the tool body.
This answer is automatically generated