1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Security System
  5. ADEMCO 4110XM
  6. Installation manual

Honeywell ADEMCO 4110XM Installation Manual

Hide thumbs Also See for ADEMCO 4110XM:
Table of Contents

Advertisement

Quick Links

See also: User Manual
N5478V5 7/96 Rev. C
ADEMCO 4110XM
ADEMCO
ADEMCO
ADEMCO
SECURITY SYSTEM
SECURITY SYSTEM
SECURITY SYSTEM
SECURITY SYSTEM
Installation Guide
Installation Guide
Installation Guide
Installation Guide
4110XM
4110XM
4110XM

Advertisement

Table of Contents
loading

Related Manuals for Honeywell ADEMCO 4110XM

Summary of Contents for Honeywell ADEMCO 4110XM

  • Page 1 ADEMCO ADEMCO ADEMCO ADEMCO 4110XM 4110XM 4110XM 4110XM SECURITY SYSTEM SECURITY SYSTEM SECURITY SYSTEM SECURITY SYSTEM Installation Guide Installation Guide Installation Guide Installation Guide N5478V5 7/96 Rev. C...

  • Page 2: Recommendations For Proper Protection

    RECOMMENDATIONS FOR PROPER PROTECTION The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for the Protected Premises. Recommendations for Smoke and Heat Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below.

  • Page 3: Table Of Contents

    Table of Contents Section 1. System Features ................................1 Zones Supported .................................. 1 Security Codes ..................................1 Keypad Panic Keys ................................1 Alarm Output ..................................1 Communications Outputs ..............................1 Compatible Devices ................................1 Section 2. Mounting and Wiring the Control .......................... 3 Installing the Cabinet and PC Board ..........................
  • Page 4 - ii -...

  • Page 5: Section 1. System Features

    SECTION 1 System Features The 4110XM is a microprocessor-based security control intended for hard-wired applications. Zones Supported Up to six (6) hardwire zones, having the following characteristics: EOLR supervision supporting N.O. or N.C. sensors. • 300-500 msec normal response. • Zone 3 programmable for Fast Response to open (10mS).
  • Page 6 Installation and Setup Guide Smoke Detectors (4-wire only) Model Type 1412 Ionization Products of Combustion Detector 2412 Photoelectric Smoke Detector 2412TH Photoelectric Smoke Detector)w/135º F (57º C) Heat Detector) Fire Supervisory Module Model Type EOLR-1 EOL Relay Module (supervises power for 4-wire fire zone). - 2 -...

  • Page 7: Section 2. Mounting And Wiring The Control

    SECTION 2 Mounting and Wiring the Control 1. Installing the Cabinet and PC Board Refer to the Summary of Connections diagram on the inside back cover of this manual for terminal connections when following these procedures. RETAINER CLIP a. Mount the control cabinet to a sturdy (NOTE POSITION) wall in a clean, dry area, which is not readily accessible to the general public,...

  • Page 8: Connect Telephone Line

    Installation and Setup Guide 6. Connect the Telephone Line Make sure telephones on the premises are connected only through the alarm control panel (disconnect from the incoming phone line at the telephone jack). This is necessary to have true line seizure. 7.

  • Page 9: Section 3. Programming Overview

    SECTION 3 Programming Overview About Programming The Telco hand-off feature allows a technician or user at the site to call the downloading facility from the control panel phone line and initiate a site download. By entering the Master Code + [#] + [1] while on the line, the control will immediately be on-line with the modem at the downloading facility, where the operator can begin downloading.

  • Page 10: Zone Type Definitions

    Installation and Setup Guide Zone Type Definitions Zone types define the way in which the system responds to the faults in each zone. Zone Type Description 0 – Zone Disabled 1 – Entry/Exit Burglary • Provides exit delay time when panel is armed in any arming mode.

  • Page 11: Section 4. Data Field Programming

    SECTION 4 Data Field Programming About Data Field Programming The following pages list this control’s data fields in numerical order. Valid entries for each field are shown in italics. Explanations and special notes are presented below the entries. Use the separate Programming Guide to record the data for this installation. Data field programming involves making the appropriate entries for each of the data fields.
  • Page 12 Installation and Setup Guide 6 6 6 6 † Entering a number other than the one specified will give Primary Phone No. unpredictable results. Enter up to 12 digits †† Can only be used if primary reporting format is ADEMCO Contact ID®. Do not fill unused spaces.
  • Page 13 Data Field Programming 6 6 6 6 6 6 6 6 Zone 8 Alarm Report Code (Duress) Trouble Restore Report Code 0 = No Report, 1-9, B-F (as described above). 0 = No Report, 1-9, B-F (as described above). Console Panic: Key B or *+# Sent when a trouble in a zone is restored.
  • Page 14 Installation and Setup Guide - 10 -...

  • Page 15: Section 5. System Operation

    SECTION 5 System Operation USER ACCESS CODES Refer to the User Guide for detailed procedures on adding/deleting security codes and changing user attributes Changing the Master Code Master Code + [Code Key] + [1] + New Master Code + New Master Code Again Adding a Secondary User Code Master Code + [Code Key] + User # (2-7) + Desired 4-Digit Access Code.
  • Page 16 Installation and Setup Guide Keyswitch Keyswitch LED Indications Keyswitch Operation Meaning • To arm AWAY, turn key and release within a 1/2 second. Disarmed & Not Ready • To arm STAY, turn and hold key for longer than 2 seconds. Slow Flash Armed Ready •...

  • Page 17: Section 6. Testing & Troubleshooting The System

    SECTION 6 TESTING &TROUBLESHOOTING After installation is completed, the Security System should be carefully tested as follows: Test Mode 1. With the system disarmed, check that all zones are intact. If a NOT READY message displays, press the [6] key to display the faulted zone(s). Restore faulted zone(s) if necessary. 2.

  • Page 18: Troubleshooting Guide

    Installation and Setup Guide Troubleshooting Guide SYMPTOM POSSIBLE CAUSE REMEDY Low Battery message on System battery is low or missing. Check system battery. keypad. Periodic beep(s) from keypad. System is in TEST mode. Enter "Code" + OFF to exit TEST mode. False alarms.

  • Page 19: Section 7. Specifications

    Section 6: SECTION 8 Specifications 4110XM SECURITY CONTROL 1. Physical: ........12-1/2" W x 14-1/2" H x 3" D (318mm x 368mm x 76mm) 2. Electrical: Voltage Input: ......16.5VAC from plug-in 25VA transformer, Ademco No. 1321/TF2 (in U.S.A.), 1321CN (in Canada) Rechargeable Back-Up Battery: 12VDC, 4AH (Gel type).

  • Page 20: Regulatory Agency Statements

    Installation and Setup Guide REGULATORY AGENCY STATEMENTS FEDERAL COMMUNICATIONS COMMISSION STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.

  • Page 21: The Limitations Of This Alarm System

    WARNING THE LIMITATIONS OF THIS ALARM SYSTEM While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons.

  • Page 22: Summary Of Connections Diagram

    - 18 -...

  • Page 23: Limited Warranty

    WARRANTY INFORMATION For the latest US warranty information, please go to: www.honeywell.com/security/hsc/resources/wa - 19 -...
  • Page 24 2 Corporatee Center Drive, Suite 100 N5478V5 P.O. Box 9040, Melville, NY 11747 Copyright © 1996 Honeywell International Inc. N5478V5 7/96 Rev. C...

Table of Contents