Page 1
User & Installation Manual Micro Joystick Very small, proportional wheelchair joystick Micro Joystick Omni (P002-51) - R-net (P002-52) Or version for different wheelchair electronics connection...
Important information about this Manual Congratulations for choosing a mo-Vis product! If you would like to learn more about mo-Vis and its products, we invite you to visit our website: www.mo-vis.com. Before you install or begin using this product, it is important that you read and understand the content of these installation and operating instructions, the safety instructions in particular.
Page 6
We reserve the right to make changes to the product without prior notice. Ordering documentation You can download additional copies of this User & Installation manual on the mo-Vis website: www.mo-vis.com.
Support, scrapping and spare parts Technical support In case of technical problems, we advise you to contact your dealer. If the dealer is not available, or unknown, please contact mo-Vis bvba by email support@mo-vis.com or by phone +32 9 335 28 60.
Warranty mo-Vis bvba warrants the Micro Joystick to be free from defects in material and workmanship for a period of 2 years under proper use, care and service. All warranties only cover parts and do not extend beyond the initial purchaser from an authorised mo-Vis dealer.
Page 9
The warranty will be void if the product has been installed or used improperly, or if it has been repaired or any part replaced by persons other than mo-Vis or an authorised dealer. The Micro Joystick, integrated cabling and interface included, is considered as a non-serviceable part.
General The Micro Joystick is intended to be fitted on any power wheelchair with Omni (P002-51) or R-net (P002-52) connection. Other versions for different wheelchair connections are available. Check the connection manual or contact your dealer or mo-Vis for more information.
Page 11
CAUTION! Limited liability mo-Vis accepts no liability for personal injury or damage to property that may arise from the failure of the user or other persons to follow the recommendations, warnings and instructions in this manual.
Page 12
Use only spare parts or accessories approved or recommended by mo-Vis. All other use could lead to changes which might impair the function and safety of the product. It could also lead to the warranty becoming void.
Design and function of the Micro Joystick Purpose The Micro Joystick is a very small, proportional joystick specifically designed for people with very poor or weak muscle strength and/or limited movements. The joystick can easily be controlled by e.g. finger, chin, tongue, lip…...
Page 14
Fully adjustable to individual possibilities and needs with well- thought electronics Easily configurable with the free mo-Vis Configuration software: positioning of the joystick. For other parameters, the wheelchair software settings are used. Compatible with multiple types of wheelchair electronics .
You can equally use any other mounting system. Parts and accessories Micro Joystick package A Micro Joystick package consists of the following parts: Product description Product code Micro Joystick set, P002-51 (Omni) with integrated P002-52 (R-net) cabling and interface Or version for (illustration: Omni different...
Page 16
M004-70 D6 50 mm Micro Joystick ball M006-08 Micro Joystick cup M006-09 Micro Joystick manual D-P002-51-70-00 Connection manual D-P002-81-70 (Onmi) D-P002-85-70 (R-net) Or version for different connection Micro Joystick unit detail The connections of the Micro Joystick Interface unit have protective...
Always put or keep the protective cover in case connections are not used. Ordering spare parts Spare parts and accessories must be ordered by the dealer at mo-Vis bvba. Always mention Product code & Product description of items to be ordered.
Profiles Depending on your profile (user, attendant, dealer, OEM), you will be able to configure a number of parameters for the Micro Joystick. For a user profile, no password is required. Attendant, Dealer and OEM profiles require a password. Intended use The Micro Joystick is a joystick module which can be connected directly to the wheelchair electronics to control the wheelchair functions.
Page 19
WARNING! Mind damaging the unit and wiring. Make sure that cabling is mounted in such a way that excessive wear and tear is avoided. WARNING! Do not use the joystick as only support for your hand or limbs. Movements and shocks may disrupt controls. Functioning The movements of the joystick are translated into according movements of the wheelchair, e.g.
Page 20
Safe driving It is mandatory to have a wheelchair power on/off switch – which immediately shuts down the wheelchair power and electronics – within easy reach of the user while driving. This allows to instantly stop the wheelchair in case of problems or an emergency. WARNING! The on/off switch must be available to the user at all times.
Installation instructions Preparations Qualified service engineer Only a qualified service engineer may install the Micro Joystick. WARNING! An incorrect programming of the wheelchair electronics may cause damage to the devices, or injury to the user. Tools Use an Allen wrench to install the Quick-to-mount and Micro Joystick. CAUTION! Use the proper tools to install and adjust the Micro Joystick.
Page 22
Where which part of the Micro Joystick should be placed. How the Micro Joystick will be operated: hand, chin, lip or tongue. A robust and reliable positioning. Hard or sudden movements of the wheelchair may not disorganise the installation. CAUTION! Protect the joystick against bumps WARNING!
If needed, you can change this positioning in steps of 90° with the mo-Vis Configurator software. Place the mounting ring around the joystick housing. Secure the Quick-to-mount half clamp to the mounting ring.
Page 24
Contact your dealer or mo-Vis for more information, or ordering additional clamps or rods. Place and secure the Interface Unit and all cabling on the wheelchair. WARNING! Mind damaging the unit and wiring. Make sure that cabling is mounted in such a way that excessive wear and tear is avoided.
Defining position (parameters) If the Micro Joystick is not mounted with the arrow at the bottom pointing forward, you can adjust the Joystick direction in steps of 90° with the mo-Vis Configurator software. This software must be installed and ready to use on a pc.
Parameter settings Please see “Parameter settings” for a list of all parameter settings. Testing After installation of the Micro Joystick, execute the following tests before the wheelchair is delivered or put into service, in according order: Check the Micro Joystick for intactness Operational test Test drive Stop test...
Page 27
Operational test WARNING! Execute this test only on a level surface, with at least one meter of free space around the wheelchair. Activate the wheelchair operating system. Check for any error message. Move the joystick slowly forward until you hear the parking breaks switch off.
Page 28
Check no cabling or parts may get damaged or hindered in any possible position of the wheelchair. Stop test Drive full speed ahead and shut down the wheelchair with the power on/off switch. The wheelchair may not suddenly stop, but must slow down to a gradual stop.
First time use Dealer assistance During first time use by the user it is advised that the dealer or service engineer assists and explains the different possibilities to the customer (the user and/or his attendant). If needed, the dealer can make final adjustments. User testing It is important that the customer is fully aware of the installation, how to use it and what can be adjusted to optimise his experience.
Using the Micro Joystick Conditions of use The Micro Joystick is intended for use as installed by the dealer, in accordance to the installation instructions in this manual. The foreseen conditions of use are communicated by the dealer or service engineer to the user and/or attendant during the first time use. If the usage conditions change significantly, please contact your dealer or a qualified service engineer to avoid excessive wear and tear or unintended damage.
Let the ball or cup dry before putting it back If the ball or cup is damaged, worn out or remains dirty, replace. Contact your dealer or mo-Vis for ordering spare parts (Micro Joystick ball = product code M006-08; Micro Joystick cup = product code M006-09).
Page 32
We advise to have at least yearly a full check of the wheelchair and its operating systems by a qualified service engineer. Contact your local dealer or mo-Vis for more information. Maintenance free The Micro Joystick is maintenance-free. Under regular circumstances of use, the joystick, interface unit and different parts do not require additional maintenance.
Parameter settings With the mo-Vis Configurator software you can change the parameters of the Micro Joystick. Depending on your profile (user, attendant, dealer, OEM), you will be able to change a number of parameters. Mounting Settings (User Level) Setting Description...
Setting Description Parameters Prevents creeping of the wheelchair after releasing the joystick. Note: Most wheelchair electronics have their own deadband setting. It is advised to keep the default setting. Compensation Setting Description Parameters Compensa Lowers forward/backward (Y) Very almost no tion factor driving speed on rough terrain.
Page 35
Setting Description Parameters Front wheel-driven wheelchairs are less affected by this factor than back wheel-driven ones. To limit the steering reaction if the No compen- None compen- wheelchair overreacts on steering sation sation commands. This may happen due X = 50% of Y 1/2 Y to compensation on the X direction level...
- which means that the joystick is active again - if the angle becomes less than 60 degrees. The use of this functionality certainly makes sense when a mo-Vis joystick is integrated in a tray or other tilting surface / mounting aid. The default setting of the Tilt sensor is ‘off’.
Technical data Product description & code Micro Joystick Omni (P002-51), R-net (P002-52) Or version for different wheelchair electronics connection Interface connectors 3.5 mm mono jack on/off (pwr) 3.5 mm mono jack mode (in) Mini USB ...
Page 40
Installation date: . . / . . / ..Dealer: ....Dealer stamp: Serial number sticker...
Need help?
Do you have a question about the P002-51 and is the answer not in the manual?
Questions and answers