1. Manuals
  2. Brands
  3. Windsor Manuals
  4. Floor Machine
  5. EPB2
  6. Owner's manual

Windsor EPB2 Owner's Manual

Carpet extractor
Hide thumbs
Table of Contents

Advertisement

Quick Links

MODELS: EPB2, EPB2-J
REV.
A
98255 9/15/97
INDUSTRIES, INC.,
CONTENTS:
2
3
4
5
6
7
8
10
12
13
14
1351 W. Stanford Ave., Englewood CO 80110 USA *303–762–1800*FAX 303–762–0817
TM
Owners Guide
Safety Instructions
Grounding Instructions
Operating the Extractor
Operations and Maintenance
Service
Chassis assembly
Brush Housing and Drive Assembly
Tank Assembly
Wiring Diagrams
Notes
Warranty

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EPB2 and is the answer not in the manual?

Questions and answers

Related Manuals for Windsor EPB2

Summary of Contents for Windsor EPB2

  • Page 1 Owners Guide CONTENTS: Safety Instructions Grounding Instructions Operating the Extractor MODELS: EPB2, EPB2-J Operations and Maintenance Service Chassis assembly Brush Housing and Drive Assembly Tank Assembly REV. Wiring Diagrams Notes Warranty 98255 9/15/97 INDUSTRIES, INC., 1351 W. Stanford Ave., Englewood CO 80110 USA *303–762–1800*FAX 303–762–0817...

  • Page 2: Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. WARNING: To reduce the risk of fire, electric shock, or injury: Do not operate without filters (dry or wet) in place.

  • Page 3: Grounding Instructions

    WARNING: INSPECTION Improper connection of the equipment–grounding conductor Carefully unpack and inspect your extractor for shipping dam- can result in a risk of electric shock. Check with a qualified age. Each unit is operated and thoroughly inspected before ship- ping, and any damage is the responsibility of the carrier, who electrician or service person if you are in doubt as to whether should be notified immediately.
  • Page 4 ACCESSORY TOOLS retainer to handle. The POWER ESCORT is easily adapted for use with the Plug power cable from machine following WINDSOR accessory tools; DHT–UPH3–SW– into properly grounded wall outlet. SFW–SW/PRO Using a clean container, fill solution tank with hot water.
  • Page 5 PERIODIC MAINTENANCE To inspect motor brushes, remove brush holder assembly. Twice a month, flush a white vinegar solution (One quart vinegar Brushes should be replaced when worn to 3/8 inch or after to two gallons of water) or anti–browning solution (mixed as about 250 operating hours.

  • Page 6: Chassis Assembly

    BELT ADJUSTMENT SOLENOID VALVE If the machine continues to drip solution from the manifold after pump is switched off check for: (A) Alkaline buildup in solution lines (B) Lint When servicing brush motor or brush assembly always check or debris lodged in the solenoid valve. belt for proper tension.
  • Page 7 CHASSIS ASSEMBLY Qty. Part No. Description Serial No. Notes: From 54077 Muffler, Vac Exhaust 20046 Clamp, 2.25” Worm Gear 39247 Hose, Vac Exhaust x 19” 39032 Hose, Hose, 3/8 Rubber x 15” 87015 Washer, 9/16 ID x 1.06 OD 56014 Nipple, 1/4 Close 40038 Hosebarb, 1/4 MPT x 3/8 45D...
  • Page 8 Washer, #8 Int Star 70052 Screw, 8–32 x 3/8 PHMS 62225 Plate, Assembly Motor 87018 Washer, #10 x 9/16 OD 57030 Nut, 10–32 Nylock 64035 Pulley, Motor, 3/8 Bore 70084 Set Screw, 8–32 x 3/16 KCP 11023 Belt, EPB2 98255 9/16/97...
  • Page 9 Washer, #10 star 70020 Screw, 1/4–20 x 1/2 HHMS 14280 Bracket, Brush Housing Lift 73220 Spacer, EPB2 Cable 27332 Cable, EPB2 Brush Lift 87013 Washer, 1/4 ID x 5/8 OD 87025 Washer, 1/4 Star 70190 Screw, 1/4–20 x 1/2 BHCS 57047 Nut, 1/4–20 Lock...

  • Page 10: Tank Assembly

    TANK ASSEMBLY 58AB 19AB Qty. Part No. Description Serial No. Notes: From 73250 Strainer, 80 Mesh x 3/8 FPT 14076 Bushing, 3/8 MPT x 1/4 FPT hex 87015 Washer, 9/16 x 1.06 OD 56014 Nipple, 1/4 Close 75082 Tank, EPB–2 Solution 36055 Grommet, 1/2 ID x 1/4 Grrove 50379...
  • Page 11 Cord End, 115A 15A Fem–T–Lock 23086 Cord Asm, 115V 14/3 x 50’ 26006 Cord End, 125V 15A 3–WIRE 50272 Label, EPB wiring (115V) 50645 Label, EPB2 100V W/O Sol 20035 Clamp, 7/16 Plastic cable 27079 Cuff, 1.5” White Hose 39230 Hose Assembly 20041 Clamp, 2.0”...

  • Page 12: Wiring Diagrams

    100 VOLT WIRING DIAGRAM 115 VOLT WIRING DIAGRAM 98255 9/16/97...

This manual is also suitable for:

Epb2-j

Table of Contents