Subscribe to Our Youtube Channel
Related Manuals for Windsor EXP
Summary of Contents for Windsor EXP
-
Page 1: Cover Sheet
CARPET EXTRACTOR MODEL POWER SOURCE 115V ELECTRIC EXPJ 100V ELECTRIC Read these instructions before using the machine 98363 10/19/02... -
Page 2: Table Of Contents
DATE OF PURCHASE- SERIAL NUMBER- SALES REPERESENTIVE- DISTRIBUTOR NAME- OPERATIONS GUIDE NUMBER – 98363 ©Copyright 1996 Windsor Industries, Printed in U.S.A. TABLE OF CONTENTS Vac, Solution Tank, Control Panel Parts List ..15 Cover Sheet............1 Brush, Brush Motor, Frame Assembly ....16 Data Log / Table of Contents....... -
Page 3: Information In This Guide
This Owner’s Guide contains valuable information PART SECTIONS about the operation, maintenance, service and part numbers for repairs of your Windsor machine. To easily locate the part needed, please refer to The Please read this introductory page thoroughly to Table of Contents for component locations to find become familiar with the contents of the owner’s... -
Page 4: Safety
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes. Maintenance and repairs must be done by qualified personnel. If foam or liquid comes out of machine, switch off immediately. SAVE THESE INSTRUCTIONS EXP 98363 03/24/00... -
Page 5: Hazard Intensity Level
Unless Operation Guide is Read and understood. In Flammable or Explosive areas. In areas with possible falling objects. WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts. EXP 98363 03/24/00... -
Page 6: Operations
Aromatic Hydrocarbons electrician. D-Limonene This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in “Fig. A”. A temporary adaptor that looks like the adaptor in EXP 98363 7/1/96... -
Page 7: Option Controls
1. Make a loop in power cord approximately 12” from strain relief on m achine. 2. Slide cord loop through slot Vacuum in retainer arm. Pull slack Shoe / Brush cord back through slot to H ousing secure. Attach retainer to handle. EXP 98363 03/24/00... -
Page 8: Operating Instructions
This extractor is easily adapted for use the following OPERATING THE MACHINE Windsor accessory tools: D HT-U PH3-SW -SFW-SW /PR O- DD H-SPW Vacuum the carpet and make sure it is cleared of Lift flap on the front of vac shoe and insert hose cuff surface debris before cleaning. -
Page 9: Maintenance
NOT E: Do not use pins, wire, etc. to clean spray jet nozzle as When reinstalling brush, check belt for proper this w ill deform the jet and destroy the spray pattern. tension. PERIODIC MAINTENANCE cont.. EXP 98363 03/24/00... -
Page 10: Maintenance Cont
Wash jet and blow dry. Do not use pins or wire location to remove obstruction as this will change spray ground of brushes pattern. VAC MOTOR BRUSHES cont.. NOTE: When replacing electrical component parts refer to Wiring Diagram for proper connection. EXP 98363 03/24/00... -
Page 11: Troubleshooting
C heck for and correct any loose wires Faulty pump R epair or replace Solution valve adjustm ent Adjust solution valve cable until valve operates when handle is pulled. Incorrect jet orientation Align slit in jet parallel with center line of brush. EXP 98363 03/24/00... -
Page 12: Wiring Diagram
WIRING DIAGRAM 115V E XPE RT O RG BL K EXP 98363 03/24/00... -
Page 13: Service Schedule
Check cables for fraying Check the spray bar (manifold) for damage; replace if broken or bent Check condition of vac shoe and frame for damage Check overall performance of machine Check vac motor carbon brushes EXP 98363 10/19/02... -
Page 14: Vac, Solution Tank, Control Panel Assembly
VAC/SOLUTION TANK/CONTROL PANEL 44(5) 45(5) 12(2) 45(2) 25(3) 48(2) 44(6) 13(2) 32(2) 31(2) 40(2) 44 REF 45(6) 39(4) 47(2) 26(4) 35(4) 3(4) 21(2) 22(2) EXP 98363 10/22/01... -
Page 15: Vac/Solution Tank/Control Panel Parts List
HOSE, 1.5” X 14” VAC 57208 NUT PG11 METAL, 1.024 OD X 0.73 ID 70211 SCR, 10-32 X 3/4 PH. BLK NYLON 53771 VAC MOTOR ASM, 115V EXP. 53780 VAC MOTOR ASM, 100V EXP. 500551 LABEL, CONTROL PANEL MAIN 27632... -
Page 16: Brush, Brush Motor, Frame Assembly
Brush brkt Diagram C Diagram B machine Housing 10(3) 13(2) Diagram A Diagram B 8(2) 13(2) 7(2) Wiring Asm. 35(2) REF. (88004) Inside rear wall of housing 8(4) 37 Housing 41(4) 9(4) 10(5) *-left side only Diagram C EXP 98363 10/17/01... -
Page 17: Parts List
70604 SCR, 10-32 X 5/8 PHMS BLK 87189 WASHER, .2 ID X .5 OD BLK SS NOTE: The left and right sides of the machine are assigned as if standing behind the machine in the operator’s position. EXP 98363 10/17/01... -
Page 18: Pump Assembly
PUMP ASSEMBLY 11(2 ) Valve 1(2) Solution Tank 5(2 ) 6(2 ) NOTE : Head of screw on this hose clamp sh all point towards center of pump h ead as shown. Accessory Port EXP 98363 03/27/00... -
Page 19: Pump Assembly Parts List
HOSEBARB, 1/4 MPT X 1/4 40065 HOSEBARB, 1/4 MPT X 1/4 X 90° 65164 PUMP ASM, EXPERT 70581 SCR, 10-32 X 3/8 HHTFW/WASH 78024 TEE, 1/4 BRANCH 40033 HOSEBARB, 1/4 MPT X 3/8 90° 20042 CLAMP, 3/8 (D-SLOT) EXP 98363 03/27/00... -
Page 20: Solution Lever, Main Handle Assembly
SOLUTION LEVER/MAIN HANDLE Solution Lever 1(3) 34331 41 REF 42(2) 4(3) VIEW A-A 12(2) 13(2) 29(2) 34(4) 23(2) 39(2) Rear View See Rear View EXP 98363 03/27/00... -
Page 21: Solution Lever, Main Handle Assembly Parts List
WASHER, .52 1.25 FLAT PLTD 87016 WASHER, #10 LOCK 87139 WASHER, 3/16 FLAT USS 441847 (QTY WAS 3) 67397 ROD, HANDLE ADJUSTMENT EXP II 80604 RING, RUE COTTER 1/4” 51142 LEVER, HANDLE LOCK 66133 PIN, CLEVIS 51184 LOCK, HANDLE ADJUSTMENT... -
Page 22: Recovery Tank Assembly
RECOVERY TANK TO REAR COVE R 4(3) EXP 98363 03/27/00... -
Page 23: Recovery Tank Assembly Parts List
GASKET, DOME 62465 PLATE, COVER 70114 SCR, 10-32 X 3/4 POLYFAST 35167 GASKET, COVER 75212 TANK, RECOVERY 34140 FILTER, VAC INTAKE 78162 TUBE, 1.5 PVC X 4.88” 27417 CORD, 1/8 X 1/2” 500009 LABEL, WARNING 500016 LABEL, EXPERT EXP 98363 10/22/01... -
Page 24: Solution Plumbing Spray Jet Assembly
SOLUTION PLUMBING/SPRAY JET 39507 PUMP EXP 98363 03/27/00... -
Page 25: Solution Plumbing Spray Jet Assembly Parts List
ELBOW, 1/8 45° STREET 39509 HOSE, 3/8” CLEAR X 15.5” 62800 PLATE, GUARD EXPERT 40064 HOSE BARB, 1/8” FPT X 1/4” OPEN 44066 JET, BRASS MINI-QUICK 44052 JET BODY, MINI-QUICK W/SEAL OPEN 87185 WASHER, 3/8 SEALING X 3/4 OD EXP 98363 03/27/00... -
Page 26: Spare Parts And Accessories
GASKET, BOTTOM COVER 73169 STRAIN RELIEF, CORD HOOK 34140 FILTER, VAC INTAKE ACCESSORIES SW – STANDARD WAND SPW – STANDARD WAND PROFESSIONAL DHT – DELUXE HAND TOOL DHTK – DELUXE HAND TOOL KIT DDH – DOUBLE DRY HAND EXP 98363 03/27/00... -
Page 27: Warranty
The Machine Registration Card must be completed and returned immediately at the time of purchase. If proof of purchase cannot be identified, the warranty start date is 90 days after the date of sale to an authorized Windsor distributor. Parts replaced or repaired under warranty are guaranteed for the remainder of the original warranty period. - Page 28 If difficulty develops during the warranty period, contact the authorized Windsor agent from whom the product was purchased. Windsor Industries, Inc. may elect to require the return of components to validate a claim. Any defective part to be returned must be shipped freight prepaid to an authorized Windsor Distributor/Service Center or to the Windsor factory.
Need help?
Do you have a question about the EXP and is the answer not in the manual?
Questions and answers