VIA Technologies ART-3000 Quick Manual

ART-3000
Quick Guide

Key Features:

Fanless, Compact and Rugged System
•
Support Triple Display with Dual Independent Display
•
Dual Gigabit Ethernet Support
•
Wide Range of Power Source
•
Flexible Mounting Options
•
P/N: 99G51-012994-10

Opening the Chassis

1
Step 1
Remove the screws on front and rear side of the chassis.
The ART-3000 is a fanless embedded system intended for various indus-
trial and embedded applications. Its based on the Em-ITX form factor and
powered by a high performance VIA Nano processor. The ART-3000's
system is designed with rugged aluminum alloy. It features a wall/VESA/
table-mountable design for easy installation. Its also support dual-sided
multiple connectors and has a wide range DC power input supporting AT
and ATX mode.

Specifications:

CPU: VIA Nano 1.3 GHz processor (800 MHz FSB)
•
System Chipset: VIA VX800 Unified Digital Media IGP
•
System Memory:
•
1 x DDR2 533/667 MHz SDRAM SODIMM slot
•
• Supports memory sizes up to 2 GB
VIA Chrome™ 9 HC3 DX9 3D/2D IGP
• Display:
Supports MPEG-2, H.264 and WMV9 Decoding
•
Support Dual Channel 24-bit LVDS panel
•
Dual Independent Display
•
Storage:
•
1 x 2.5-inch SATA hard disk bay
•
1 x CompactFlash disk (Type I/II) socket
•
• Audio: VIA VT1708B High Definition Audio Codec
BIOS: Award BIOS ( 8Mbit SPI Flash )
•
Front I/O:
•
2 x USB 2.0 ports
•
4 x COM ports (RS-232 and RS-232/422/485)
•
7V~36V DC-In power connector
•
Rear I/O:
•
2 x USB 2.0
•
• 1 x VGA connector
• 2 x LVDS connector
Step 2
Remove the screws on right and left side of the chassis.
Step 3
Lift up the chassis top cover.
2 x RJ45 port (Gigabit Ethernet connection)
•
2 x Audio jacks (Line-out and Mic-in)
•
Power Input Voltage: DC 7V ~ 36V
•
Power Consumption: Typical 18.5 W, Max. 25.8 W
•
• Dimensions: 233 mm (W) x 65.2 mm (H) x 123.5 mm
(D)
Net Weight: 1.5 Kg (3.3 lbs)
•
Operating Temperature:
•
With CompactFlash disk only: -20°C ~ 60°C
•
With 2.5-inch hard disk drive: 0°C ~ 45°C
•
• Humidity: 0% ~ 90% relative humidity (non-
condensing) @ 45°C
Vibration loading during operation:
•
CompactFlash = 5Grms
•
• 2.5-inch hard disk drive = 1Grms
• Shock during operation:
CompactFlash = 50G
•
Hard disk drive = 20G
•
EMC Approved: CE/FCC Class A
•

Packing List:

1 x ART-3000 unit
•
1 x SATA cable
•
1 x SATA power cable
•
1 x Power cable, 2-pole Phoenix plug to DC-jack
•
1 x 0.5cc Thermally Conductive Dispensable Gel in tube syringe
•
1 x Memory heatsink
•
Important:
Please ensure that all items in the packing list are present before
using this product. If any of the items are missing or damaged,
contact your distributor or sales representative immediately.

Installing the Memory

2
Step 1
First remove the hard disk brackets by unscrewing the four screws.
Step 2
Unscrew the four screws in order to remove the hard disk plate to
locate the memory heatsink.

Front I/O Layout

Item Description Item Description
1 Power button (Power On/Off) 6 COM4 port (RS-232)
2 Power input connector 7 COM3 port (RS-232)
3 USB 2.0 port 1 (USB1) 8 COM1 port (RS-232/422/485)
4 USB 2.0 port 2 (USB2) 9 Power LED indicator
5 COM2 port (RS-232/422/485) 10 HDD LED indicator

Rear I/O Layout

Item Description Item Description
11 Line-out jack 16 CompactFlash slot
12 Mic-in jack 17 LVDS port 1 (LVDS1)
13 USB 2.0 port 3 (USB3) 18 LVDS port 2 (LVDS2)
14 USB 2.0 port 4 (USB4) 19 RJ-45 Gigabit Ethernet LAN port 2 (LAN2)
15 VGA port 20 RJ-45 Gigabit Ethernet LAN port 1 (LAN1)
Step 3
Unscrew the two screws to remove the memory heatsink in order to
locate the memory slot.
Step 4
Insert the memory module into the SODIMM socket at the 45 degree
angle. Then push down until the memory module snaps into place. The
SODIMM socket has two locking mechanisms that will click once the
memory module has been fully inserted.