Bosch B465 Quick Start Manual page 2

2.9 | Insert the cellular module (optional)
Insert the cellular module into the slot of the B465 until the
module "clicks" into place. Refer to Figure 2.9.
1 2
MODULE 1
Y X
MODULE
RELEASE
COMMUNICATION MODULE 1
ETHERNET
100BASE-T
3
LINK
USB
TRBL
SYSTEM TROUBLE
TX TX
SDI2 RX RX
POWER PWR
Device Bus
R Y G B BATTERY BAT
INPUTS
2.2 k End of
24 VDC Line Resistors
or
16.5 VAC 1 COM 2 3 COM 4 PANEL PANEL
BATTERY LINE 1 LINE 2
16.5VAC + BAT - NC C NO C NO C NO 12V 1 COM 2 3 COM 4 T R PNL LINE 2 T R
RELAY 1 RELAY 2 RELAY 3 AUX COM PNL LINE 1
Figure 2.9: Insert the cellular communication module
Callout ― Description Callout ― Description
1 ― B44x cellular module 3 ― B465
2 ― Antenna
2.10 | Wire to the control panel
Refer to the enclosure wiring label supplied with the B465, or
the B465 Installation and Operation Guide for specific wire routing
information. Refer to Figure 2.10 for basic wiring routes.
MODULE 1
Y X
MODULE
RELEASE
COMMUNICATION MODULE 1
ETHERNET
100BASE-T
1
LINK
USB
SYSTEM TROUBLE
TX TX
RX
SDI2
POWER
Device Bus PWR
R Y G B BATTERY
INPUTS
2.2 k End of 2
24 VDC
Line Resistors
or
PANEL PANEL
16.5 VAC 1 COM 2 3 COM 4
BATTERY LINE 1 LINE 2 3
+ - T R T R
16.5VAC NC C NO C NO C NO 12V 1 COM 2 3 COM 4
BATTERY RELAY 1 RELAY 2 RELAY 3 AUX COM PNL LINE 1 PNL LINE 2
+ _
10
9 8 7 6 5 4
Figure 2.10: System wiring
Callout ― Description Callout ― Description
1 ― RJ 45 Ethernet 6 ― 12V AUX/COM terminals
connection to central station (optional output power source,
Special Application 9.9 - 13.8 V)
2 ― External Annunciator 7 ― Programmable output relays
(Relay 1, Relay 2, Relay 3)
terminal (connected to B46)
3 ― To tamper switch 8 ― Battery (7-18 Ah)
4 ― Phone Line 1/2 to control 9 ― To earth ground
panel terminals
16.5 VAC or 24 VDC power
5 ― EOL input loop 10 ―
supply input terminals
2.11 | Earth ground wiring
Connect the system to earth ground before making other
connections. Doing so prevents damage from electrostatic
discharges or other transient electrical surges. Use a
recommended earth ground reference such as a grounding
rod, or a cold water pipe. Make the connection using 14
AWG (1.8 mm) to 16 AWG (1.5 mm) wire. Refer to the B465
Installation and Operation Guide (P/N: F01U311207).
NOTICE!
The D8004 is required for any Commercial Fire
installations that use a plug-in transformer.
2.12 | Wire to the control panel
Use supporting wiring when connecting a B465 to a intrusion/
fire control panel in order to establish communication. Refer to
Figure 2.11.
3
1
RX
AC
BATTERY
INPUTS
2.2 k End of
Line Resistors
PANEL PANEL
1 COM 2 3 COM 4
LINE 1 LINE 2
1 COM 2 3 COM 4 PNL LINE 1 PNL LINE 2
2 T R T R
Figure 2.11: System wiring
Callout ― Description Callout ― Description
1 ― B465 module 3 ― Intrusion/Fire control panel
2 ― Phone wiring connection
2.13 | Wire to B46 (optional)
Use supporting B46 cable to connect to the B465. Refer to
Figure 2.12.
1
2
MODULE 1
Y X
MODULE
RELEASE
COMMUNICATION MODULE 1
ETHERNET
100BASE-T
LINK
USB
SYSTEM TROUBLE 3
TX TX
RX
SDI2
POWER PWR
Device Bus
R Y G B BATTERY
INPUTS
2.2 k End of
24 VDC Line Resistors
or
PANEL PANEL
16.5 VAC BATTERY 1 COM 2 3 COM 4
LINE 1 LINE 2
+ -
C NO 12V 1 COM 2 3 COM 4 T R T R
16.5VAC NC C NO C NO
BATTERY RELAY 1 RELAY 2 RELAY 3 AUX COM PNL LINE 1 PNL LINE 2
Figure 2.12: B46 wiring
Callout ― Description Callout ― Description
1 ― B465 module 3 ― B46 wiring harness (P/N:
F01U310747)
2 ― B46 module
3 | Configuration
You can configure the B465 using USB. For information on
configuring the B465, refer to the B465 Installation and Operation
Guide (P/N: F01U311207).
4 | LED descriptions
The B465 and B46 modules include on-board LEDs to assist
with troubleshooting issues as well as communication status.
For detailed information on all LED descriptions, refer to the
B465 Installation and Operation Guide (P/N: F01U311207).
7 | Certifications
Region Certification
US FCC Part 15 Class B
NIST FIPS 197 AES Certification (IP Communications)
California State Fire Marshall (CSFM)
UL 365 – Police Station Connected Burglar Alarm Units and
Systems
UL 609 – Local Burglar Alarm Units and Systems
UL 864 – Control Units and Accessories for Fire Alarm Systems
UL 985 – Household Fire Warning System Units
UL 1023 – Household Burglar Alarm System Units
UL 1076 – Proprietary Burglar Alarm Units and Systems
UL 1610 – Central Station Burglar Alarm Units
Canada CAN/ULC S303 – Local Burglar Alarm Units and Systems
CAN/ULC S304 – Signal Receiving Centre and Premise Alarm
Control Units
ULC - S545 – Residential Fire Warning System Control Units
ULC – ORD C1023 – Household Burglar Alarm System Units
ULC – ORD C1076 – Proprietary Burglar Alarm Units and Systems
ICES – 003 – Digital Apparatus
8 | Specifications
Dimensions 79 mm x 128 mm x 38 mm (3.11 in x 5.03 in x 1.50 in)
Voltage output 12 VDC nominal (Special application)
(operating)
Standby battery *Battery input: B465: Idle 150 mA; Alarm 230 mA
current Alarm: B465 with B440/B441/B442/B443 = 180 mA
requirements
24 VDC input *24 VDC input: B465: Idle 120 mA; Alarm 160 mA
current
requirements
USB cable USB cable (Type A to A male-to-male) - not supplied.
Use a Bosch supported cable such as the B99 cable
(F01U278853)
Compatible D1640, 120 VAC input, 16.5 VAC, 40 VA output Class 2
transformers plug-in
D1640-CA 120 VAC input, 16.5 VAC, 40 VA output Class
2 plug-in
D1640-120WI, 120 VAC input, 16.5 VAC, 40 VA output
Class 2 wire-in
Compatible Contact ID
digital dialer Pulse 3/1, Pulse 4/2
formats SIA (SIA8, SIA20)
Compatible D6600/D6100IPv6/D6100i
receivers
Compatible B10/B10R Medium Control Panel Enclosure
enclosures B11/B11R Small Control Panel Enclosure
D8103 Enclosure
Compatible B46 module (must use supporting B46 cable to connect
module to the B465)
Relative Up to 93% non-condensing
humidity
Temperature 0° to +49° C (+32° to 120° F)
(operating)
*Refer to the Standby battery requirements and calculations section in the
B465 Installation and Operation Guide for the current draw requirements of
other system components
Copyright
Use the serial number located on the product label and refer to the Bosch Security
Systems, Inc. website at http://www.boschsecurity.com/datecodes/.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security
Systems, Inc. website at http://www.boschsecurity.com/datecodes/.
Conettix Universal Dual Path
Communictor
B465
en Quick Start Guide
Bosch Security Systems, Inc. Bosch Sicherheitssysteme GmbH
130 Perinton Parkway Robert-Bosch-Ring 5
Fairport, NY 14450 85630 Grasbrunn
USA Germany
www.boschsecurity.com
© 2015 Bosch Security Systems, Inc. F.01U.311.091 | 03 | 2015.09