Related Manuals for elektraLite eyeBall IP65
Summary of Contents for elektraLite eyeBall IP65
-
Page 1: User Manual
Elektralite eyeBall IP65 Warm White USER MANUAL Elektralite (a division of Group One), 70, Sea Lane, Farmingdale, NY11735, U.S.A. T. +1 (631)-396-0184. F. +1 (631)-396-0190 WWW.MYELEKTRALITE.COM... -
Page 2: Safety Instructions
Always disconnect the eyeBall IP65 from the power source, when the device is not in use or before cleaning it. Only unplug eyeBall IP65 from the power cord. Never pull out the plug out by pulling on the power cord. -
Page 3: General Guidelines
As a result the fins and the surrounding area should be "open" all around the fixture. Do not block the fixture into a tight location. For example, do not try to mount the eyeBall IP65 like a "high hat" in a soffit surrounded by insulation;... - Page 4 “bad” connection and other fixtures in the same circuit. DMX 512 CONTROL: The eyeBall IP65 come with a 5 pin XLR connector to an outdoor water resistant 3 pin connector cable. Extension cables (water resistant connector to water resistant connector) are available as accessories.
-
Page 5: Run Mode
OFF, DIM1, DIM2, DIM3, DIM4 NTSC or PAL 9. Static Look. The eyeBall IP65 can be set to a single static look quickly. Use the Menu button to get to STAT. Press Enter. The next screen will read W.000. This is addressing the warm white leds. - Page 6 11. DMX 512 Setting (address). Sets up the address for the dmx. Using the Menu button in the root menu go to DMX Press Enter to get into DMX menu and the display will read the current dmx channel. The display will read for example d.001 This means the fixture's current address is 001 To change it, use the ↑...
- Page 7 Using the Menu button, go through the Root Menu until Set. Press Enter and then use the ↑ or ↓ buttons to get to DIM. Press Enter and then use the ↑ or ↓ buttons to get to the DIM choice required. Once chosen, press Enter to save it and then use the Menu button to exit back to the root directory.
- Page 8 16. The Personalities of the WW eyeball IP65. 0-255 Warm White Dimmer 0-255 Warm White Dimmer 0-50 Linear dimmer speed（DIM=OFF） 51-100 nonlinear speed1（DIM1） 101-150 nonlinear speed 2（DIM2） 151-200 nonlinear speed 3（DIM3） 201-255 nonlinear speed 4（DIM4） 0-255 Warm White Dimmer No Function...
-
Page 9: Dmx Channel Assignments
17. DMX Channel Assignments. Depending on the Personality chosen, the eyeBall IP65 can be 1, 2, 3 or 4 channels. Personalities:- W = 1 channel (the first channel listed below) Wd = 2 channels (the first two channels listed below) WS = 3 channels (the first three channels listed below). -
Page 10: Cleaning And Maintenance
The clear front glass cover for the lenses should be cleaned so the light output is maintained. With the elektraLite eyeBall IP65 turned off, use only a moist lint-free cloth, and clean the glass cover. Never use alcohol or solvents to clean the fixture. Never spray anything onto the fixture at the front or in any place on the fixture. - Page 11 Other Products. Elektralite has other great products that are manufactured under the Elektralite product line. Go check out the website at www.myelektralite.com A preview of the products include:- Elektralite Audience Blinder Elektralite Elektrabar with glare shield for perfect cuts Utilizing homogenized 6-in-1 leds. RGBWAI where the I is indigo (not UV) ; this way perfect pastels like...
- Page 12 The Elektralite 1018 Using 18 high powered 12 watt leds, the Elektralite 1018 is available using 4-in-1 or 6-in-1 leds. Each led can produce any combination of colors as each led is either an RGBW or RGBWAI device Elektralite ML602 The ML902 utilizes a 120 watt Led and is brighter than a 250 discharge light source.
Need help?
Do you have a question about the eyeBall IP65 and is the answer not in the manual?
Questions and answers