Related Manuals for Kettler 7199-200
Summary of Contents for Kettler 7199-200
- Page 1 KETTLER CAVALIER OUTDOOR FOOSBALL TABLE Model 7199-200 Adult Assembly Required Made in Italy Picture Similar KETTLER® International Inc. • 1355 London Bridge Road • Virginia Beach, VA 23453 USA www.kettlerusa.com info@kettlerusa.com 1 reqd.
- Page 2 • • Do not use the foosball table until it has been Waste disposal: KETTLER® products are fully and correctly assembled and checked. recyclable. At the end of its useful life, please • dispose of correctly and safely complying with Set the table up on a level surface.
- Page 3 Number Included-1 Number Included-2 Number Included-1 Number Included-5 Number Included-2 Number Included-8 Number Included-2...
- Page 4 Number Included-8 (M8x40 Carriage Bolt) Number Included-8 Number Included-8 Number Included-8 (M8 Lockwasher) (M8 Hexnut) Number Included- Number Included- 2 Blue 10 Blue Number Included-6 Number Included-44 2 Silver Number Included-4 10 Silver (M2.8 X 11.5 Screw) (M4 X 25 Screw) (M3.9X35 Screw) Number Included-8 Number Included-4...
-
Page 5: Leg Assembly
Step 1 2 each required 1 required 1 required 1 required Leg Assembly Place legs inside cabinet at an outward angle. Horizontal bar between legs should be toward table end. (A) Ensure holes in side of cabinet align with holes in leg. Insert two M8 x 40 Carriage Bolts from the outside in towards leg. - Page 6 Step 1 (continued) From inside of cabinet, place M8 Lockwashers then M8 hexnuts onto Carriage Bolt ends (E) and tighten (F). Screw floor leveler into leg post. (G) REPEAT STEP 1 A-G FOR EACH LEG IMPORTANT: Have two Step 2 people complete Step 2.
-
Page 7: Rod Assembly
Step 3 Rod Assembly 2 sets required The foosball table comes with 4 telescopic rods for each team. The bar scheme is as follows: Rod with 1 blue player (Goalie) Rod with 2 blue players (Defense) Rod with 3 silver players (Forwards) Rod with 5 blue players (Mid-Fielders) Rod with 5 silver players (Mid-Fielders) Rod with 3 blue players (Forwards) - Page 8 Step 3 (continued) Insert Blue Goalie into first rod holes at the end of table. Insert rod end without bushing by tilting rod as shown. Ensure that player faces direction of the arrow as shown. Insert the opposite end with bushing into rod hole lining pins with screw holes in cabinet.
- Page 9 REPEAT STEP 3 A-C FOR EACH ROD AS SHOWN BELOW Use the diagram on Page 6 for additional assistance. SKIP BALL DROP HOLE...
- Page 10 Step 4 May be necessary to complete before proceeding with Step 4 Rod Bushing Assembly 16 required 8 required 8 required M4 X 25 Insert the 2 part inner bushing in the open cabinet hole (which has the rod extending through) as shown.
- Page 11 Step 4 Rod Bushing Assembly (Continued) Using 2 of the M4 x 25 screws, fasten the bushing into place. REPEAT STEP 4 A-G FOR EACH ROD...
- Page 12 Step 5 Rod Bearing Assembly 16 required 8 required 8 required M4 x 25 On the opposite cabinet hole, slide bearing over the end of rod. (A,B) Insert the end cap into hole. Ensure that it is flush with the cabinet’s wall. (D) Using two M4x25 screws, fasten the end cap into place.
- Page 13 Step 6 8 required Rod Handle Assembly Place the rod handle onto the end of the telescopic rod. Lightly tap handle using a hammer until the handle end reaches the line on the rod closest to the table. (B) REPEAT THE STEP 6 A-B FOR EACH ROD...
- Page 14 Step 7 Ball Drop Assembly 3 required 1 required M2.8 x 11.5 Locate the ball drop assembly hole on the side of cabinet wall. It will be directly in the middle of table and will have 3 punched pilot holes surrounding it. (A) Place ball drop into the hole.
-
Page 15: Shroud Assembly
Step 8 Shroud Assembly 6 required 1 required M4 x 25 Place the shroud over the tables edge with the rounded edge pointed away from the table as shown. (A) Using the three M4 x 25 screws, fasten the front of shroud to table. -
Page 16: Counter Assembly
Step 9 Counter Assembly 2 required 10 required 2 required 1 required M3.9 x 35 Build blue and silver counters. Separate the two blue and two silver cubes with screw holes; these need to be installed at each end of the counter rods. - Page 17 FOOSBALL TABLE COVER The foosball table comes with a cover included when purchased. Always cover your foosball table when not using. This protects the table from the elements and increases the life of the product to provide many years of enjoyment! The cover is equipped with a Velcro side opening for ease of use and a tie down...
- Page 18 United States only. Any shipment outside of the United States will be at the sole cost of the customer. This KETTLER® Limited Warranty is a manufacturer’s warranty and is not changed or modified by additional warranties extended by individual retailers at the point of sale.
- Page 19 Log onto www.kettlerusa.com/warranty and register your KETTLER ® Cavalier Foosball Table Warranty online! www.facebook.com/kettlerusa www.youtube.com/kettlerusa twitter.com/kettler_usa...
- Page 20 All rights reserved. No part of this manual may be ® reproduced, stored in a retrieval system, or transmitted in any form, or by any means, such as electronic, mechanical, photocopying or otherwise, without the prior written permission of KETTLER ® KETTLER ®...