Table of Contents
Advertisement
Connection: Digital Media Recorder + TV + Cable Box
1. Connect the 2 Way Splitter (provided) to split the cable signal
2 Way Splitter
(provided)
RF Coaxial cable
2. Connect the VCR to the TV (optional)
3. Connect the Digital Media Recorder to the TV
Audio video cables are
usually color-coded red,
white, and yellow.
S-Video cable
4. Attach the AC power cord to the unit.
5. Insert the the other end of the AC power cord into an AC outlet (or power strip).
Component video cables
are sometimes color-
coded red, green, and
blue. You can also use
three standard video
cables (usually color-
coded yellow).
Note: Before you connect the Digital Media Recorder, you'll need to disconnect some of the cables first in order
to re-connect them.
1a.
Disconnect the RF Coaxial cable that originates from the cable signal coming into your house, and goes
to the cable box. Connect this RF Coaxial cable to the 2 Way Splitter that was packed with your Digital Media
Recorder — connect the cable to the end of the 2 Way Splitter that has only one connector.
1b.
Use the RF Coaxial cable that was packed with your Digital Media Recorder, and connect one end to the
2 Way Splitter — connect the cable to the end that has two connectors (it doesn't matter which of the two
connectors you use). Connect the other end of this cable to the Cable Signal Input jack on the cable box.
1c.
Connect another RF Coaxial cable to the cable box's TV Output Jack (sometimes labeled OUT TO TV); and
connect the other end to the RF ANTENNA/CABLE INPUT jack on the back of the Digital Media Recorder.
1d. Connect another RF Coaxial cable to the other connector that's available on the 2 Way Splitter. Connect
the other end of that cable to your VCR's Antenna Input jack (sometimes labeled CABLE/ANTENNA IN). If
you're NOT connecting a VCR, go to 1e.
1e.
Connect another RF Coaxial cable to the other connector that's available on the 2 Way Splitter. Connect
the other end of that cable to your TV's Antenna Input jack (sometimes labeled CABLE/ANTENNA).
For more information about the other Input jacks on the back of the Digital Media Recorder, go to page 54.
If you connected a VCR (step 1d above), connect one end of an RF Coaxial cable to the VCR's Output jack
(sometimes labeled OUT TO TV) and the other end to the TV's Input jack (sometimes labeled CABLE/ANTeNNA).
If you didn't connect a VCR, skip this step and proceed to step 3.
You need to connect cables to the Digital Media Recorder's OUTPUT jacks to the TV's INPUT jacks in order to
see the content from the Digital Media Recorder (whether it's a TV program, something you recorded to the
hard disk drive, or a disc you're playing).
3a. Connect the audio cables.
A set of audio/video cables was packed with your Digital Media Recorder. Connect the audio cables to the
OUTPUT AUDIO L (left – white) and R (right – red) jacks on the back of your Digital Media Recorder, and
to the corresponding Audio Input jacks on your TV (sometimes labeled AUDIO IN L and R).
3b. Connect the video cable. The cables you use for the video determine the quality of the picture you'll see on
your TV when you're playing DVDs. For more information about cables and signal quality, go to page 56.
Good: Connect the video cable (yellow) to the OUTPUT COMPOSITE VIDEO jack on the back of your Digital
Media Recorder, and to the Video Input jack on your TV (sometimes labeled VIDEO IN)
3c. Better: If your TV has an S-VIDEO jack, connect one end of the S-Video cable (provided) to the S-VIDEO
jack on the back of the TV and the other end to the OUTPUT S-VIDEO jack on the back of the Digital
Media Recorder.
3d. Best: If your TV has Component Input Jacks (Y, Pb, Pr), you can achieve even greater picture quality by
connecting the Digital Media Recorder to the TV using these jacks (COMPONENT VIDEO OUTPUT, Y, Pb, Pr
on the Digital Media Recorder). For more explanation, go to page 56.
Note: If your TV is capable of progressive scan, connect the Digital Media Recorder to the TV using the
COMPONENT VIDEO OUTPUT jacks (see 3d above), and slide the PROG SCAN switch to the ON position to see
DVD titles (movies) in progressive scan format. If you need more explanation, go to page 55.
Notes: This connection enables you to watch one channel while you record another channel to the Digital Media
Recorder's hard disk drive by splitting the cable signal. If your cable box is necessary for premium channels, you
won't be able to access them when watching TV directly (i.e., without going through the Digital Media Recorder
by tuning the TV to its VIdeo Input Channel).
Chapter 1: Connections and Setup
OR
OR
Go to page 11
7
Advertisement
Table of Contents
