Advertisement
Table of Contents
- 1 Mechanic Troubleshooting
- 2 Handlebar/Seat Post Horizontal Slider Moves While Closed
- 3 Handlebar Stem Wobbles / Twist
- 4 Unusual Noise
- 5 Slack in Drive Gear
- 6 Seat Post Does Not Move Vertical When Lever Is Open
- 7 Seat Post Does Not Maintain Vertical Position During Exercise (Sinks in When Lever Closed)
- Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Indoor Cycling IC7
Summary of Contents for Indoor Cycling IC7
- Page 1 IC7 Indoor Cycle MECHANIC TROUBLESHOOTING _________________________________________________________________________________ FB TS ME7 01 ICG® Standard Operating Procedure | released by ICG® Service Department 1 ...
- Page 2 HANDLEBAR/SEAT POST HORIZONTAL SLIDER MOVES WHILE CLOSED Top slider does not remain in set position Adjust the flip lever using a 25 torx Open and close lever a couple and check freely moving of the slider while lever is open Horizontal slider remains in position Repeat adjustment while lever is closed and process freely moving while lever opened? Problem solved _________________________________________________________________________________ FB TS ME7 01 ICG® Standard Operating Procedure | released by ICG® Service Department 2...
- Page 3 HANDLEBAR STEM WOBBLES / TWIST Handlebar stem wobbles / twist Adjust the handlebar stem flip lever using a round head allen key 2.5mm Open and close Flip lever a couple and check freely sliding of the HB stem and twist of HB stem Twisting Repeat adjustment reduced process Problem solved _________________________________________________________________________________ FB TS ME7 01 ICG® Standard Operating Procedure | released by ICG® Service Department 3...
- Page 4 UNUSUAL NOISE Noise appears during use of the bike Remove right Check toestrap lock shroud and check facing outside the Clicking noise Categorize noise Grinding noise (below 50 RPM) no cables touching pedal flywheel and place right if necessary Squeeking noise at low RPM < 20 Noise still appears? Noise still appears? Remove right shroud and Check belt tension and adjust if necessary Noise Replace generator Check pedal torque generator appearance at? Art No: 150-01-00017-01 value (45Nm) Flywheel hub bearings Noise still idler pulley primary drive appears? BB bearings Noise still ...
- Page 5 SLACK IN DRIVE GEAR Slack in drive gear Slack in drive gear recognized while rocking on horizontal pedals Remove right shroud and check belt tension and adjust if necessary Replace primary belt Slack still occur Art No: 150-03-00045-01 Problem solved _________________________________________________________________________________ FB TS ME7 01 ICG® Standard Operating Procedure | released by ICG® Service Department 5...
- Page 6 SEAT POST DOES NOT MOVE VERTICAL WHEN LEVER IS OPEN Seat post does not move vertical when lever is open Remove gas damper bracket cover on the bottom of the main frame using a 3.0mm allen key Check bowden cable fitment on ferrale While vertical adjustment lever is closed the engagement lever located at the gas damper mounting head should provide a slight play Turn ferrale counterclockwise Open vertical adjustment to test seat post easily extending and compressing Extending and Problem solved compressing easily? _________________________________________________________________________________ FB TS ME7 01 ICG® Standard Operating Procedure | released by ICG® Service Department 6...
- Page 7 SEAT POST DOES NOT MAINTAIN VERTICAL POSITION DURING EXERCISE (SINKS IN WHEN LEVER CLOSED) Seat post does not maintain vertical postion during exercise (sinks in when lever closed) Remove damper bracket on the bottom of the main frame using a 3.0mm allen key Check bowden cable fitment on ferrale Perform loadtest: extend saddle, mark tube, apply load on seat post to recognize If Seat post sinks While vertical adjustment flip lever is closed the engagement lever located at the gas damper mounting head should provide a slight play Turn ferrale clockwise Open vertical Close lever and adjustment to test apply load to Seat Seat post still seat post easily post to check seat sinks extending and ...
Need help?
Do you have a question about the IC7 and is the answer not in the manual?
Questions and answers
Le levier de réglage en hauteur de la scelle du IC7 ne se fixe plus et laisse la scelle tomber lors d’un effort intense. La résistance du levier semble avoir disparu .
Adjust the flip lever using a 25 Torx key. Open and close the lever a few times to check if the saddle slider moves freely when the lever is open. If the slider does not stay in position, repeat the adjustment while the lever is closed. If the issue persists, further inspection or servicing may be needed.
This answer is automatically generated
How can I adjust the Shimano pedal release pressure?