Summary of Contents for DBI SALA ExoFit NEX 1113283
Page 1
ExoFit NEX™ Full Body Suspension Harness Model Numbers: 1113575 1113575C 1113663 1113663C 1113283 1113283C 1113576 1113576C 1113664 1113664C 1113284 1113284C 1113577 1113577C 1113665 1113665C 1113289 1113289C 1113578 1113578C 1113666 1113666C 1113304 1113304C The Ultimate in Fall Protection 1113579 1113579C 1113667 1113667C 1113348 1113348C...
Page 2
1.0 application 1.1.1 purpose: Suspension harness used for Fall Figure 2 - applications Arrest (D-Ring connections A, Figure 2) and Work Positioning (D-Ring connections B, Figure 2). 1.2.1 standards: Refer to life safety harness information found in NFPA 1500, Standard on Fire Department Occupational Safety and Health Program, and NFPA 1983, Standard on Life Safety Rope and Equipment for Emergency Services.
Figure 3 - donning suspension harness step 1 step 3 step 2 duo-lok™ Quick Connect Buckles Connection: Connect buckle ends by inserting the tab into the receptor until a click is heard. strap adjustment: Rotate Webbing Lock to unlocked position .
3.10 donning and Fitting the Fire and resCue harness. The Fire and Rescue Harness can be used for work positioning or for rescue worker applications. The Class II harness assembly must be donned appropriately for the specific application. After the Class II harness has been donned for work positioning or for rescue, the Class III portion of the harness can be donned. See Section 3.11 for work positioning, Section 3.12 for rescue and 3.13 for the shoulder straps.
Page 5
step 5. Grasp the waist-level strap ends on right and left sides of the harness. Pull both ends forward until all slack is removed from the waist strap and the strap is comfortably tight around your waist. Insert strap ends into the waist strap keeper loops on the right and left sides of the harness.
Page 6
3.13 shoulder straps: Complete donning of the ExoFit NEX™ Fire Rescue Class III harness by following Figure 6, Steps 1 through 6. Figure 6 - Fire and rescue harness shoulder strap donning step 2 step 1 step 3 step 5 step 6 step 4 Figure 6...
Page 7
step 6. Confirm that the back straps are secured by the carabiners (a - blue strap end secured by carabiner to blue loop; B - red strap end end secured by carabiner to red loop) and that the straps lie flat across your back. The D-Ring at the center of the harness padding between your shoulders must be facing outward and free to swivel up and down. Adjust shoulder straps to a snug fit.
ExoFit NEX™ Full Body Harness Model Numbers: (See back pages.) USER INSTRUCTION MANUAL EXOFIT NEX™ FULL BODY HARNESS This manual is intended to meet the Manufacturer’s Instructions as required by ANSI Z359 and CSA 259.10 and should be used as part of an employee training program as required by OSHA WARNING: This product is part of a personal fall arrest, restraint, work positioning, climbing, controlled descent, or rescue system.
Page 9
Figure 1 - ExoFit NEX™ Vest Style Full Body Harness A. Shoulder Strap w/Hybrid Padding B. Duo-Lok™ Quick Connect Buckle C. Chest Strap D. Hybrid Chest Pad with i-Safe™ RFID Tag & Labels E. Revolver™ Torso Adjustor F. Tech-Lite™ Side D-Ring G. Leg Strap H. Tech-Lite™ Dorsal D-Ring I. Trauma Strap Figure 2 - ExoFit NEX™...
Page 10
1.0 APPLICATION PURPOSE: The DBI-SALA ExoFit NEX™ Full Body Harness (Figure 1 and Figure 2) should be used as a component ™ in personal fall arrest, restraint, work positioning, climbing, controlled descent, or rescue systems (see Table 1). ExoFit NEX™ Harnesses included in this manual are full body harnesses and meet ANSI Z359.1, OSHA, and CSA Z259.10 requirements.
Page 11
Figure 3 - Applications Fall Arrest Restraint Ladder Climbing Work Positioning Work Positioning or Controlled Descent, with Seat Sling Work Positioning, with Seat Sling Work Positioning, with Seat Sling - Tower Climbing Anchorage Anchorage Connector Connecting Subsystem (SRL shown) D Full Body Harness Restraint Lanyard Backup Fall Arrest System...
Page 12
Figure 4 - Fall Clearance (Lanyards) Figure 5 - Swing Falls RD = LL + DD + HH + C Required Fall Clearance Distance Length of Lanyard (Specifi ed on labeling) Deceleration Distance = 4 ft (1.2 m) except: • for ANSI/OSHA Lanyards with Free Fall greater than 6 ft (1.8 m) up to 12 ft (3.7 m), or user weights greater than 310 lbs (141 kg) up to 420 lbs (191 kg);...
Page 13
MAKING CONNECTIONS: Use only self-locking snap hooks and carabiners with this equipment. Only use connectors that are suitable to each application. Ensure all connections are compatible in size, shape and strength. Do not use equipment that is not compatible. Ensure all connectors are fully closed and locked. DBI-SALA connectors (snap hooks and carabiners) are designed to be used only as specifi...
Page 14
2.10 CONNECTING SUBSYSTEMS: Connecting subsystems (self-retracting lifeline, lanyard, rope grab and lifeline, cable sleeve) must be suitable for your application (see Table 1). See subsystem manufacturer’s instructions for more information. Some harness models have web loop connection points. Do not use snap hooks to connect to web loops.
Page 15
3.0 DONNING AND USE WARNING: Do not alter or intentionally misuse this equipment. Consult Capital Safety when using this equipment in combination with components or subsystems other than those described in this manual. Some subsystem and component combinations may interfere with the operation of this equipment. Use caution when using this equipment around moving machinery, electrical and chemical hazards, and sharp edges.
Page 16
EXOFIT NEX™ VEST STYLE FULL BODY HARNESS: The ExoFit NEX™ Vest Style Harness incorporates loops for a removable waist belt (see Figure 9). The belt can be installed through the two loops in the harness located in the lower back shoulder straps. The belt will pass through the harness just below the padded area.
Figure 11 - Donning the ExoFit NEX™ Vest Style Full Body Harness Step 1 Step 2 Step 3 Duo-Lok™ Quick Connect Buckles Connection: Connect buckle ends by inserting the tab into the receptor until a click is heard. Strap Adjustment: Rotate Webbing Lock to unlocked position .
Page 18
EXOFIT NEX™ CROSS-OVER STYLE FULL BODY HARNESS: The ExoFit NEX™ Cross-Over Style Harness incorporates loops for a removable waist belt. The belt can be installed through the two loops in the harness located in the lower back shoulder straps (see Figure 10). The belt will pass through the harness just below the padded area.
Figure 12 - Donning the ExoFit NEX™ Cross-Over Style Full Body Harness Step 1 Step 2 Step 3 Duo-Lok™ Quick Connect Buckles Connection: Connect buckle ends by inserting the tab into the receptor until a click is heard. Strap Adjustment: Rotate Webbing Lock to unlocked position .
Page 20
SUSPENSION TRAUMA STRAP: The Figure 13 - Suspension Trauma Straps ExoFit NEX™ Full Body Harness is equipped with a Suspension Trauma Strap (Figure 13) to help prolong allowable suspension time in the event of a fall from height. It should only be used in situations where a fall has occurred or for training.
Page 21
4.0 TRAINING It is the responsibility of the purchaser and the user of this equipment to assure that they understand these instructions and are trained in the correct care and use of this equipment. They must also be aware of the operating characteristics, application limits, and the consequences of improper use of this equipment.
Page 22
Step 5. Record inspection data: Record the inspection date and results in the Inspection and Maintenance Log (see Section 9). Step 6. Inspect the Stitched Impact Indicator: The stitched impact indicator is a section of webbing that is lapped back on itself and secured with a specifi c stitch pattern holding the lap (see Figure 16).
Page 23
7.0 SPECIFICATIONS PERFORMANCE: • Maximum Free Fall Distance: No greater than 6 ft (1.8 m), per federal law and ANSI Z359.1. NOTE: Harness is acceptable for use with free fall distances exceeding 6 feet (1.8 m) if used with appropriate connecting system. •...
Page 24
9.0 INSPECTION AND MAINTENANCE LOG SERIAL NUMBER: MODEL NUMBER: DATE PURCHASED: DATE OF FIRST USE: INSPECTION DATE INSPECTION ITEMS CORRECTIVE ACTION MAINTENANCE NOTED PERFORMED Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By:...
Page 25
INSPECTION AND MAINTENANCE LOG SERIAL NUMBER: MODEL NUMBER: DATE PURCHASED: DATE OF FIRST USE: INSPECTION DATE INSPECTION ITEMS CORRECTIVE ACTION MAINTENANCE NOTED PERFORMED Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By:...
Page 26
INSPECTION AND MAINTENANCE LOG SERIAL NUMBER: MODEL NUMBER: DATE PURCHASED: DATE OF FIRST USE: INSPECTION DATE INSPECTION ITEMS CORRECTIVE ACTION MAINTENANCE NOTED PERFORMED Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By:...
Need help?
Do you have a question about the ExoFit NEX 1113283 and is the answer not in the manual?
Questions and answers