Quick Channel Select; Using Two Group Scan Or Two Open Scan Modes; Selective Calling; Selcall Indentification Number (Ident) - GME TX3350 Instruction Manual

NOTE:
In Group Scan mode you can also treat the Priority
Channel as a nuisance channel and remove it from the scan
session, but if you do, you will no longer be monitoring the
Priority Channel while scanning. However if you press the PTT
you will still be taken straight to the Priority Channel when
required to converse on that channel. After your conversation
has finished the scan will continue without the Priority
Channel included.

QUICK CHANNEL SELECT

To quickly review or edit channels stored in the current scan
memory, briefly press the
keys to manually step through the stored scan channels.
Only those channels that have been stored in the current
scan group memory will be displayed. During this time 'F' will
remain on the display to confirm you are still in 'Quick Select'
mode. To exit this mode, press the
10 seconds for the function to time out.
USING TWO GROUP SCAN OR TWO OPEN
SCAN MODES
If you prefer, the TX3350 can be re-programmed to have two
Group Scan modes or two Open Scan modes instead of one
of each.
Your TX3350 can be retailer programmed to convert the
Group Scan mode into a second Open Scan mode and vice
versa. If you would prefer to have two Group Scan or two
Open Scan modes, you should contact your GME retailer to
arrange for this feature to be enabled (when using two Group
Scan modes the Priority Channel will be the same channel for
both scan groups).
When the second Open or Group Scan mode is enabled, the
resulting two Scan modes become Scan 1 and Scan 2.
To select the required Scan Mode
Press the key followed by the
'Scan 2' will be displayed to confirm your selection. When
enabled, the two scan modes will be identical in operation.
NOTE: Enabling or disabling the second Open or Group Scan
mode is not a user selectable option. Once enabled by your
GME retailer, the changed Scan mode becomes a permanent
PA G E 1 4
key then press the
key again or wait
key. 'Scan 1' or
I N S T R U C T I O N M A N U A L
part of the TX3350's features and replaces the standard Scan
selection. If you find later that you need the original Group or
Open Scan function re-enabled, you will need to return your
TX3350 to your retailer for re-programming.

SELECTIVE CALLING

Your TX3350 has a Selective Calling system known as SelCall
that operates like a telephone. Your radio is pre-programmed
with its unique SelCall Identification Number. If this number is
called by another radio, your TX3350 will beep to alert you. If
you do not want to hear any other activity while waiting on a
or channel, you can select the Quiet mode. Your radio will then
remain quiet to all incoming signals until your SelCall number
is called.
Your TX3350 will allow you to store up to ten (10) most
frequently called SelCall numbers, with each number being
labelled for easy identification.
SELCALL IDENTIFICATION NUMBER (IDENT)
Your radio is factory programmed with its own unique SelCall
Identification Number (Ident). This number identifies your
radio from others. Your radio's own SelCall Ident will be
displayed for a few seconds in the lower left of the channel
display when you first turn your radio on. You will need to
make this Ident known to others who may need to call you
using SelCall.
NOTE:
Although your radio is factory-programmed with a
unique SelCall Ident, you can change your Ident to another
number if required (see SelCall Memories on next page).

SELCALL IDENT LABELS

When storing SelCall Idents, you can add labels to each one
to make it easier to identify whose Ident you are recalling. In
addition, if an incoming SelCall matches one of your stored
Idents, the label can be displayed instead of the Ident. To
add or display labels, your radio must be in the ALPHA mode.
To switch between ALPHA mode and Numeric Mode, briefly
press the
'NUMER' will be displayed briefly to the lower left of the
channel display to indicate the selected mode.
key followed by the key. 'ALPHA' or
T X 3 3 5 0