-20°C ~ 60°C (-4°F ~140°F) External dimension Length 158 mm,Height93 mm,Width 87mm Weight 580g (Except for Lithium lon Battery Pack and tape) Built-in MIC Omni-direcional stereo condenser microphone Remote control Indoors: greater than 15m (straight line) Outdoors:greater than 5m (straight line) Samsung Electronics...
Page 3
Product Specifications 1-2 Product Specifications (VP-D70/D70i) Design and specifications are subject to change without notice. Description Operation SYSTEM Video signal PAL, CCIR standards Video recording system 2rotary heads,helical scanning system Audio recording system Rotary heads, PCM system Usable cassette Digital video tape (6.35mm width): MiniDV cassette Tape speed SP : approx.
2. Disassembly and Reassembly 2-1 Cabinet and PCB 2-1-1 Top Cover removal (1) Remove 2 screws Fig. 2-1 Top Cover removal Samsung Electronics...
Page 7
Disassembly and Reassembly 2-1-2 Ass’y Cover Housing removal (3) Remove cover housing in the direction of arrow (1) Remove 2 screws (2) Remove 2 screws Fig. 2-2 Ass’y Cover Housing removal Samsung Electronics...
Page 8
Disassembly and Reassembly 2-1-3 Ass’y Front removal (1) Remove 1 screw (3) Remove ass’y front in the direction of arrow (2) Remove 1 screw Fig. 2-3 Ass’y Front removal Samsung Electronics...
Page 9
Disassembly and Reassembly 2-1-4 Ass’y Case-Left removal (2) Remove 2 screws (1) Remove 2 screws (5) Remove ass’y case left in the direction of arrow (3) Remove 2 screws (4) Remove 2 screws Fig. 2-4 Ass’y Case-Left removal Samsung Electronics...
Page 10
Disassembly and Reassembly 2-1-5 Ass’y Case-Right removal (1) Remove 2 screws (4) Remove ass’y case right in the direction of arrow (2) Remove 2 screws (3) Remove 1 screw Fig. 2-5 Ass’y Case-Right removal Samsung Electronics...
Page 11
Disassembly and Reassembly 2-1-6 Ass’y Camera & Main PCB removal (2) Remove ass’y camera & main pcb in the direction of arrow (1) Remove 3 screws Fig. 2-6 Ass’y Camera & Main PCB removal Samsung Electronics...
Page 12
Disassembly and Reassembly 2-1-7 Ass’y-Camera removal (2) Remove 1 screw (3) Remove ass’y camera in the direction of arrow (1) Desolder Fig. 2-7 Ass’y Camera removal Samsung Electronics...
Page 15
2. Disassembly and Reassembly 2-1 Cabinet and PCB 2-1-1 Top Cover removal (1) Remove 2 screws Fig. 2-1 Top Cover removal Samsung Electronics...
Page 16
Disassembly and Reassembly 2-1-2 Ass’y Cover Housing removal (3) Remove cover housing in the direction of arrow (1) Remove 2 screws (2) Remove 2 screws Fig. 2-2 Ass’y Cover Housing removal Samsung Electronics...
Page 17
Disassembly and Reassembly 2-1-3 Ass’y Front removal (1) Remove 1 screw (3) Remove ass’y front in the direction of arrow (2) Remove 1 screw Fig. 2-3 Ass’y Front removal Samsung Electronics...
Page 18
Disassembly and Reassembly 2-1-4 Ass’y Case-Left removal (2) Remove 2 screws (1) Remove 2 screws (5) Remove ass’y case left in the direction of arrow (3) Remove 2 screws (4) Remove 2 screws Fig. 2-4 Ass’y Case-Left removal Samsung Electronics...
Page 19
Disassembly and Reassembly 2-1-5 Ass’y Case-Right removal (1) Remove 2 screws (4) Remove ass’y case right in the direction of arrow (2) Remove 2 screws (3) Remove 1 screw Fig. 2-5 Ass’y Case-Right removal Samsung Electronics...
Page 20
Disassembly and Reassembly 2-1-6 Ass’y Camera & Main PCB removal (2) Remove ass’y camera & main pcb in the direction of arrow (1) Remove 3 screws Fig. 2-6 Ass’y Camera & Main PCB removal Samsung Electronics...
Page 21
Disassembly and Reassembly 2-1-7 Ass’y-Camera removal (2) Remove 1 screw (3) Remove ass’y camera in the direction of arrow (1) Desolder Fig. 2-7 Ass’y Camera removal Samsung Electronics...
3. When changing the adjustment item after the adjusted value is designated, press the "START/STOP" button. SP PLAY 0:00:00:01 NO MODE EVR EPR Indicates preset values 1 V-REF Indicates the adjusted values S64 LOO Indicates current adjustment item. 01 01380 Samsung Electronics...
Page 25
Fig.1. RIGHT CASE Fig.2. REMOCON KEY STEP 3 . If you want to finish the adjustment mode, you have to do Power Reset. The Power Reset means that you pull out the power source and pull in it again. Samsung Electronics...
Page 26
DUB REC CURRENT DUBCUR * MODELOPTION Model Adj.value Model Adj.value SC-D70 VP-D70 SC-D73 VP-D73 SC-D75 VP-D75 SC-D77 VP-D77 2. How to adjust Video-Reference (V-REF). 1) Connect video output cable to wave form scope. The wave form scope must be connected to monitor.
Page 27
1) Select ZOOMVR in the video adjustment mode. 2) Adjust ZOOM SW so that the switch is put in the middle of T and W. 3) Adjust ZOOMVR so that the current value of ZOOM SW is equal to the adjusted ZOOMVR value. Samsung Electronics...
3. Press the Address selection button(START/STOP button) to skip the next address in order to finish the adjustment and store data. After finishing the adjustment, you have to do power reset. The PRML BER will be set to the right adjustment when shipping out video camera and PCB ASSY from factory. Samsung Electronics...
Page 29
The optimum means the number error is less than 10 EA. ;Current SC-D70/VP- D70 manufacturing standard If the minimum value is as the followings, designate as the right values......................;Selection valueless iess than 18 ..................18 ;REG12===24A ......................19 ;REG12===26A ......................20 ;REG12===28A Samsung Electronics...
Page 30
......... ;REG24 ===FA2 6) Check the value is input to unit correctly. Samsung Electronics...
Page 31
2) Press the "START/STOP" button when storing confirmed adjustment value of each adjustment step in EEPROM. 3) There is a flicker on screen after finishing each adjustment step. 4) To clear the adjustment mode, pull out the power source. Samsung Electronics...
Page 32
5 seconds. 3) Set the "POWER(CAMERA/PLAY- ER)" switch to "CAMERA" position. STEP 3 4) The OSD appears. Monitor OSD shows "16D XX XX". Then camera adjustment mode has Note : "XX" indicates variable values. been activated successfully. Samsung Electronics...
Page 46
Adjustment Address SC-D67/70 VP-D70 NAME Samsung Electronics 3-23...
Page 47
5) Press the FF(Mode Up)/REW(Mode Down) button so that OSD shows "260 XX XX". 6) Press the START/STOP (Confirm) button. Never impact on the lens when adjusting zoom and focus lens. There's is a flicker on screen after finishing the adjustment. 2.5m +/-1Cm 3-24 Samsung Electronics...
Page 48
Store max. and min. value of in 167and 6) Press the START/STOP (Confirm) button. 168 respectively. 7) There's is a flicker on screen after finishing the 6) There's is a flicker on screen after finishing the adjustment. adjustment. 95IRE 95IRE Samsung Electronics 3-25...
Page 49
1) Camera mode & 3100˚ K gray scale chart 2) Connect a video output terminal to a vec- torscope and a TV. 3) Press the FF(Mode Up)/REW(Mode Down) button so that OSD shows "70 XX XX". 3-26 Samsung Electronics...
Page 50
1500-2000 Lux. 5) Press the PLAY (Data Up)/STOP (Data Down) so that the yellow level is 50IRE. 6) Press the START/STOP (Confirm) button to store data. 7) There's is a flicker on screen after finishing the adjustment. Samsung Electronics 3-27...
Page 51
1500-2000 Lux. 5) Press the PLAY (Data Up)/STOP (Data Down) so that the cyan vector is 284˚ . 6) Press the START/STOP (Confirm) button to store data. 7) There's is a flicker on screen after finishing the adjustment. 3-28 Samsung Electronics...
Page 52
Shift adjustment address to left. Shift adjustment address to right. REW (Mode Down) Up value. PLAY (Data Up) Down value. STOP (Data Down) Note: In service adjustment mode, button names are different from those in customer function control mode. Samsung Electronics 3-29...
Page 53
Connect an voltmeter to TP-VCOM. c) Adjust the EVR so that DC voltage is DC 1.1±0.05 V. Note: In LCD adjustment mode, when shorting "A" of PCB to GND and pressing the START/STOP button, EEPROM stores con- firmed adjustment value. 3-30 Samsung Electronics...
Page 54
Adjust the EVR so that Sync tip level is 4.2 Vp-p. 6) B-W/B a) TP-B & EVR b) Connect an oscilloscope probe to TP-B. c) Adjust the EVR so that Sync tip level is 4.4 Vp-p. Sync Tip Level Samsung Electronics 3-31...
Page 55
3-5-2. EVF adjustment 1) VIDEO GAIN a) Connect an oscilloscope probe to TP-V. b) Adjust the VRE02 so that A level is 2.5 Vp-p Remote Control Button Location 10 PIN CON. 2 PIN CON. Location of Test Point 3-32 Samsung Electronics...