VTech VM346 Quick Start Manual page 2

Overview - Parent unit
Antenna
Light indicators
Microphone
On/off
TALK
Zoom
Arrow keys
Basic operation - Parent unit
Adjust speaker volume Zoom
Press + / VOL / - to adjust your parent unit speaker Press to zoom in or out.
volume. It determines the volume of sound
transmitted from your baby unit.
1
)
Use the menu Turn off the parent unit
Press MENU/SELECT to enter the menu, choose Press and hold to power off your parent unit.
a menu item, or save a setting.
While in the menu:
• Press or to scroll up or down.
• Press to select an item.
• Press BACK to return to the main menu or
idle screen. 2s
Alert Tone
Low Battery Tone
No Link Alert
VIEW / LCD ON/OFF
PATROL
SPLIT
+ / VOL / -
MENU / SELECT
Stand
Talk to your baby unit Turn off the screen
Press and hold TALK and speak to your parent unit. Press and hold LCD ON/OFF to switch off
Your voice is transmitted to the baby unit. the screen. You can still hear sound from the
selected baby unit.
Long press
n a t h e o r M >
e t f e ( 3 e r e t m
Mount the baby monitor (optional)
If you drill the holes into a stud,
NOTES
• Check for reception strength and go to step 3.
camera angle before drilling the holes.
-OR-
Place the wall mount bracket on a If you drill the holes into an object
wall and then use a pencil to mark other than a stud, insert the wall
the top and the bottom holes as anchors into the holes. Tap gently
shown. Remove the wall mount on the ends with a hammer until
bracket and drill two holes in the the wall anchors are flush with
wall (7/32 inch drill bit). the wall.
Overview - Baby unit
Infrared LEDs
Light sensor
Camera
ON/OFF light
/ VOL /
Speaker
Play/Stop
Microphone
Power jack Skip
Basic operation - Baby unit
Adjust speaker volume Lullaby
/ VOL /
Press to adjust your baby unit speaker Press / to play lullaby on the baby unit.
volume. It determines the lullaby volume and
• Press to skip to the other lullabies.
talkback volume transmitted from your parent unit.
• Press / again to stop the lullaby.
2s
OR
Align the wall mount bracket and Place the baby unit on the wall Insert the screws into the
screws with the holes in the wall mount bracket. Tighten the screw holes and tighten the screws
as shown. Tighten the screw in the into the threaded socket at the until only 1/4 inch of the
middle hole first, so that the wall bottom to secure the baby unit. screws are exposed.
mount bracket position is fixed. You
can tighten the other screw in the
top hole.
Change different views
(require additional baby units - VM306/VM306-15/VM306-19)
You can view from different baby units if you have more than one baby units in your system
(VM306/VM306-15/VM306-19, purchased separately).
Speaker
Temperature
sensor
Press VIEW to switch between the images of the baby units.
ON/OFF slide
Press PATROL to alternately view the image from the baby units every 10 seconds.
Turn off the baby unit
Slide the ON/OFF switch to OFF to power off
your baby unit.
Press SPLIT to view the images from all baby units at once.
Place the baby unit on the wall mount The default angle of the wall mount bracket is 90 degrees. You
bracket. Tighten the screw into the threaded can maximize your baby unit's viewing angles by tilting the wall
socket at the bottom to secure the baby mount bracket.
unit. Align the holes on the wall mount
Hold the baby unit, and then rotate the knob in anticlockwise
bracket with the screws on the wall, and
direction. This will loosen the joint of the wall mount bracket.
slide the wall mount bracket down until it
Tilt your baby unit up or down to adjust to your preferred angle.
locks into place.
Then, rotate the knob in clockwise direction to tighten the joint
and secure the angle.
Press VIEW
10s
Specifications are subject to change without notice.
© 2016 VTech Communications, Inc. All rights reserved.
08/16. VM346_QSG_V3. Document order number: 96-011322-010-100