VTech DM111 User Manual

What's in the box
User's
Manual
POWER
1 set for DM111/DM111-2 1 set for DM111; 1 set for DM111/DM111-2
2 sets for DM111-2
Overview
Baby unit overview
1 – POWER light
2 – (On/off)
POWER
1
3 – Microphone
2
4 – Power jack
3
Parent unit overview
1 – Visual sound indicator
1
2 – POWER / LINK light
2
3 – LOW BATTERY light
3
4 –
(Volume down) 4
5 – (On/off) 5
6 – Speaker
6
7 – Belt clip
8 – (Volume up)
9 – Battery compartment cover
10 – Power jack
Connect
Connect the baby unit
NOTES
• Use only the parent unit power adapter and
NOTES
the baby unit power adapter supplied with this
product. • Make sure the POWER / LINK light is on after
the power plug is fully inserted into the power
• The parent unit power adapter and baby unit
jack of the parent unit.
power adapter are intended for a vertical
or floor mount position. The prongs are not • Make sure the baby unit is on. If the parent unit is
designed to hold the plug in place if it is plugged not linked to the baby
into a ceiling, under-the-table, or cabinet outlet. light on the parent unit will flash.
unit closer to the baby unit (but not less than
• Make sure the parent unit, the baby unit and the
1 meter / 3 feet).
power adapter cord are out of reach of children.
• Both the baby unit and the parent unit are on
once connected to the power supply.
Connect the baby unit
NOTE
• Make sure the POWER light is on after the
power plug is fully inserted into the power jack
of the baby unit.
4
POWER
Install batteries for temporary use
7
Install the batteries on the
You are recommended to use the power
adapter to power up the parent unit for
8 parent unit
normal use. If you want to move around
the house with the parent unit, or there is
9 NOTES
a power outage, install two AAA alkaline
• Use 2 x AAA batteries (not included). Alkaline
batteries for temporary use.
batteries are recommended. If you use other kind of
10
batteries, the performance of the baby monitor varies.
• The parent unit does not support battery recharging.
• Do not mix old and new batteries. Do not mix
POWER
alkaline, standard (Carbon-Zinc) or rechargeable
(Ni-Cad, Ni-Mh, etc) batteries.
• While you insert the batteries, make sure the
polarities are correct.
• When the batteries are installed, the parent unit
turns on.
1. Slide open the battery compartment
cover.
2. Flip the ribbon across the battery
compartment.
unit, the POWER / LINK
Move the parent
Replace the batteries when the LOW BATTERY light flashes on the parent unit, or you hear
a beep every 10 minutes.
Positioning the baby monitor
NOTE
• This baby monitor is intended as an aid. It is
not a substitute for proper adult supervision,
and should not be used as such.
Warning: Keep the baby unit out of the reach
of the baby. Never place or mount the baby unit
inside the baby's crib or playpen.
1. Place the baby unit at least
1 meter / 3 feet away from your baby.
NOTE
• If you experience audio feedback on either
the parent unit or baby unit, move the parent
unit further away until there is no more audio
feedback.
At least 1 meter
(3 feet)
POWER
Before use
3. Insert two AAA alkaline batteries into the
battery compartment on top of the ribbon.
Test the sound transmission of the baby
4. Slide the battery compartment cover until
monitor before initial use, and at regular
it clicks into place.
times thereafter.
Place the parent unit and the baby unit in
the same room to test the product.
To test the sound transmission:
• Speak towards the microphone of the
baby unit. You will hear the sound at
the parent unit, and see the visual
sound indicators light up.
Using your baby monitor
Power on or off the baby unit
To turn on the baby unit:
• Press and hold
turns on.
To turn off the baby unit:
• Press and hold
turns off.
Power on or off the parent unit
2. Place the parent unit at least
To turn on the parent unit:
1 meter / 3 feet away from the baby unit.
• Press and hold
light turns on.
To turn off the parent unit:
• Press and hold
POWER
At least 1 meter (3 feet)
light turns off.
Speaker volume of the parent unit
The speaker volume is preset to Level 3
on the parent unit. You can adjust to your
TIP
preferred sound level.
• You can increase the speaker volume of the
To adjust the speaker volume:
parent unit if you cannot hear the sounds
• Press to decrease the volume, and
transmitted from the baby unit.
increase the volume.
Operating range
NOTE
• If you continue to press
The operating range of the baby monitor is
reaches the minimum or maximum setting, the
up to 300 meters (1000 feet) outdoors or
parent unit will beep once.
50 meters (160 feet) indoors. The actual
To mute the speaker volume:
operating range may vary depending on
• Press repeatedly until the volume
the environmental conditions, and other
reaches the minimum.
interferences such as walls, doors, and
other obstructions. NOTES
• When the parent unit is in mute, the visual sound
indicator will still indicate the sound detected
from the baby unit.
• To unmute, press repeatedly until it reaches
your desired volume.
POWER
until the POWER light
POWER POWER
until the POWER light
until the POWER / LINK
unit the POWER / LINK
to
or when the volume