Table of Contents
Advertisement
Quick Links
User's Manual
User's Manual
FEBC-3150
IVC-3150
1, Aluminum chassis , Fan less design;
TM
2, Intel® Core
4th Gen I3/I5/I7 processor ;
3, 2xDDR3L 1600 SODIMM, max 16GB;
4, 3xMini PCIe support 3G/LTE/Wifi/BT/GPS/CAN;
5, DVI-I/HDMI/VGA display;
Ver, A1.0
6, 4xCOM/8bit DIO/4xUSB/Audio;
Date,7th.,Jul.,2015
7, 4× Intel I210-IT Power Over Ethernet；
8, 1xmSATA and 2x2.5inch HDD bay;
9, Smarter Vehicle Power Ignition for Variety Vehicle
1
Advertisement
Table of Contents
Summary of Contents for JHCTech FEBC-3150
- Page 1 User’s Manual User’s Manual FEBC-3150 IVC-3150 1, Aluminum chassis , Fan less design; 2, Intel® Core 4th Gen I3/I5/I7 processor ; 3, 2xDDR3L 1600 SODIMM, max 16GB; 4, 3xMini PCIe support 3G/LTE/Wifi/BT/GPS/CAN; 5, DVI-I/HDMI/VGA display; Ver, A1.0 6, 4xCOM/8bit DIO/4xUSB/Audio;...
- Page 2 User’s Manual Version Note Ver. Note Date Writer A1.0 first publish 20150707 Jiagang chen...
- Page 3 Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. All other product names or trademarks are properties of their respective owners. For more information on this and other JHC products, please visit our websites at: http://www.jhctech.com.cn...
- Page 4 User’s Manual Product Warranty (2 years) JHC warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by JHC, or which have been subject to misuse, abuse, accident or improper installation.
- Page 5 Technical Support and Assistance Step 1. Visit the JHC web site at www.jhctech.com.cn where you can find the latest information about the product.
-
Page 6: Safety Information
User’s Manual Safety Information Read the following precautions before setting up a JHCTECH Product. Electrical safety ● To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. ● When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. -
Page 7: Table Of Contents
User’s Manual Contents 1. Function Introduction ....................1 Model Specification ....................2 IVC-3150 Illustrantion(MB,System) ................4 2. Internal Connector Specification ................6 2.1 GPIO JST Connector ..................... 7 2.2 Power Input Connector....................8 3. External Connector Specification ................9 3.1 M12 Connecting to the Network .................. 10 3.2 DB29 Connector(DVI-I) .................... -
Page 8: Function Introduction
User’s Manual 1. Function Introduction... -
Page 9: Model Specification
User’s Manual 1.1 Model Specification System Intel Gen 4 Core i7‐4650U 1.7GHz up to 3.3GHz Intel Gen 4 Core i5‐4300U 1.9GHz up to 2.9GHz Intel Gen 4 Core i3‐4010U 1.7GHz Memory 2 x DDR3L 1600 MHz SO‐DIMM up to 16GB Chipset QM87 Intel I210‐AT Gb/s Ethernet Controllers Onboard... - Page 10 User’s Manual Audio 1 x Line‐out and 1 x Mic‐in (Line‐in Optional) SIM Card Socket 1 x SIM Card Socket Supported Onboard with eject Environment Operating Temp. ‐40º C ~ 70º C (Default CPU 17Watt) Storage Temp. ‐40 ~ 80º C Relative Humidity 0% RH–...
-
Page 11: Ivc-3150 Illustrantion(Mb,System)
User’s Manual 1.2 IVC-3150 Illustrantion(MB,System) Main Board Figture 1.1... - Page 12 User’s Manual Dimensions Figture 1.2...
-
Page 13: Internal Connector Specification
User’s Manual 2. Internal Connector Specification... -
Page 14: Gpio Jst Connector
User’s Manual 2.1 GPIO JST Connector Connector size 2 X 5 = 10 Pin Connector type JST-2.0mm-M-180 Signal Signal GPIO1 GPI0 GPI1 Connector Connector GPI2 GPI3 location GPO0 GPO1 definition GPO2 GPO3 +12V DIO Connection Dagram Connector map Table 2.1... -
Page 15: Power Input Connector
User’s Manual 2.2 Power Input Connector Connector size 1 X 4 = 4 Pin Connector WAFER 2.54mm-M-180 type PWRIN1 Signal Connector Connector pin location definition VIN (9-32V) IGNITION VBOX-3610’s Power Wiring Diagram Connector map Table 2.2... -
Page 16: External Connector Specification
User’s Manual 3. External Connector Specification... -
Page 17: M12 Connecting To The Network
User’s Manual 3.1 M12 Connecting to the Network A.M12 to RJ45 Cable Figure 3.1 B.M12 connector pin define Signal Signal TD1‐ TD1+ TD2+ TD3+ TD3‐ TD2‐ TD4+ TD4‐ Table 3.1 Figure 3.2 C.CAT5 connector pin define Figure 3.3 Signal Signal TD1+ TD1‐... -
Page 18: Db29 Connector(Dvi-I)
User’s Manual 3.2 DB29 Connector(DVI-I) Connector size 50 Pin Connector type DVI-I DVI-I1 Connector location Signal Signal DVI_ TX2_N DVI_TX2_P 5VSB +12V DVI_DDC_CLK DVI_DDC_DATA CRT_VSYNC DVI_ TX1_N DVI_TX1_P USB_7N Connector USB_7P DVI_HPD definition DVI_ TX0_N DVI_TX0_P CRT_DAC_SDA CRT_DAC_SCL DVI_CLK_P DVI_CLK_N CRT_RED CRT_GREEN CRT_BLUE... -
Page 19: Dp Connector
User’s Manual 3.3 DP Connector Connector 20 Pin size Connector type Display port Connector location Signal Signal DP2_LANE_0P DP2_ LANE_0N DP2_LANE_1P DP2_ LANE_1N Connector DP2_LANE_2P DP2_ LANE_2N DP2_LANE_3P definition DP2_ LANE_3N DP2_AUX_EN# DP2_AUXP_CLK DP2_AUXN_DATA DP2_HPD DP2_VCC3 Connector Table 3.4... -
Page 20: Db9 Connector(Com1)
User’s Manual 3.4 DB9 Connector(COM1) Connector size 9 Pin Connector type DSUB COM1 Connector location Signal Signal COM1_DCD / (RS- COM1_RXD Connector 485_TXD-/RXD-) (RS-485_TXD+/RXD+) COM1_TXD COM1_DTR definition COM1_DSR COM1_RTS COM1_CTS COM1_RI# Connector Table 3.5... -
Page 21: Db9 Connector(Com2)
User’s Manual 3.5 DB9 Connector(COM2) Connector 9 Pin size Connector type DSUB COM2 Connector location Signal Signal COM2_DCD / (RS- COM2_RXD Connector 485_TXD-/RXD-) (RS-485_TXD+/RXD+) COM2_TXD COM2_DTR definition COM2_DSR COM2_RTS COM2_CTS COM2_RI# Connector Table 3.6... -
Page 22: Phone Jack (Mic In)
User’s Manual 3.6 PHONE JACK (MIC IN) Connector 6 Pin size Connector type Phone Jack Connector location MIC1 Signal Signal Connector MIC_OUT-L MIC-JD MIC_ OUT-R definition Connector Table 3.7... -
Page 23: Phone Jack (Line Out)
User’s Manual 3.7 PHONE JACK (LINE OUT) Connector 6 Pin size Connector type Phone Jack Connector location LOUT1 Signal Signal Connector FRONT_OUT_L FRONT-JD FRONT_OUT_R definition Connector Table 3.8... -
Page 24: Atx 6Pin Connector (Power Out)
User’s Manual 3.8 ATX 6PIN Connector (POWER OUT) Connector 6 Pin size Connector type ATX 6PIN Connector location PWROUT1 Signal Signal Connector +12V +12V Relay -SO definition Relay-SI Connector Table 3.9... -
Page 25: Can Bus Pin Assignment
User’s Manual 3.9 CAN BUS Pin Assignment Figure 3.4 A. Connector pin definition Signal Signal CAN_GND CAN_L CAN_H CAN_GND Table 3.10... -
Page 26: System Installation
User’s Manual 4. System Installation... -
Page 27: System Introduction
User’s Manual 4.1 System Introduction Figure 4.1 Figure 4.2 4.2 Product accessories operation guidelines 4.2.1 Hard disk installation a.Fix the hard disk on the mounting bracket with 4 screws as shown in figure: Notice: Fix the hard disk like this. Figure 4.3 Figure 4.4... - Page 28 User’s Manual b. After fixing hard disk, load the hard drive along the guild slot as shown in figure. Notice: Slowly loading the hard drive along the guild slot. stuck,pls. dismount it to analyse . In order to ,pls. don’t avoid damage force to install Figure 4.5...
- Page 29 User’s Manual Notice: MSATA Position Figure 4.12 Figure 4.13 2）3G Module Installation a. Demount the connection line into 5 parts as shown in figure. Connetion wire Notice: The connection wire include 5 parts. Antenna Figure 4.14 Figure 4.15 b. Fix one end of the wire on the right hole of panel, and the other end of the wire on the 3G module as shown in figure.
- Page 30 User’s Manual Connection wire Notice: The connection wire include 5 Antenna parts. Figure 4.20 Figure 4.21 b. Fix one end of the wire on the right hole of panel, and the other end of the wire on the GPS module as shown in figure. Notice: Fix the other end of connection wire like...
- Page 31 User’s Manual Notice: Fix the other end of connection wire like this. Figure 4.28 Figure 4.29 c. Fix the antenna on the connection wire which was fixed in the side of panel Notice: Antenna fixed in connection line are shown at the exit Figure 4.30 4.2.4 SIM Card Install a.Press the key by screwdriver, and take the SIM card base plate out of the slot.
-
Page 32: System Resource
User’s Manual 5. System Resource... -
Page 33: Ignition Power Management Quick Guide
User’s Manual 5.1 Ignition Power Management Quick Guide Startup/shutdown conditions from the IGNITION signal: ◆ IGNITION startup signal must be valid during 3 sec. (anti‐noise protection). ◆ IGNITION shutdown – IGNITION signal must be inactive during 3 Sec, then PIC controller initiate Power Button signal (OS must be set to shut down from the Power... -
Page 34: Gpio & Delay Time Setting
User’s Manual Power Management Power‐off delay time is select-able by Software to disable and enable in 0‐255 minutes Ignition On/Off status detectable by SW If the ignition is off and the system is still on after 3 Sec, IVC‐3150 will shut If the ignition is turned on again and the power‐off delay is in progress, IVC‐3150 will cancel the delay function and will continue to operate normally. - Page 35 User’s Manual GPIO5 Output Enable Register – Index A0h Name R/W Default Description 0: GPIO57 is input GPIO57_OE 1: GPIO57 is output 0: GPIO56 is input GPIO56_OE 1: GPIO56 is output 0: GPIO55 is input GPIO55_OE 1: GPIO55 is output 0: GPIO54 is input GPIO54_OE 1: GPIO54 is utput...
- Page 36 User’s Manual GPIO5 Pin Status Register – Index A2h Name R/W Default Description GPIO57_ST GPIO57 pin status. GPIO56_ST GPIO56 pin status. GPIO55_ST GPIO55 pin status. GPIO54_ST GPIO54 pin status. GPIO53_ST GPIO53 pin status. GPIO52_ST GPIO52 pin status. GPIO51_ST GPIO51 pin status. GPIO50_ST GPIO50 pin status.
-
Page 37: Wdt Setting
User’s Manual I/O port: I/O port: 0xA35 (base address) for Control Register (Read 0xF2h bit 3) 0xA36 (base address) for Control Data Value Ignition Status 0 = Ignition off 1 = Ignition on Figure 5.2 Debug Command Line -O A35 F2 -I A36 // Check Bit 3 Status 5.2.2 WDT Setting I/O port:... - Page 38 User’s Manual Debug Command Line - O A16 05 - O A15 32 // 5 sec // 3A 5 minutes Watchdog Timer Function Watch dog timer is provided for system controlling. If time‐out can trigger one signal to high/low level/pulse, the signal is depend on register setting. The time unit has two ways from 1sec or 60sec.
- Page 39 User’s Manual Watchdog PME Control Register ‐ base address + 0Ah Name Default Description The PME Status ‐‐ WDT_PME This bit will set when WDT_PME_EN is set and the watchdog timer is 1 unit before time out (of time out) 0 : Disable Watchdog PME.
-
Page 40: Bios
User’s Manual 6. BIOS... -
Page 41: Super Io Configuration
User’s Manual 6.1 Super IO Configuration Figure 6.1 Select Serial Port Mode Figure 6.2 Select Power off Delay Time Figure 6.3...