Related Manuals for Omax MD8211E30
Summary of Contents for Omax MD8211E30
-
Page 1: User Manual
User Manual Digital Compound Binocular LED Microscope Model MD8211E30 MicroscopeNet.com ... -
Page 2: Table Of Contents
Table of Contents Caution...................... 1 ii. Care and Maintenance ................2 1. Components Illustration ................3 2. Installation ....................4 3. Operation ....................6 4. Specifications .................... 8 5. Troubleshooting Guide ................9... -
Page 3: Caution
www.microscopenet.com Caution 1. Open the carton carefully with a knife or paper cutter. Find the “UP” sign and place the Styrofoam container on the side that makes the arrow upward. If the “UP” sign is missing, please open the Styrofoam container gently to prevent any accessory items (i.e. -
Page 4: Care And Maintenance
www.microscopenet.com Care and Maintenance 1. Do not attempt to disassemble any component including eyepieces, objectives or focusing assembly. 2. Keep the instrument clean; remove dirt and debris regularly. Accumulated dirt on metal surfaces should be cleaned with a damp cloth. More persistent dirt should be removed using a mild soap solution. -
Page 5: Components Illustration
www.microscopenet.com 1. Components Illustration Eyepiece Light Collector Fine Focus Knob Diopter Ring Microscope Base X-Y Stage Moving Knobs Eyepiece Tube 10 USB Cable Power Switch 11 Head Lock Thumb Screw Brightness Intensity Dial Viewing Head w Built-in Camera Objective 12 Nosepiece Condenser Lock Thumb Screw Slide Holder 13 Microscope Body... -
Page 6: Installation
www.microscopenet.com 2. Installation 2.1 Installation of the digital binocular viewing head 1) Loosen the head lock thumb screw on the top of the microscope body and remove the plastic cover on the top. 2) Remove the cap on the dovetail of the digital binocular viewing head. 3) Seat the dovetail of the viewing head into the socket on the top of the microscope body and tighten the head lock thumb screw. - Page 7 www.microscopenet.com Color Filter Color Filter Holder Fig.2 2.6 Replacing the LED lamp 1) Turn off the power switch and disconnect the power cord. 2) Loosen the 7 screws on the bottom board. See Fig 3 (a) 3) Open the board and find the LED lamp. See Fig 3 (b) 4) Loosen the 2 screws and unplug the LED connector.
-
Page 8: Operation
www.microscopenet.com 3. Operation 3.1 Adjusting illumination 1) Plug the power cord into the power socket on the microscope and connect it to the power outlet. 2) Turn on the power switch. 3) Rotate the brightness intensity dial to increase or decrease the brightness of the illuminator. - Page 9 www.microscopenet.com 2) Then observe the specimen with your left eye only through the left eyepiece. If the specimen is not in focus, turn the diopter ring on the eyepiece tube until a sharp image is obtained. 3.6 Adjusting condenser 1) Turn the condenser focus knob to raise or lower the condenser. 2) The condenser is raised when using high magnification objectives and lowered when using low magnification objectives.
-
Page 10: Specifications
4. Specifications Model MD8211E30 Total Magnification 40X, 100X, 200X, 400X 30º inclined, 360º swiveling siedentopf binocular viewing head Viewing Head with built-in 3.0MP camera Hinge adjustment, 48mm - 75mm Interpupillary Distance Diopter Adjustment On left eyepiece tube Eyepieces 1 pair of WF10X/18... -
Page 11: Troubleshooting Guide
www.microscopenet.com 5. Troubleshooting Guide GENERAL PROBLEMS Problem Cause Solution No electrical power Check power cord connection Lamp does not light when LED or power unit dead Replace LED light switched on Fuse blown out Replace fuse Darkness at the periphery or Revolve the nosepiece to click-stop Revolving nosepiece not in click uneven...