Download Print this page

Philips 71361 Installation & Operation Manual

Portable led luminaire controllers, strand lighting, lighpack led 120v / 230v modules.
Hide thumbs

Advertisement

Advertisement

   Summary of Contents for Philips 71361

  • Page 2: Strand Lighting Offices

    Certain features of the equipment described in this document may form the subject of patents or patent applications. Document Number: 2-450226-010 Version as of: 09 May 2011 LightPack LED Module Installation & Operation Guide ©2011 Philips Group. All rights reserved.

  • Page 3: Important Safeguards

    LightPack LED Module Installation & Operation Guide Important Safeguards When using electrical equipment, basic safety precautions should always be followed including the following: a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. b. Do not use outdoors. c. Do not mount near gas or electric heaters. d.

  • Page 4: Table Of Contents

    LightPack LED Module Installation & Operation Guide TABLE OF CONTENTS Strand Lighting Offices................. Inside Front Cover Important Safeguards ......................1 TABLE OF CONTENTS ......................2 PREFACE ..........................3 About this Guide ....................... 3 ACCESSORIES ........................3 Clamps ..........................3 DMX512 Termination....................... 3 OVERVIEW ..........................

  • Page 5: Preface

    PREFACE About this Guide The document provides installation and operation instructions for the following products: • 71361 – LightPack LED 120V, Grounded Stage Pin Connector (GP) • 71362 – LightPack LED 120V, Twistlock Connector (GTL) • 71363 – LightPack LED 120V, Edison Connector (GR) •...

  • Page 6: Overview

    Installation & Operation Guide OVERVIEW LightPack LED controller delivers power and control to any Philips Selecon PL Wash luminaire or Philips Color Kinetics Color Blast wash lights. Smart addressing technology simplifies set up and allows users to quickly address any luminaire regardless of type. Users set an address, select an operating mode and press a button to set up any connected luminaire.

  • Page 7: Installation

    LightPack LED Module Installation & Operation Guide INSTALLATION The LightPack LED Module can be mounted in a variety of configurations. Depending on your requirements, choose one of the methods shown below. The LightPack LED Module can be mounted vertically (recommended) or horizontally as required, however, to allow for optimum convection cooling, the module cannot be mounted with the heatsink fins downward.

  • Page 8: Connecting Power

    LightPack LED Module Installation & Operation Guide CONNECTING POWER The LightPack LED Module is supplied with an AC input cable. Some versions are sold with AC input connectors installed. WARNING: DO NOT power module from a dimmed source. Connect to standard power or mechanical relay ONLY.

  • Page 9: Setting Modes And Dmx512 Address

    LightPack LED Module Installation & Operation Guide SETTING MODES AND DMX512 ADDRESS The operating modes and DMX512 address can be easily configured using the controls located inside the recess panel. There is one 4-position DIP switch (Configuration Switch) to configure the modes and three rotary DIP switches to configure the DMX512 address. For example (as shown in Figure 7), to set a DMX512 address of 471, set the 100’s dial to "4", the 10’s dial to "7", and the 1’s dial to "1".

  • Page 10: Operation

    LightPack LED Module Installation & Operation Guide OPERATION The LightPack LED Module will power up when the AC power is connected. (NOTE: the LightPack LED Module does not have a main on/off switch.) The LightPack LED Module provides two LED status indicators and a Focus/Bump buttons. LightPack LED Controller - Status LED Indicators The two LEDs associated with each channel report various operating conditions.

  • Page 11: Specifications

    Power Input: 100 ~ 240VAC, 50/60 Hz, 2 Amps Power Output: 24VDC, 55 Watts Per Connector Luminaire Types: Philips Selecon PL Washes or Philips Color Kinetics Color Blast Weight: 4.2 lbs (1.9 kg) DMX512 Connections: DMX512 In / Out (thru)

  • Page 12

    LightPack LED Module Installation & Operation Guide Part No. 2-450226-010...

This manual also for:

71362, 71363

Comments to this Manuals

Symbols: 0
Latest comments: