Table of Contents
Advertisement
16 - dSt Legal Time Selection.
(e.g. 0 Winter, 1 Summer)
17- Fac. (factory).
The purpose is to return the welding machine to the
original settings provided by the manufacturer. With the
function selected, the display AM shows noP = restores
the welding machine to the original settings disregarding
the stored programs, Prg = deletes all stored programs
and ALL = restores the welding machine to the original
settings.
To save the desired function press the button AV, the
abbreviation shown on the display AM will begin flashing;
after a few seconds, a sound will confirm that it has been
saved.
6 INSTALLATION
The
welding machine must be installed by skilled
personnel. All connections must be made in full compliance
with current safety laws (See CEI 26-23 - IEC/TS 62081).
6.1 PLACEMENT
The weight of the welding machine is approximately 80 Kg.
Position the unit in an area that ensures good stability, and
efficient ventilation so as to prevent metal dust (grinding)
from entering.
6.2 ASSEMBLY
Mount the plug on the power cord, being especially
careful to connect the yellow/green conductor to the earth
pole. Make sure that the supply voltage corresponds to
the rated voltage of the welding machine.
Size the protective fuses based on the data listed on the
technical specifications plate.
This
welding
machine
contemporarily mount 2 welding torches and 2 coils of
wire having a diameter of 300mm; this machine cannot
weld with the 2 torches at the same time, the torch
selection is made by means of selector switch D.
The gas cylinder must be equipped with a pressure
regulator and a gauge. If the cylinder is placed on the
cylinder shelf of the trolley, it must be fastened using
the strap provided. Only after positioning the cylinder,
connect the outgoing gas hose from the rear panel of the
machine to the pressure regulator.
2 gas hoses leave the rear panel, one is used in
combination with central adapter B and the other one
with central adapter B1. In order to select the right
combination read the plate at its side.
Adjust the gas flow to approximately 8/10 liters/minute
To make sure that the groove of the roller matches the
wire diameter used, open the mobile lateral side, remove
the cover CA, release the wire press roller by means of
the pressure adjusting knob BN, replace the roller and
remount the cover CA. (See fig.4).
16
has
been
designed
BN
Fig. 4
Mount the wire coil and slip the wire into the feeder and
welding torch sheath.
Block the wire press roller with the knob BN and adjust
the pressure.
Turn on the machine.
Adjust the gas by means of key AY and then feed the wire
by means of key AW.
7 WELDING
Welding Synergic Pulsed MiG LED AP on.
Select the PRG number based on the wire diameter to be
used, the type and quality of the material, and the type of
gas, using the instructions located inside the wire feeder
compartment.
Set the functions in the submenu according to the
instructions under paragraph «Service functions».
5.2.3The welding parameters are set by means of knobAI.
to
Synergic MiG Welding LED AQ on.
Select the PROG number based on the wire diameter
to be used, the type and quality of the material, and the
type of gas, using the instructions located inside the wire
feeder compartment.
Set the functions in the submenu according to the
instructions under paragraph «Service functions».
Adjust the wire speed and the welding voltage using the
knob AI.
Conventional MiG Welding LED AR on.
Select the PROG number based on the wire diameter
to be used, the type and quality of the material, and the
type of gas, using the instructions located inside the wire
feeder compartment.
Set the functions in the submenu according to the
instructions under paragraph «Service functions».
Adjust the wire speed and the welding voltage using the
knob AI. and AN respectively.
CA
Advertisement
Table of Contents
