Download Table of Contents Print this page

Specifications; Specific Safety Rules - Makita DA4030 Instructions Manual

Angle drill
Hide thumbs Also See for DA4030:

Advertisement

Table of Contents
ENGLISH
1
Tighten
2
Chuck key
3
Side grip
4
Spade grip
5
Wrench holder
6
Loosen
7
Hex wrench
8
mark
9
Motor housing
10 Lock button
11 Handle

SPECIFICATIONS

Model
Drilling capacities
Wood
Auger-bit .................................................................................38 mm
Self-feed bit.............................................................................65 mm
Hole saw .................................................................................
Steel ..........................................................................................13 mm
-1
No load speed (min
)...................................................................1,200
Overall length ...............................................................................417 mm
Overall length (with an extended spade grip) ...............................491 mm
Net weight.....................................................................................4.8 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1.
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
2.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the opeator.
3.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4.
Hold the tool firmly.
5.
Keep hands away from rotating parts.
Explanation of general view
12 Press
13 Switch trigger
14 Reversing switch lever
15 A side
16 Clockwise
17 B side
18 Counterclockwise
19 Speed change knob
20 Pointer
21 Lock button
22 Reaction
6.
7.
8.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
GEB001-2
Installing or removing drill bit (Fig. 1)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each
of the three holes and tighten clockwise. Be sure to
tighten all three chuck holes evenly. To remove the bit,
turn the chuck key counterclockwise in just one hole,
then loosen the chuck by hand. After using the chuck key,
be sure to return it to the original position.
23 Forward
24 Drilling in forward bit turns
clockwise
25 Reverse
26 Reversing bit turns
counterclockwise
27 Limit mark
28 Screwdriver
29 Brush holder cap
DA4030
High: 65 mm
Low: 118 mm
High: 1,200
Low: 300
Do not leave the tool running. Operate the tool
only when hand-held.
Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
DA4031
38 mm
152 mm
13 mm
462 mm
536 mm
5.6 kg
5

Advertisement

Table of Contents
loading

This manual is also suitable for:

Da4031

Table of Contents