Download Table of Contents Print this page

Makita DA4000LR Instruction Manual

13 mm (1/2”) angle drill
Hide thumbs Also See for DA4000LR:

Advertisement

Angle Drill
13 mm (1/2")
MODEL DA4000LR
I N S T R U C T I O N
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
w w w . m a k i t a t o o l s . c o m
DOUBLE
INSULATION
M A N U A L
003009

Advertisement

Table of Contents
loading

Summary of Contents for Makita DA4000LR

  • Page 1 Angle Drill 13 mm (1/2”) MODEL DA4000LR I N S T R U C T I O N WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. w w w . m a k i t a t o o l s . c o m...
  • Page 2: Specifications

    If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified elec- trician to install a polarized outlet. Do not DA4000LR 13 mm (1/2”) 38 mm (1-1/2”) 0 - 900/min.
  • Page 3 change the plug in any way. Double insula- tion eliminates the need for the three wire grounded power cord and grounded power supply system. 5. Avoid body contact with grounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.
  • Page 4 model. Accessories that may be suitable for one tool, may become hazardous when used on another tool. SERVICE 23. Tool service must be performed only by qualified repair personnel. Service or main- USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw.
  • Page 5: Specific Safety Rules

    SPECIFIC SAFETY RULES DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to drill safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces...
  • Page 6 SYMBOLS The followings show the symbols used for tool. V ... volts A ... amperes Hz ... hertz ... alternating current ...no load speed ˚ ...Class II Construction .../min...revolutions or reciprocation per minute USD201-2...
  • Page 7: Functional Description

    FUNCTIONAL DESCRIPTION 003022 1. Switch trigger 003029 1. Reversing switch lever ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF”...
  • Page 8 “HIGH”. The higher speed is better suited for drilling smaller diameter holes. For lower speed operation, attach the drill chuck to the end marked “LOW”. The lower speed is best utilized for drilling larger diameter holes.
  • Page 9 CAUTION: • The drill chuck and the bolt are assembled each other. Turn the bolt counterclockwise about 10 times so that they can be removed together. Loosen the bolts of the joint by the hex wrench and remove the angle housing, the joint and the socket.
  • Page 10 2. Spindle 003055 1. Chuck key Slide the drill chuck to the spindle so that the two faces are fitted perfectly. Holding the drill chuck with the chuck key, tighten the bolt (for installing the drill chuck) clockwise with the hex wrench firmly.
  • Page 11: Operation

    OPERATION Holding tool When drilling a large hole with a hole saw, etc., the side grip (auxiliary handle) should be used as a brace to maintain safe control of the tool. Drilling operation Drilling in wood When drilling in wood, the best results are obtained with wood drills equipped with a guide screw.
  • Page 12: Maintenance

    CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold...
  • Page 14 Paste 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog 4. Most favored points are: Design Features Size Price Makita Brand MODEL NO. YEAR SERIAL NO. PHONE 20-29 30-39 40-49 Paste Paste Radio Exhibition...
  • Page 15: Factory Service Centers

    Date Purchased When you need service: Send complete tool (prepaid) to one Dealer’s Name & Address of the Makita Factory Service Centers listed, or to an Authorized Makita Service Center. Be sure to attach a letter to the outside of Model No.
  • Page 16: Warranty Policy

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.

Table of Contents