Advertisement
Troubleshooting
The table below lists the several steps involved when adding or removing the detector from
the Z-wave network.
Action/Status
Description
The Z-Wave Controller does not allocate a
No node ID
node ID to the unit.
The power is applied for the first time and no
Auto Inclusion
node ID has been stored in the module, or
after executing reset.
1. Put the Z-Wave Controller into
inclusion mode.
Manual Inclusion
2. Press the tamper switch 3 times within 1.5
seconds to put the unit into inclusion
mode.
1. Put the Z-Wave Controller into exclusion
mode.
2. Press the tamper switch 3 times within 1.5
seconds to put the unit into exclusion
mode.
Exclusion
2. Within 1 second of step 1, press the
tamper switch again and hold until LED is
off (about 5 seconds).
3. Node ID is excluded. The device reverts
to factory default state and will be in
auto-inclusion mode for 4 minutes.
Failed or successful results in including/excluding the ID can be viewed on the Z-Wave
Controller.
Table below lists typical problems encountered:
Symptom
Possible Cause
Cannot carry out
1.
Run out of battery power
inclusion and
2.
Check if reverse battery
association
polarity
3.
Check if the detector is
out of order
Cannot control the
1.
Run out of battery power
connected modules
2. Check if the detector is
out of order
The detector not
1.
Run out of battery
working
power
2.
Check if the mounting
location is proper
3.
Check if the detector is
mounted above a
radiator or heater
4.
Check if the detector is
out of order
LED indication
2-second on, 2-second
off
For 2 minutes
Recommendation
1.
Replace a new battery
2.
Refit the battery with
correct polarity
3.
Ensure the detector is
working properly
1.
Replace a new battery
2.
Ensure the detector is
working properly
1.
Replace a new battery
2.
Reposition its mounting
location
3.
Remove the source of
interference or reposition
its mounting location
4.
Ensure the detector is
working properly
Specifications
Battery
1.5V AA size x 3
Battery Life
1 year*
Range
Up to 100 meters line of sight
Warm Up Time
About 1 minute
PIR Detection Coverage
Up to 10m x 100° (at 2m mounting height & below 20°C)
Frequency Range
908.42 MHz (US) / 868.42 MHz (EU)
Specifications are subject to change without notice
*measured at 10 triggers per day
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
WARNING:
Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities.
Contact your local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can
leak into the groundwater and get into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back
your old appliance for disposal at least for free of charge.
50 Sect. 1 Zhonghua Rd Tucheng
www.everspring.com
NewTaipeiCity 236 Taiwan
This
A501112630R
Advertisement
