Table of Contents
Advertisement
INSTALLATION AND OPERATION INSTRUCTIONS
4400QC SERIES POWER PAKS
IMPORTANT INFORMATION
To register your product, visit our web site at www.
perlick.com. Click on Commercial, then Service.
You will see the link to Warranty Registration Form.
You must complete and submit this form or the
installation date will revert back to the ship date.
Permanently mount the enclosed Warning/Safety
Instruction label in a visible location near the CO2
regulator.
This manual has been prepared to assist you in the
installation of your 4400QC Series Power Pak and to
acquaint you with its operation and maintenance.
We dedicate considerable time to ensure that our
products provide the highest level of customer
satisfaction. If service is required, your dealer can
provide you with a list of qualified service agents. For
your own protection, never return merchandise for
credit without our approval.
We thank you for selecting a Quck Chill product and
assure you of our continuing interest in your
satisfaction.
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414.353.7060 • Fax 414.353.7069
Toll Free 800.558.5592 • E-Mail perlick@perlick.com • www.perlick.com
Table of Contents
Sizes & Specifications ............................................ 2-3
General Information .......................................... 3
Installation ..................................................... 3-4
Connecting Power Pak to Trunk Housing ........... 4-5
Power Pak Start-Up ................................................ 5-6
LEDS ...................................................................... 6-7
Preventative Maintenance ...................................... 6-7
Replacement Parts .................................................... 7
Wiring Diagrams ........................................................ 8
MODELS
4400QC Series
4404QC
4410QC
4414QC
4420QC
C
US
Form No. Z0507QC
Rev. 03.22.2018
Advertisement
Table of Contents
Related Manuals for Perlick 4400QC Series
Summary of Contents for Perlick 4400QC Series
-
Page 1: Table Of Contents
Replacement Parts ............ 7 This manual has been prepared to assist you in the Wiring Diagrams ............8 installation of your 4400QC Series Power Pak and to acquaint you with its operation and maintenance. We dedicate considerable time to ensure that our products provide the highest level of customer satisfaction. -
Page 2: Sizes & Specifications
C22296A-20--Cord Kit for 4404 & 4410 single pump units 61791+1--Triple Tier Rack (field installed) 61792+1--Quad Tier Rack **Requires four wires (2 hot, 1 neutral, and 1 ground) Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice... -
Page 3: General Information
INSTALLING THE POWER PAK Prior to installing a 4400QC Series Power Pak, it is imperative that the method of connecting it to the electrical service has been determined. Ensure that the electrical service to power the Power Pak will handle the load requirements. -
Page 4: Installation
■ Take oetiker clamps, and install over coolant tubing ends. ■ Push coolant lines, one each over pump outlet Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice... -
Page 5: Power Pak Start-Up
Power Pak to cut-out on the temperature control. Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice Form No. Z0507QC Rev. 03.22.2018... -
Page 6: Leds
The controller has been factory programmed to continue operation with the compressor cycling on and off in 5 minute intervals. Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice... -
Page 7: Replacement Parts
Compression Fitting 1008057 V-Clamp 63291-2 Switch 63303 Coupling 63291-3 Drier 63297 Thermostat 1007439 Coolant Solution 63299-1 Probe 1006596P Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice Form No. Z0507QC Rev. 03.22.2018... -
Page 8: Wiring Diagrams
WIRING DIAGRAMS - 4400QC SERIES POWER PAKS Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice Form No. Z0507QC Rev. 12.14.2016...