• Do not drop, sit on, or allow the HC1 to be immersed in water or other liquids. • Do not leave outdoors or in vehicle for extended period of time.
This Quick Reference Guide explains how to install and charge the battery, proper install the HC1 on the user’s head and install accessories. Unpacking Carefully remove all protective material from around the HC1 and save the shipping container for later storage and shipping. Verify that you received all equipment listed below: •...
HC1 Headset Computer Features Firm Goods Assembly Headstrap Computer/Optical Pod Audio Port Assembly Computer Charging Neck Pad Connector/Firm Good Mount Accessory Port Programmable Speaker Function Button Pivot Arm Module Review Copy Optical Pod Optical Focus Optical Focus Optical Focus Optical Boom...
Adjust head strap Adjust optic pod. Installing the Battery To install the battery: NOTE These procedure show the HC1 with a 1950 mAh battery. Some HC1 configurations come with a 4800 mAh battery. Review R R R R R R R...
Using a screwdriver or coin, turn the locking screw clockwise 1/4 turn to the lock position. Charging the HC1 CAUTION Do not place on head while charging. Before using the HC1, charge the battery. If a fully charged battery is installed, skip this procedure. Review Copy...
Charge until the LED turns green. LED State Description Slow Flashing Amber HC1 is charging. Solid Green HC1 is fully charged. Fast Flashing Amber Charging Error. Press the Charging Adapter release latches and remove the Charging Adapter from the Computer/Optical Pod Assembly.
Re-positioning the Computer/Optical Pod Assembly From the factory, the HC1 is configured for left eye dominant. To switch the optical pod position: If not already removed, press the release latches to remove the Firm Goods Assembly from the Computer/Optical Pod Assembly.
Quick Reference Guide Reconnect the Firm Goods Assembly to the Computer/Optical Pod Assembly. Review R R R R ev v Rev v e e e e e e e Copy Re-positioning Speaker Module NOTE By default, the Speaker Module is installed on the right side. The user can switch the Speaker Module to the left side if desired.
Press the Speaker Module in until it snaps into place. Placing the HC1 on Head The HC1 is worn on the head so that the main body of the device fits behind the base of the Review Copy head with the strap sitting on top of the head.
Re e v evie evie ev v v ev v v v v v v v ie i i i w w w w w Copy Make sure the HC1 is balanced on head like you would a pair of eyeglasses.
Revie Copy The HC1 pivot points allow the user to properly position the Optical Pod and to move the Optical Pod when the user does not need to use it. The Coarse Pivot Point allows for moving the Optical Pod large distances. The Fine Pivot point allow for fine tuning of the position.
Quick Reference Guide Pod Pivot Point Coarse Pivot Point Fine Pivot Point Optical Boom Move the Optical Boom in or out to position under eye. Revie Revi R vie e e e e e e e e e e Copy Position the optical boom so that the Optical Pod is positioned approximately two fingers distance from the eye wear.
Hold the HC1 with one hand and rotate the arm at the Coarse Pivot Point. Hold the HC1 with one hand and rotate the arm at the Fine Pivot Point. Repeat adjustments until the Optical Pod is two finger lengths away from safety glasses and out of the user’s line of sight.
If the Computer/Optical Pod Assembly was rotated, the display appears upside down. Say “My Computer” > “My Controls” > “Screen Rotation” > “Rotate Screen.” Refer to the HC1 User Guide for information on how to flip the display image.
HC1 Headset Computer Basic Usage Head Tracker Navigation The HC1 contains 9-axis head tracking sensors that allow the user to move the objects on the display by moving their head up and down and left and right. R R R e...
Latch Latch Voice Control Review Copy The HC1 is equipped with voice recognition software that allows the user to control is equipped with voice recognition softwa is equipped with voice that allows the user to control hat allo software functionality by speaking specific on-screen commands. Refer to the HC1 User...
HC1 Headset Computer Positioning Optical Pod When not in Use The user can move the Optical Pod away from the face when it is not being used for long periods of time. Grasps the boom and rotate up and away from the face.
To install a microSD card: croSD car Press the Power button for one second to place the HC1 into suspend mode. The LED flashes red momentarily and then turns off. Using a #1 Phillips screwdriver, remove the screw securing the card cover.
Close the card cover. Secure the card cover using a #1 Phillips screwdriver. Press the Power button to wake up the HC1. Ear Buds Ear Buds provide an optional solution for the user that requires ear protection to hear audio from the HC1.
HC1 tting the HC To reset the HC1 press the Power button for at least eight seconds. The display turns off the HC1 press the Power button for at lea the HC1 press the Power button for at le eight seconds.
HC1 Headset Computer Bluetooth® Wireless Technology This is an approved Bluetooth® product. For more information or to view End Product Listing, please visit https://www.bluetooth.org/tpg/listings.cfm Wireless Device Country Approvals Regulatory markings, subject to certification, are applied to the device signifying the...
Quick Reference Guide • Provide adequate clearance • Provide a suitable working environment • Improve work procedures. Note: The following section is only applicable for mobile computers. Vehicle Installation RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems).
For information on “International” human exposure to electromagnetic fields refer to the Motorola/Symbol Declaration of Conformity (DoC) at http://www.motorolasolutions.com/doc Europe Head Worn Devices This device was tested for Head Mounted operation. Use only Motorola tested and approved accessories to ensure EU Compliance.
US and Canada Head Worn Devices This device was tested for typical body-worn operation. Use only Motorola tested and approved accessories to ensure FCC / IC Compliance. The use of third-party accessories may not comply with FCC / IC RF exposure compliance requirements, and should be avoided.
Particular care should be taken where the device is charged in a non commercial environment. • Follow battery usage, storage, and charging guidelines found in the HC1 User Guide. • Improper battery use may result in a fire, explosion, or other hazard.
Quick Reference Guide Radio Frequency Interference Requirements- FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
• Italy requires a user license for outside usage. Statement of Compliance Motorola/Symbol hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from http://www.motorolasolutions.com/doc.
: http://www.motorolasolutions.com/recycling/weee. Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Motorola al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: http://www.motorolasolutions.com/recycling/weee.
„Motorola“. Daugiau informacijos, kaip gr žinti gamin , rasite: http://www.motorolasolutions.com/recycling/weee. Latviešu: ES klientiem: visi produkti p c to kalpošanas m ža beig m ir j nog d atpaka Motorola otrreiz jai p rstr dei. Lai ieg tu inform ciju par produktu nog d šanu Motorola, Review Copy l dzu, skatiet: http://www.motorolasolutions.com/recycling/weee.
• Title of the software download you are requesting. If it is determined by Motorola that your device is entitled to the latest software release, you will receive an e-mail containing a link directing you to a Motorola Web site to download the appropriate software.