1. Manuals
  2. Brands
  3. IEI Technology Manuals
  4. Control Unit
  5. ICE-9652
  6. User manual

IEI Technology ICE-9652 User Manual

Com express basic type module intel core 2 duo/celeron m processor with vga/lvds, gbe, sata, usb and audio
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ICE-9652/9602 COM Express Basic Type 2 Module
IEI Technology Corp.
MODEL:
MODEL:
ICE-9652/9602
COM Express Basic Type 2 Module
Intel® Core™2 Duo/Celeron® M Processor with
VGA/LVDS, GbE, SATA, USB and Audio
Rev. 1.00 – 5 March, 2009
ICE-9652/9602
User Manual
Page i

Advertisement

Table of Contents
loading

Related Manuals for IEI Technology ICE-9652

Summary of Contents for IEI Technology ICE-9652

  • Page 1 ICE-9652/9602 COM Express Basic Type 2 Module ICE-9652/9602 IEI Technology Corp. MODEL: MODEL: ICE-9652/9602 COM Express Basic Type 2 Module Intel® Core™2 Duo/Celeron® M Processor with VGA/LVDS, GbE, SATA, USB and Audio User Manual Page i Rev. 1.00 – 5 March, 2009...
  • Page 2 ICE-9652/9602 COM Express Basic Type 2 Module Revision Date Version Changes 5 March, 2009 1.00 Initial release Page ii...
  • Page 3 ICE-9652/9602 COM Express Basic Type 2 Module Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

  • Page 4: Table Of Contents

    ICE-9652/9602 COM Express Basic Type 2 Module Table of Contents 1 INTRODUCTION......................1 1.1 I ......................2 NTRODUCTION 1.2 A ......................2 PPLICATIONS 1.3 B ........................3 ENEFITS 1.4 F ........................3 EATURES 1.5 O ....................4 VERVIEW ICTURE 1.6 D .......................
  • Page 5 ICE-9652/9602 COM Express Basic Type 2 Module 4.4.1 BIOS Selection ....................31 4.4.2 LVDS Panel Resolution..................32 4.4.3 PEG and SDVO Configuration ................ 33 4.5 M ICE-9652/9602 ................34 OUNTING THE 5 BIOS SETUP ........................ 37 5.1 I ......................38 NTRODUCTION 5.1.1 Starting Setup....................
  • Page 6 ICE-9652/9602 COM Express Basic Type 2 Module 6 SOFTWARE INSTALLATION .................. 79 6.1 A ................80 VAILABLE OFTWARE RIVERS 6.2 S ................80 TARTING THE RIVER ROGRAM 6.3 C ................82 HIPSET RIVER NSTALLATION 6.4 VGA D ..................85 RIVER NSTALLATION 6.5 LAN D...
  • Page 7 ICE-9652/9602 COM Express Basic Type 2 Module List of Figures Figure 1–1: ICE-9652/9602 with Heatspreader and Heatsink .............2 Figure 1-2: ICE-9652/9602 Overview (Front Side)................4 Figure 1-3: ICE-9652/9602 Overview (Reverse Side)..............5 Figure 1-4: Main Dimensions (mm)....................6 Figure 1-5: Side Dimensions (mm) ....................7 Figure 1-6: Data Flow Block Diagram ...................8...
  • Page 8 ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-14: GMA Driver Installing Notice .................89 Figure 6-15: GMA Driver Installation Complete.................89 Figure 6-16: Access Windows Control Panel ................90 Figure 6-17: Double Click the System Icon................90 Figure 6-18: Click the Device Manager Button ................91 Figure 6-19: Device Manager List ....................91...
  • Page 9 ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-49: Select Driver Location ..................113 Figure 6-50: Install From Disk ....................113 Figure 6-51: Locate File ......................114 Figure 6-52: Install From Disk ....................114 Figure 6-53: iSMM Directory ..................... 115 Figure 6-54: iSMM Installation File...................
  • Page 10 ICE-9652/9602 COM Express Basic Type 2 Module List of Tables Table 1-1: Technical Specifications....................10 Table 2-1: Package List Contents ....................13 Table 3-1: ICE-9652/9602 Interface Connectors ................16 Table 3-2: COM Express Connector AB Pin Definitions............20 Table 3-3: COM Express Connector CD Pin Definitions............25 Table 3-4: SPI Flash Connector....................26...
  • Page 11 ICE-9652/9602 COM Express Basic Type 2 Module BIOS Menus BIOS Menu 1: Main ........................40 BIOS Menu 2: Advanced ......................42 BIOS Menu 3: CPU Configuration ....................42 BIOS Menu 4: IDE Configuration....................43 BIOS Menu 5: IDE Master and IDE Slave Configuration ............45 BIOS Menu 6: IDE Master and IDE Slave Configuration ............49...

  • Page 13: Introduction

    ICE-9652/9602 COM Express Basic Type 2 Module Chapter Introduction Page 1...

  • Page 14: Introduction

    COM Express carrier board to be designed, while leaving the choice of processor till the later stages of design. The ICE-9652/9602 provides a low power option with the full range of modern I/O options. The ICE-9652/9602 embedded module is designed for flexible integration by system developers into customized platform devices.

  • Page 15: Benefits

    ICE-9652/9602 COM Express Basic Type 2 Module 1.3 Benefits Some of the ICE-9652/9602 embedded platform benefits include: Low power, high performance Easy integration into customized baseboards Easy upgrading Easy maintenance Easy design compatibility Low cost product development 1.4 Features Some of the ICE-9652/9602 features are listed below:...

  • Page 16: Overview Picture

    ICE-9652/9602 COM Express Basic Type 2 Module 1.5 Overview Picture An overview of the ICE-9652/9602 embedded module can be seen in Figure 1-2 and Figure 1-3. Figure 1-2: ICE-9652/9602 Overview (Front Side) Page 4...

  • Page 17: Figure 1-3: Ice-9652/9602 Overview (Reverse Side)

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 1-3: ICE-9652/9602 Overview (Reverse Side) Page 5...

  • Page 18: Dimensions

    ICE-9652/9602 COM Express Basic Type 2 Module 1.6 Dimensions The main dimensions of the ICE-9652/9602 are shown in the diagram below. Length: 125 mm Width: 95 mm Figure 1-4: Main Dimensions (mm) Page 6...

  • Page 19: Side Dimensions

    ICE-9652/9602 COM Express Basic Type 2 Module 1.6.1 Side Dimensions The figure below shows the dimensions as viewed from the side. Figure 1-5: Side Dimensions (mm) Page 7...

  • Page 20: Data Flow

    ICE-9652/9602 COM Express Basic Type 2 Module 1.7 Data Flow Figure 1-6 shows the data flow between the two on-board chipsets and other components installed on the motherboard and described in the following sections of this chapter. Figure 1-6: Data Flow Block Diagram...

  • Page 21: Technical Specifications

    ICE-9652/9602 COM Express Basic Type 2 Module 1.8 Technical Specifications ICE-9652/9602 technical specifications are listed in Table 1-1. Detailed descriptions of each specification can be found in the detailed specifications chapter. Specification ICE-9652/9602 COM Express Type II Form Factor Socket P...

  • Page 22: Table 1-1: Technical Specifications

    ICE-9652/9602 COM Express Basic Type 2 Module Three SATA II (through baseboard) SATA One IDE channel to baseboard Environmental and Power Specifications Power Support AT/ATX power supported Power Consumption 12 V @ 3.039 A 2.2 GHz Intel® Core™2 Duo T7500 processor with 1.0 GB...

  • Page 23: Unpacking

    ICE-9652/9602 COM Express Basic Type 2 Module Chapter Unpacking Page 11...

  • Page 24: Anti-Static Precautions

    Only handle the edges of the PCB:- Don't touch the surface of the motherboard. Hold the motherboard by the edges when handling. 2.2 Unpacking Precautions When the ICE-9652/9602 is unpacked, please do the following: Follow the antistatic guidelines above. Make sure the packing box is facing upwards when opening.

  • Page 25: Packing List

    If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the ICE-9652/9602 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw.

  • Page 26: Connectors

    ICE-9652/9602 COM Express Basic Type 2 Module Chapter Connectors Page 14...

  • Page 27: Peripheral Interface Connectors

    ICE-9652/9602 COM Express Basic Type 2 Module 3.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 ICE-9652/9602 Layout The figures below show all the connectors and jumpers. Figure 3-1: Connector and Jumper Locations (Front Side) Figure 3-2: Connector and Jumper Locations...

  • Page 28: Peripheral Interface Connectors

    DIMM2 SPI connector 6-pin wafer SPI1 Table 3-1: ICE-9652/9602 Interface Connectors 3.2 Internal Peripheral Connectors The section describes all of the connectors on the ICE-9652/9602. 3.2.1 COM Express Connector AB CN Label: CN Type: 220-pin COM Express connector CN Location:...

  • Page 29: Figure 3-3: Com Express Connector Ab Location

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 3-3: COM Express Connector AB Location Pin No. Description Pin No. Description GBE0_MDI3- GBE0_ACT# GBE0_MDI3+ LPC_FRAME# GBE0_LINK100# LPC_AD0 GBE0_LINK1000# LPC_AD1 GBE0_MDI2- LPC_AD2 GBE0_MDI2+ LPC_AD3 GBE0_LINK# LPC_DRQ0# GBE0_MDI1- LPC_DRQ1# GBE0_MDI1+ LPC_CLK GBE0_MDI0- PWRBTN#...
  • Page 30 ICE-9652/9602 COM Express Basic Type 2 Module Pin No. Description Pin No. Description SUS_S4# SUS_STAT# SATA0_RX+ SATA1_RX+ SATA0_RX- SATA1_RX- SATA2_TX+ SATA2_TX- SUS_S5# PWR_OK SATA2_RX+ SATA2_RX- BATLOW# ATA_ACT# AC_SDIN2 AC_SYNC AC_SDIN1 AC_RST# AC_SDIN0 AC_BITCLK SPKR AC_SDOUT I2C_CK BIOS_DISABLE# I2C_DAT THRMTRIP# THRM#...
  • Page 31 ICE-9652/9602 COM Express Basic Type 2 Module Pin No. Description Pin No. Description LPC_SERIRQ CB_RESET# GPI0 GPO1 PCIE_TX4+ PCIE_RX4+ PCIE_TX4- PCIE_RX4- GPO2 PCIE_TX3+ PCIE_RX3+ PCIE_TX3- PCIE_RX3- PCIE_TX2+ PCIE_RX2+ PCIE_TX2- PCIE_RX2- GPI1 GPO3 PCIE_TX1+ PCIE_RX1+ PCIE_TX1- PCIE_RX1- WAKE0# GPI2 WAKE1# PCIE_TX0+...

  • Page 32: Table 3-2: Com Express Connector Ab Pin Definitions

    ICE-9652/9602 COM Express Basic Type 2 Module Pin No. Description Pin No. Description LVDS_A_CK- LVDS_B_CK- LVDS_I2C_CK LVDS_BKLT_CTRL LVDS_I2C_DAT 5VSB GPI3 5VSB KBD_RST# 5VSB KBD_A20GATE 5VSB PCIE0_CK_REF+ PCIE0_CK_REF- VGA_RED RSVD VGA_GRN RSVD VGA_BLU GPO0 VGA_HSYNC RSVD VGA_VSYNC RSVD VGA_I2C_CK VGA_I2C_DAT +V12...

  • Page 33: Com Express Connector Cd

    ICE-9652/9602 COM Express Basic Type 2 Module 3.2.2 COM Express Connector CD CN Label: 220-pin COM Express connector CN Type: CN Location: See Figure 3-4 CN Pinouts: See Table 3-3 The standard COM Express connector locations and pinouts are shown below.
  • Page 34 ICE-9652/9602 COM Express Basic Type 2 Module Pin No. Description Pin No. Description IDE_D13 IDE_IOW# IDE_D1 IDE_ACK# IDE_D14 IDE_IRQ IDE_IORDY IDE_A0 IDE_IOR# IDE_A1 PCI_PME# IDE_A2 PCI_GNT2# IDE_CS1# PCI_REQ2# IDE_CS3# PCI_GNT1# IDE_RESET# PCI_REQ1# PCI_GNT3# PCI_GNT0# PCI_REQ3# PCI_REQ0# PCI_AD1 PCI_RESET# PCI_AD3 PCI_AD0...
  • Page 35 ICE-9652/9602 COM Express Basic Type 2 Module Pin No. Description Pin No. Description PCI_AD21 PCI_AD24 PCI_AD23 PCI_AD26 PCI_C/BE3# PCI_AD28 PCI_AD25 PCI_AD30 PCI_AD27 PCI_IRQC# PCI_AD29 PCI_IRQD# PCI_AD31 PCI_CLKRUN# PCI_IRQA# PCI_IRQB# PCI_CLK PEG_RX0+ PEG_TX0+ PEG_RX0- PEG_TX0- PEG_RX1+ PEG_TX1+ PEG_RX1- PEG_TX1- PEG_RX2+ PEG_TX2+...
  • Page 36 ICE-9652/9602 COM Express Basic Type 2 Module Pin No. Description Pin No. Description SDVO_DATA SVDO_CLK FAN_TACHOIN IDE_CBLID# C100 D100 C101 D101 C102 D102 C103 D103 C104 +V12 D104 +V12 Page 24...

  • Page 37: So-Dimm Connector

    ICE-9652/9602 COM Express Basic Type 2 Module Pin No. Description Pin No. Description C105 +V12 D105 +V12 C106 +V12 D106 +V12 C107 +V12 D107 +V12 C108 +V12 D108 +V12 C109 +V12 D109 +V12 C110 D110 Table 3-3: COM Express Connector CD Pin Definitions 3.2.3 SO-DIMM Connector...

  • Page 38: Spi Flash Connector

    ICE-9652/9602 COM Express Basic Type 2 Module 3.2.4 SPI Flash Connector CN Label: JSPI1 6-pin wafer (1x6) CN Type: CN Location: See Figure 3-6 CN Pinouts: See Table 3-4 The 6-pin SPI Flash connector is used to flash the BIOS.

  • Page 39: Installation

    ICE-9652/9602 COM Express Basic Type 2 Module Chapter Installation Page 27...

  • Page 40: Anti-Static Precautions

    Electrostatic discharge (ESD) can cause serious damage to electronic components, including the ICE-9652/9602. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the ICE-9652/9602, or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
  • Page 41 This helps to prevent potential ESD damage. Turn all power to the ICE-9652/9602 off: When working with the ICE-9652/9602, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system.

  • Page 42: So-Dimm Installation

    Figure 4-1. Figure 4-1: SO-DIMM Installation Step 1: Locate the SO-DIMM socket. Place the ICE-9652/9602 on an anti-static pad. Step 2: Align the SO-DIMM with the socket. The SO-DIMM must be oriented in such a way that the notch in the middle of the SO-DIMM must be aligned with the plastic bridge in the socket.

  • Page 43: Jumper Settings

    Jumper Location: See Figure 4-2 This jumper selects which BIOS to use. There is a BIOS included on the ICE-9652/9602, but a BIOS connected to the LPC or PCI bus can be used instead. The clear CMOS jumper settings are shown in Table 4-2.

  • Page 44: Lvds Panel Resolution

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 4-2: BIOS Selection Switch Location 4.4.2 LVDS Panel Resolution Jumper Label: 4-in-1 switch Jumper Type: Jumper Settings: See Table 4-3 Jumper Location: See Figure 4-3 This switch sets the resolution of the panel attached to the LVDS output. Settings are shown in Table 4-3.

  • Page 45: Peg And Sdvo Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 4-3: LVDS Panel Resolution Selection Switch Location 4.4.3 PEG and SDVO Configuration Jumper Label: Jumper Type: 4-in-1 switch Jumper Settings: See Table 4-3 Jumper Location: See Figure 4-4 This switch configures the PEG and SDVO settings. Settings are shown in Table 4-3.

  • Page 46: Mounting The Ice-9652/9602

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 4-4: PEG and SDVO Configuration Switch Location 4.5 Mounting the ICE-9652/9602 WARNING! Never run the embedded module without an appropriate heat sink. WARNING! Please note that the installation instructions described in this manual should be carefully followed in order to avoid damage to the CPU module components and injury to the user.

  • Page 47: Figure 4-5: Ice-9652/9602 Installation

    CPU and SO-DIMM module. The ICE-9652/9602 embedded module has two standard COM Express connectors on the reverse side. To install the ICE-9652/9602 please refer to and follow the installation instructions below: Figure 4-5: ICE-9652/9602 Installation Step 1: Align the ETX connectors.
  • Page 48 Step 3: Align the heatspreader. Align the heatspreader with the ICE-9652/9602 making sure that the three onboard chipsets are in proper contact with the heatspreader. Make sure the five retention screw holes on of the heatspreader are properly aligned with the corresponding holes on the COM Express module and baseboad.

  • Page 49: Bios Setup

    ICE-9652/9602 COM Express Basic Type 2 Module Chapter BIOS Setup Page 37...

  • Page 50: Introduction

    ICE-9652/9602 COM Express Basic Type 2 Module 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways.

  • Page 51: Getting Help

    ICE-9652/9602 COM Express Basic Type 2 Module Function F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 5-1: BIOS Navigation Keys 5.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears.

  • Page 52: Main

    ICE-9652/9602 COM Express Basic Type 2 Module 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. BIOS SETUP UTILITY Main Advanced...

  • Page 53: Advanced

    ICE-9652/9602 COM Express Basic Type 2 Module The System Overview field also has two user configurable fields: System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. System Date [xx/xx/xx] Use the System Date option to set the system date.

  • Page 54: Cpu Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced Settings Configure CPU ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below sections may cause system to malfunction CPU Configuration IDE Configuration Floppy Configuration...

  • Page 55: Ide Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module Manufacturer: Lists the name of the CPU manufacturer Brand String: Lists the brand name of the CPU being used Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed Cache L1: Lists the CPU L1 cache size Cache L2: Lists the CPU L2 cache size 5.3.2 IDE Configuration...

  • Page 56: Ide Master, Ide Slave

    ICE-9652/9602 COM Express Basic Type 2 Module Enhanced Configures the on-board ATA/IDE controller to be in Enhanced mode. In this mode, IDE channels and SATA channels are separated. This mode supports up to 6 storage devices. Some legacy OS do not support this mode.

  • Page 57: Bios Menu 5: Ide Master And Ide Slave Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit Primary IDE Master Select the type of device ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ connected to the system Device :Not Detected ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Type [Auto] LBA/Large Mode [Auto]...
  • Page 58 ICE-9652/9602 COM Express Basic Type 2 Module 32Bit Data Transfer: Enables 32-bit data transfer. Type [Auto] Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from after the Power-On Self-Test (POST) is complete. Not Installed BIOS is prevented from searching for an IDE disk drive on the specified channel.
  • Page 59 ICE-9652/9602 COM Express Basic Type 2 Module Block (Multi Sector Transfer) [Auto] Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect if the device supports multi-sector transfers. Disabled BIOS is prevented from using Multi-Sector Transfer on the specified channel.
  • Page 60 ICE-9652/9602 COM Express Basic Type 2 Module Auto BIOS auto detects the DMA mode. Use this value if the IDE EFAULT disk drive support cannot be determined. Single Word DMA mode 0 selected with a maximum data SWDMA0 transfer rate of 2.1 MB/s...

  • Page 61: Floppy Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module S.M.A.R.T [Auto] Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and Reporting Technology (SMART) on the drive on the specified channel. S.M.A.R.T predicts impending drive failures. The S.M.A.R.T BIOS option enables or disables this function.

  • Page 62: Super Io Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module Floppy A/B Use the Floppy A/B option to configure the floppy disk drive. Options are listed below: Disabled 360 KB 51/4” 1.2 MB 51/4” 720 KB 31/2” 1.44 MB 31/2’ 2.88 MB 31/2”...
  • Page 63 ICE-9652/9602 COM Express Basic Type 2 Module 3F8/IRQ4 Serial Port 1 I/O port address is 3F8 and the interrupt EFAULT address is IRQ4 Serial Port 1 I/O port address is 3E8 and the interrupt 3E8/IRQ4 address is IRQ4 2E8/IRQ3 Serial Port 1 I/O port address is 2E8 and the interrupt...
  • Page 64 ICE-9652/9602 COM Express Basic Type 2 Module Parallel Port I/O port address is 278 Parallel Port I/O port address is 3BC Parallel Port Mode [Normal] Use the Parallel Port Mode option to select the mode the parallel port operates in.
  • Page 65 ICE-9652/9602 COM Express Basic Type 2 Module Serial Port3 Address [3E8] Use the Serial Port3 Address option to select the base addresses for serial port 3 No base address is assigned to serial port 3 Disabled Serial port 3 I/O port address is 3E8...
  • Page 66 ICE-9652/9602 COM Express Basic Type 2 Module Serial Port5 Address [2F0] Use the Serial Port5 IRQ option to select the interrupt address for serial port 5. No base address is assigned to serial port 5 Disabled Serial port 5 I/O port address is 2F0...

  • Page 67: Win83627Ehg Hardware Health Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module COM6 Select RS232/RS485/RS422 [RS/232] Use the COM6 Select RS232/RS485/RS422 option to select the Serial Port 6 signaling mode. RS232 Serial Port 6 signaling mode is RS-232 EFAULT Serial Port 6 signaling mode is RS-422/RS-485 RS422/RS485 5.3.5 Win83627EHG Hardware Health Configuration...

  • Page 68: Win83L784G Hardware Health

    ICE-9652/9602 COM Express Basic Type 2 Module PWM Maximum Mode: 255 The following system parameters and values are shown. The system parameters that are monitored are: Fan Speeds: The CPU cooling fan speed is monitored. System Fan Speed CPU Fan Speed Voltages: The following system voltages are monitored +3.30 Vin...
  • Page 69 ICE-9652/9602 COM Express Basic Type 2 Module System Temperatures: The following system temperatures are monitored On-Chip Temperature CPU Temperature System Temperature Fan Speeds: The CPU cooling fan speed is monitored. System Fan2 Speed Voltages: The following system voltages are monitored Vcore +3.30 Vin...

  • Page 70: Power Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module 5.3.7 Power Configuration The Power Configuration menu (BIOS Menu 10) allows the advanced power management options to be configured. BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit Power Type [ATX]...

  • Page 71: Apm Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit General ACPI Configuration Select the ACPI state ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ used for System Suspend Suspend mode [S1 (POS)] Select Screen ↑ ↓ Select Item...

  • Page 72: Bios Menu 12: Apm Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit APM Configuration Go into On/Off, or ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Suspend when Power button is pressed Power Button Mode [On/Off] Restore on AC Power Loss...
  • Page 73 ICE-9652/9602 COM Express Basic Type 2 Module Resume on Ring/PCIE Wake up [Disabled] Use the Resume on Ring/PCIE Wake up BIOS option to enable activity on the RI (ring in) modem line or on the PCI-Express bus to rouse the system from a suspend or standby state.

  • Page 74: Remote Access Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module Resume on Keyboard/Mouse [Disabled] Use the Resume on Keyboard/Mouse BIOS option to enable activity on either the keyboard or mouse to rouse the system from a suspend or standby state. That is, the system is roused when the mouse is moved or a button on the keyboard is pressed.
  • Page 75 ICE-9652/9602 COM Express Basic Type 2 Module Remote Access [Disabled] Use the Remote Access option to enable or disable access to the remote functionalities of the system. Disabled Remote access is disabled. EFAULT Remote access configuration options shown below Enabled...
  • Page 76 ICE-9652/9602 COM Express Basic Type 2 Module Serial Port Mode [115200 8,n,1] Use the Serial Port Mode option to select baud rate through which the console redirection is made. The following configuration options are available 115200 8,n,1 EFAULT 57600 8,n,1...

  • Page 77: Usb Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module 5.3.9 USB Configuration Use the USB Configuration menu (BIOS Menu 14) to read USB configuration information and configure the USB settings. BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit USB Configuration Disabled ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯...

  • Page 78: Pci/Pnp

    ICE-9652/9602 COM Express Basic Type 2 Module USB 2.0 Controller [Enabled] The USB 2.0 Controller is enabled Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded.

  • Page 79: Bios Menu 15: Pci/Pnp Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced PCI/PnP Settings Available: Specified IRQ ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ is available to be use the PCI/PnP devices WARNING: Setting wrong values in below sections Reserved: Specified IRQ...
  • Page 80 ICE-9652/9602 COM Express Basic Type 2 Module IRQ10 IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device. Available The specified DMA is available to be used by...

  • Page 81: Boot

    ICE-9652/9602 COM Express Basic Type 2 Module 5.5 Boot Use the Boot menu (BIOS Menu 16) to configure system boot options. BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Boot Settings Configure settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ during system boot. Boot Settings Configuration Select Screen ↑...

  • Page 82: Boot Settings Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module 5.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 17) to configure advanced system boot options. BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit Boot Settings Configuration Allows BIOS to skip ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯...
  • Page 83 ICE-9652/9602 COM Express Basic Type 2 Module AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed. Force BIOS The system forces third party BIOS to display EFAULT during system boot.

  • Page 84: Security

    ICE-9652/9602 COM Express Basic Type 2 Module 5.6 Security Use the Security menu (BIOS Menu 18) to set system and user passwords. BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Security Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Supervisor Password :Not Installed User Password...

  • Page 85: Chipset

    ICE-9652/9602 COM Express Basic Type 2 Module 5.7 Chipset Use the Chipset menu (BIOS Menu 19) to access the Northbridge and Southbridge configuration menus WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.

  • Page 86: Northbridge Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module 5.7.1 Northbridge Configuration Use the Northbridge Chipset Configuration menu (BIOS Menu 20) to configure the Northbridge chipset. BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit Northbridge Chipset Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Disabled...

  • Page 87: Video Function Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module PCI/IGD PCI/PEG PEG/IGD PEG/PCI EFAULT Internal Graphics Mode Select [Enable, 8 MB] Use the Internal Graphic Mode Select option to specify the amount of system memory that can be used by the Internal graphics device.

  • Page 88: Southbridge Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module Boot Display Device Use the Boot Display Device option to select the display device used by the system when it boots. Configuration options are listed below. EFAULT LVDS 5.7.2 Southbridge Configuration The Southbridge Configuration menu (BIOS Menu 22) the Southbridge chipset to be configured.

  • Page 89: Exit

    ICE-9652/9602 COM Express Basic Type 2 Module Spread Spectrum [Disabled] Use the Spread Spectrum option to reduce the EMI. Excess EMI is generated when the system clock generator pulses have extreme values. Spreading the pulse spectrum modulates changes in the extreme values from spikes to flat curves, thus reducing the EMI.
  • Page 90 ICE-9652/9602 COM Express Basic Type 2 Module Discard Changes and Exit Use the Discard Changes and Exit option to exit the BIOS configuration setup program without saving the changes made to the system. Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup program.

  • Page 91: Software Installation

    ICE-9652/9602 COM Express Basic Type 2 Module Chapter Software Installation Page 79...

  • Page 92: Available Software Drivers

    ICE-9652/9602 COM Express Basic Type 2 Module 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates.

  • Page 93: Figure 6-1: Start Up Screen

    ICE-9652/9602 COM Express Basic Type 2 Module Step 7: The screen in Figure 6-1 appears. Figure 6-1: Start Up Screen Step 8: Click ICE-9652/9602. Step 9: The list of drivers in Figure 6-2 appears.S t e p 0 : Figure 6-2: Drivers...

  • Page 94: Chipset Driver Installation

    ICE-9652/9602 COM Express Basic Type 2 Module 6.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list shown in Figure 6-2. (See Section 6.2) Step 2: Click “1-INF” Step 3: A new window opens (Figure 6-3).

  • Page 95: Figure 6-4: Chipset Driver Welcome Screen

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-4: Chipset Driver Welcome Screen Step 6: Click N to continue. Step 7: The license agreement in Figure 6-5 appears. Figure 6-5: Chipset Driver License Agreement Step 8: Read the License Agreement.

  • Page 96: Figure 6-6: Chipset Driver Read Me File

    ICE-9652/9602 COM Express Basic Type 2 Module Step 9: Click the Y button to accept the license agreement and continue. Step 10: The Read Me file in Figure 6-6 appears. Figure 6-6: Chipset Driver Read Me File Step 11: Click N in Figure 6-6 to start the driver installation.

  • Page 97: Vga Driver Installation

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-7: Chipset Driver Installation Complete Step 13: Click F to exit the InstallShield Wizard. Step 0: INISH 6.4 VGA Driver Installation To install the VGA driver, please do the following. Step 1: Access the driver list shown in Figure 6-2.

  • Page 98: Figure 6-8: Select The Operating System

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-8: Select the Operating System Step 4: Select the operating system from those shown in Figure 6-8. Step 5: A new window appears (Figure 6-9). Figure 6-9: GMA Driver Step 6: Click the installation program icon in Figure 6-9.

  • Page 99: Figure 6-10: Gma Driver Readme File

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-10: GMA Driver Readme File Step 8: Click N to extract the GMA driver files. See Figure 6-11. Step 9: The installation files are extracted. See Figure 6-11. Figure 6-11: GMA Driver File Extraction Step 10: The Welcome Screen in Figure 6-12 appears.

  • Page 100: Figure 6-12: Gma Driver Installation Welcome Screen

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-12: GMA Driver Installation Welcome Screen Click N to continue. Step 11: The license agreement in Figure 6-13 appears. Figure 6-13: GMA Driver License Agreement Step 12: Read the License Agreement. Step 13: Click Y to accept the license agreement and continue.

  • Page 101: Lan Driver Installation

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-14: GMA Driver Installing Notice Step 15: . A confirmation screen shown in Figure 6-15 appears. Figure 6-15: GMA Driver Installation Complete Step 16: Select “Yes, I want to restart the computer now” and click F .

  • Page 102: Figure 6-16: Access Windows Control Panel

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-16: Access Windows Control Panel Step 4: Open the Realtek directory in Figure 6-16. Step 5: The screen in Figure 6-17 appears. Figure 6-17: Double Click the System Icon Step 6: Open the RTL8111C(P) directory in Figure 6-17.

  • Page 103: Figure 6-18: Click The Device Manager Button

    ICE-9652/9602 COM Express Basic Type 2 Module Step 7: The screen in Figure 6-18 appears. Figure 6-18: Click the Device Manager Button Step 8: In Figure 6-18 select the operating system. Step 9: The screen in Figure 6-19 appears. Figure 6-19: Device Manager List...

  • Page 104: Figure 6-20: Pcie Controller Driver Installation Icon

    ICE-9652/9602 COM Express Basic Type 2 Module Step 10: Open the PCIE_Install directory shown in Figure 6-19. Step 11: The screen in Figure 6-20 appears. Figure 6-20: PCIe Controller Driver Installation Icon Step 12: Double click the Setup icon in the screen in Figure 6-20 Step 13: The Welcome screen in Figure 6-21 appears.

  • Page 105: Figure 6-22: Ready To Install

    ICE-9652/9602 COM Express Basic Type 2 Module Step 14: Click N to continue. Step 15: The Ready to Install screen in Figure 6-22 appears. Figure 6-22: Ready to Install Step 16: Click N to proceed with the installation. Step 17: The program begins to install.

  • Page 106: Realtek Hd Audio Driver (Alc883) Installation

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-23: LAN Driver Installation Step 19: When the driver installation is complete, the screen in Figure 6-24 appears. Figure 6-24: LAN Driver Installation Complete Step 20: Click F to exit the InstallShield Wizard (Figure 6-24).

  • Page 107: Bios Setup

    ICE-9652/9602 COM Express Basic Type 2 Module NOTE: This driver only needs to be installed if an external audio kit with a RealTek ALC883 codec is installed. 6.6.1 BIOS Setup Step 1: Enter the BIOS setup. To do this, reboot the system and press D during POST.

  • Page 108: Figure 6-25: Select The Audio Codec

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-25: Select the Audio CODEC Step 3: Double-click the ALC883 folder. Step 4: Double-click the appropriate operating system folder (Figure 6-26). Page 96...

  • Page 109: Figure 6-26: Select The Os

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-26: Select the OS Step 5: Double-click the appropriate operating system version folder (Figure 6-27). Figure 6-27: Select the OS Version Step 6: Double-click the Setup.exe program icon in Figure 6-28. Page 97...

  • Page 110: Figure 6-28: Locate The Setup Program Icon

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-28: Locate the Setup Program Icon Step 7: The InstallShield Wizard starts (Figure 6-29). Figure 6-29: The InstallShield Wizard Starts Step 8: The InstallShield Wizard is prepared to guide the user through the rest of the process (Figure 6-30).

  • Page 111: Figure 6-30: Preparing Setup Screen

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-30: Preparing Setup Screen Step 9: Once initialized, the InstallShield Wizard welcome screen appears (Figure 6-31). Figure 6-31: InstallShield Wizard Welcome Screen Step 10: Click N to continue the installation. Step 11: InstallShield starts to install the new software as shown in Figure 6-32.

  • Page 112: Figure 6-32: Audio Driver Software Configuration

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-32: Audio Driver Software Configuration Step 12: The Installation Wizard updates the system as shown in Figure 6-33. Figure 6-33: Installation Wizard Updates the System Step 13: After the driver installation process is complete, a confirmation screen appears (Figure 6-34).

  • Page 113: Intel ® Matrix Storage Manager Driver Installation

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-34: Restart the Computer Step 14: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click F INISH restart the computer.

  • Page 114: Figure 6-35: Installshield Wizard Setup Screen

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-35: InstallShield Wizard Setup Screen Step 4: Figure 6-36 shows the Matrix Storage Manager software configuring the installation process. Figure 6-36: Matrix Storage Manager Setup Screen Step 5: Figure 6-37 shows the Matrix Storage Manager welcome screen.

  • Page 115: Figure 6-37: Matrix Storage Manager Welcome Screen

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-37: Matrix Storage Manager Welcome Screen Step 6: Click N and a warning appears (Figure 6-38). Read the warning carefully and decide whether or not to continue the installation process. Figure 6-38: Matrix Storage Manager Warning Screen...

  • Page 116: Figure 6-39: Matrix Storage Manager License Agreement

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-39: Matrix Storage Manager License Agreement Step 8: Read the license agreement. To accept the terms and conditions stipulated in the license agreement shown, click Y and the Readme information file shown in Figure 6-40 appears.

  • Page 117: Ide Controller Installation

    ICE-9652/9602 COM Express Basic Type 2 Module Step 10: After the driver installation process is complete, a confirmation screen appears (Figure 6-41). Figure 6-41: Matrix Storage Manager Setup Complete Step 11: The confirmation screen offers the option of restarting the computer now or later.

  • Page 118: Figure 6-42: Access Windows Control Panel

    ICE-9652/9602 COM Express Basic Type 2 Module Figure 6-42: Access Windows Control Panel Page 106...

  • Page 119: Figure 6-43: Double Click The System Icon

    ICE-9652/9602 COM Express Basic Type 2 Module Step 2: Double-click the System icon (Figure 6-43). Figure 6-43: Double Click the System Icon Page 107...

  • Page 120: Figure 6-44: Click The Device Manager Button

    ICE-9652/9602 COM Express Basic Type 2 Module Step 3: Click the Device Manager button under the Hardware tab (Figure 6-44). Figure 6-44: Click the Device Manager Button Page 108...

  • Page 121: Figure 6-45: Device Manager List

    ICE-9652/9602 COM Express Basic Type 2 Module Step 4: A list of system hardware devices appears (Figure 6-45). Figure 6-45: Device Manager List Step 5: The Device will be listed under “Other Devices” (This means Windows does not recognize the device) as an “IDE Device”.

  • Page 122: Figure 6-46: Hardware Update Wizard

    ICE-9652/9602 COM Express Basic Type 2 Module Step 7: The Device Driver Wizard appears (Figure 6-46). Figure 6-46: Hardware Update Wizard Step 8: Select “No, not this time” and click N to continue. Page 110...

  • Page 123: Figure 6-47: Automatic Or Manual Installation

    ICE-9652/9602 COM Express Basic Type 2 Module Step 9: A new window (Figure 6-47) appears. Figure 6-47: Automatic or Manual Installation Step 10: Select “Install from a list or specific location (Advanced)” and then click N Page 111...

  • Page 124: Figure 6-48: Select Driver Location

    ICE-9652/9602 COM Express Basic Type 2 Module Step 11: The Locate Driver Files window (Figure 6-48) appears. Figure 6-48: Select Driver Location Step 12: Select “Don’t search. I will choose the driver to install” and click N continue. Page 112...

  • Page 125: Figure 6-49: Select Driver Location

    ICE-9652/9602 COM Express Basic Type 2 Module Step 13: The Select Driver Location window (Figure 6-49) appears. Figure 6-49: Select Driver Location Step 14: Click on “Have Disk…” Step 15: The Install From Disk window (Figure 6-50) appears. Figure 6-50: Install From Disk Step 16: Click on “Browse…”...

  • Page 126: Figure 6-51: Locate File

    ICE-9652/9602 COM Express Basic Type 2 Module Step 17: The Locate File window (Figure 6-51) appears. Figure 6-51: Locate File Step 18: Choose the correct OS, click on the latest driver and then click “Open” Step 19: The Install From Disk window (Figure 6-52) appears again.

  • Page 127: Ismm Installation

    ICE-9652/9602 COM Express Basic Type 2 Module 6.9 iSMM Installation The iSMM (Intelligent System Management Module) allows hardware functions to be monitored from within the operating system. The iSMM can be set to sound an alarm when voltages, temperatures or fan speeds rise above or fall below the set limits.

  • Page 128: Figure 6-55: Ismm Installshield Welcome Screen

    ICE-9652/9602 COM Express Basic Type 2 Module Step 7: The iSMM InstallShield Welcome Screen appears. (Figure 6-55) Figure 6-55: iSMM InstallShield Welcome Screen Step 8: Click N to continue. Step 9: The License Agreement screen appears. (Figure 6-56) Figure 6-56: iSMM License Agreement...

  • Page 129: Figure 6-57: Ismm Customer Information

    ICE-9652/9602 COM Express Basic Type 2 Module Step 10: Select “I accept the terms of the license agreement.” (Figure 6-56) Step 11: Click N to continue.(Figure 6-56) Step 12: The Customer Information screen appears.(Figure 6-57) Figure 6-57: iSMM Customer Information Step 13: Fill in the “User Name”...

  • Page 130: Figure 6-58: Ismm Setup Type

    ICE-9652/9602 COM Express Basic Type 2 Module Step 15: The Setup Type screen appears. (Figure 6-58) Figure 6-58: iSMM Setup Type Step 16: Select “Complete” (Figure 6-58) Step 17: Click N to continue. (Figure 6-58) Page 118...

  • Page 131: Figure 6-59: Ismm Installation Confirmation

    ICE-9652/9602 COM Express Basic Type 2 Module Step 18: The Installation Confirmation screen appears. (Figure 6-59) Figure 6-59: iSMM Installation Confirmation Step 19: Click I to begin installing the drivers. (Figure 6-59) NSTALL Page 119...

  • Page 132: Figure 6-60: Ismm Installshield Wizard Complete

    ICE-9652/9602 COM Express Basic Type 2 Module Step 20: The InstallShield Wizard Completed appears when the drivers are finished installing. (Figure 6-60) Figure 6-60: iSMM InstallShield Wizard Complete Step 21: Click F to exit the installation program.(Figure 6-60) INISH Step 22: The Restart Confirmation screen appears.(Figure 6-61)

  • Page 133: Abios Options

    ICE-9652/9602 COM Express Basic Type 2 Module Appendix BIOS Options Page 121...
  • Page 134 ICE-9652/9602 COM Express Basic Type 2 Module Below is a list of BIOS configuration options in the BIOS chapter. 　 System Overview .........................40 　 System Time [xx:xx:xx] .......................41 　 System Date [xx/xx/xx] ......................41 　 ATA/IDE Configurations [Compatible]................43 　 Legacy IDE Channels [PATA Pri, SATA Sec] ..............44 　...
  • Page 135 ICE-9652/9602 COM Express Basic Type 2 Module 　 Suspend Mode [S1(POS)]....................59 　 Power Button Mode [On/Off]....................60 　 Restore on AC Power Loss [Last State] ................60 　 Resume on Ring/PCIE Wake up [Disabled]...............61 　 Resume on PME# [Disabled] ....................61 　 Resume On RTC Alarm [Disabled]..................61 　...
  • Page 136 ICE-9652/9602 COM Express Basic Type 2 Module 　 Discard Changes and Exit....................78 　 Discard Changes........................78 　 Load Optimal Defaults......................78 　 Load Failsafe Defaults......................78 Page 124...

  • Page 137: B Terminology

    ICE-9652/9602 COM Express Basic Type 2 Module Appendix Terminology Page 125...
  • Page 138 ICE-9652/9602 COM Express Basic Type 2 Module AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface.
  • Page 139 ICE-9652/9602 COM Express Basic Type 2 Module Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are types of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module.
  • Page 140 ICE-9652/9602 COM Express Basic Type 2 Module Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer.

  • Page 141: C Watchdog Timer

    ICE-9652/9602 COM Express Basic Type 2 Module Appendix Watchdog Timer Page 129...
  • Page 142 ICE-9652/9602 COM Express Basic Type 2 Module NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash.
  • Page 143 ICE-9652/9602 COM Express Basic Type 2 Module NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE PROGRAM: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds...

  • Page 144: D Compatibility

    ICE-9652/9602 COM Express Basic Type 2 Module Appendix Compatibility Page 132...

  • Page 145: Compatible Operating Systems

    The compatible items described here have been tested by the IEI R&D team and found to be compatible with the ICE-9652/9602 D.1 Compatible Operating Systems The following operating systems have been successfully run on the ICE-9652/9602. MS-DOS 6.22 Microsoft Windows XP Professional with SP2 D.2 Compatible Processors...

  • Page 146: Compatible Memory Modules

    The memory modules listed below have been tested on the ICE-9652/9602 other memory modules that comply with the specifications may also work on the ICE-9652/9602 but have not been tested. The following memory modules have been successfully tested on the ICE-9652/9602.

  • Page 147: E Hazardous Materials Disclosure

    ICE-9652/9602 COM Express Basic Type 2 Module Appendix Hazardous Materials Disclosure Page 135...

  • Page 148: Hazardous Materials Disclosure Table For Ipb Products Certified As Rohs Compliant Under 2002/95/Ec Without Mercury

    ICE-9652/9602 COM Express Basic Type 2 Module E.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
  • Page 149 ICE-9652/9602 COM Express Basic Type 2 Module Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Biphenyls Diphenyl (Pb) (Hg) (Cd) Chromium (CR(VI)) (PBB) Ethers (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly...
  • Page 150 ICE-9652/9602 COM Express Basic Type 2 Module 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些 元件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 显示 印刷电路板 金属螺帽 电缆组装 风扇组装 电力供应组装 电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。...

This manual is also suitable for:

Ice-9602

Table of Contents