• When unpacking the appliance, check that it • During high temperature wash programmes is not damaged. If in doubt, do not use it and the door glass may get hot. Do not touch it! contact the Service Centre. www.zanussi.com...
Page 3
If volatile cleaning fluids is horizontal. If neces- wise until the groove are used, care should be taken to ensure that sary use a coin. is vertical. the fluid is removed from the garment before placing in the machine. www.zanussi.com...
Follow the product manufacturer’s recommendations on quantities to use and do not exceed the «MAX» mark in the detergent dispenser drawer. Any fabric softener or starching additives must be poured into the compartment before starting the wash programme. www.zanussi.com...
A cycle to be used for daily soiled cotton, syn- thetic or delicate items in order to obtain good Programme Selector Dial washing performance in a short time. It allows you to switch the appliance on/off and/ or to select a programme. www.zanussi.com...
COTTON SPIN Normal NO SPIN INTENSIVE 90° - (Cold) Main wash - Rinses SUPER QUICK DAILY Maximum spin speed 800 rpm Max. load 6 kg - Reduced load 3 kg EXTRA RINSE White and coloured cotton (normally soiled items). www.zanussi.com...
Page 7
60° - (Cold) SUPER QUICK Prewash - Main wash - Rinses Maximum spin speed 800 rpm DAILY EXTRA RINSE Max. load 3 kg - Reduced load 1.5 kg Synthetic or mixed fabrics: underwear, coloured gar- ments, non-shrink shirts, blouses. www.zanussi.com...
Page 8
Max. load 6 kg With this programme it is possible to rinse and spin cotton garments which have been washed by hand. The machine performs some additional rinses, followed by a final long spin. The spin speed can be reduced. www.zanussi.com...
Energy con- Water con- Approximate Remaining Programmes (kg) sumption sumption (litre) programme moisture (kWh) duration (mi- nutes) Cottons 60 °C 1.30 Cottons 40 °C Synthetics 40 °C Delicates 40 °C 0.55 Wool/Hand wash 0.25 30 °C Standard cotton programmes www.zanussi.com...
(e.g. hair clips, safety pins, lay the garment on a soft surface and dab the pins). stain with the fingertips and a cotton cloth. Button up pillowcases, close zip fasteners, hooks and poppers. Tie any belts or long tapes. www.zanussi.com...
• Remove the polystyrene block and any connections comply with the installation material from the drum. instructions. • Pour 2 litres of water into the main wash compartment of the detergent draw- 1) do not use acetone on artificial silk www.zanussi.com...
6 will blink 3 times to indicate a wrong selection. The machine will not perform the new selected programme. Select the required temperature by turning the temperature selector dial (2) Turn clockwise this dial to select the more con- venient to your laundry washing temperature. www.zanussi.com...
Page 13
Interrupting a programme luminates. Press the button 6 to interrupt a programme You must select this option after you have set which is running, the corresponding green pilot the programme and before you start the pro- light starts blinking. gramme. www.zanussi.com...
Do this separately from any laundry washing, and according to the soft- ening powder manufacturer's instructions. This will help to prevent the formation of lime depos- its. www.zanussi.com...
Page 15
(it rotates jerkily). If it doesn’t rotate, switch the appliance off and remove the please contact the Service. mains plug from the socket. Proceed as follows: • Unplug the appliance. • If it is necessary, wait until the water has cooled down. www.zanussi.com...
Page 16
6. when the drain pump is empty, install the sure the connection is tight. water inlet hose again. Warning! Make sure that the temperature is more than 0 °C before you use the appliance again. The manufacturer is not responsible for dam- ages caused by low temperatures. www.zanussi.com...
6 to restart the programme. If after few seconds. The red button 6 light will flash all checks, the problem persists, contact your for a short time as described (the green flash is local Service Centre. not to be considered) : www.zanussi.com...
Page 18
• Check the water inlet hose connection. The drain or inlet hose is damaged. • Replace it with a new one. The filter of the drain pump has not been properly screwed in after cleaning action. • Screw the filter fully in. www.zanussi.com...
Page 19
No water is visible in the Machines based on modern technology operate very economically using drum: very little water without affecting performance. www.zanussi.com...
Remove the power supply cable and the ho- ses from the hose holders on the rear of the appliance. Remove the polystyr- After removing all the ene base from the packaging, carefully bottom. lay machine on it's back. www.zanussi.com...
Page 21
Caution! Do not use the hose from your adjust as they incor- previous appliance to connect to water porate a self locking supply. nut, but the machine MUST be level and stable. If necessary, check the setting with a spirit level. www.zanussi.com...
Check that your domestic electrical installation Caution! The power supply cable can take the maximum load required, also tak- must be easily accessible after ing into account any other appliances in use. installing the machine. www.zanussi.com...
Packaging materials then be washed at a lower temperature. The materials marked with the symbol • Measure out detergent according to the wa- recyclable. ter hardness, the degree of soiling and the >PE<=polyethylene quantity of laundry being washed. >PS<=polystyrene www.zanussi.com...