Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Savant SmartMediaPro 6
Summary of Contents for Savant SmartMediaPro 6
- Page 1 SmartMediaPro 6 / SmartMedia Pro 12 SSP-0600 | SSP-1200 | SSP-1200R Deployment Guide Document Number: 009-0418-05 Document Date: September 2017 Document Supports: da Vinci 4.3.2 SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920...
-
Page 2: Table Of Contents
Important Notice .................... 32 7.4. GPIO Port Connections ................... 16 7.5. HDMI Port Connections .................. 16 7.6. AC Power Connection ..................17 SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 3: Important Safety Information - Read First
Important Safety Information – Read First Before installing, configuring, and operating Savant® equipment and other vendor equipment, Savant recommends that each dealer, installer, or integrator, access and read all the required technical documentation. Savant technical documentation can be located by visiting the Savant Customer Community. Vendor documentation is supplied with the equipment. -
Page 4: Introduction
This Deployment Guide will guide the installer through the process of installing, configuring, and adding a SmartMediaPro chassis to a Blueprint configuration. While this document contains all the steps required, other information may be required during the process. Please visit the Savant Customer Community for additional information. -
Page 5: Checklist
Fan Tray Removal and Installation SSP-1200R Power Supply Removal and Installation SSP-1200R 7. Appendix A – Network Requirements ..........................Appendix A: Network Requirements SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 6: Front And Rear Panel Descriptions
Green: Indicates activity on the associated control type port. Control ports are located on the back panel. Status LEDs Control Ports - RS-232/422/485, IR, and GPIO SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... - Page 7 100 – 240V AC 3A 50/60 Hz (On): Powers On the controller. I/O (power switch) (Off): Powers Off the controller. Fuse 250V 3A Fast acting (field replaceable) SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920...
-
Page 8: Smartmedia 12 (Ssp-1200/1200R)
Green: Indicates activity on the associated control type port. Control ports are located on the back panel. Control Status LEDs Control Ports - RS-232/422/485, IR, and GPIO SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... - Page 9 250V 5A Fast acting (field replaceable) (On): Powers On the controller. I/O (power switch) (Off): Powers Off the controller. Power Input 100 – 240V AC 5A 50/60 Hz SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920...
-
Page 10: Module Installation And Removal (Audio/Video Cards)
SSP-0600 Rear Panel SSP-1200 / 1200R Rear Panel NOTE: Slot Expansion is used by some legacy output modules . SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 11: Module Installation And Removal Precautions
The modules (audio and video cards) can be installed either before or after installing chassis into a rack system. Because it is sometimes difficult to get to the rear panel, Savant recommends installing the modules before installing into a rack system. Follow the steps below to install the modules into an SSP- 0600or SSP-1200 chassis. -
Page 12: Module Removal
IMPORTANT! If the module is not being replaced, install a blank plate using the two (2) M3 x 6 mm screws removed in step 2. This will ensure that proper airflow through the chassis is retained as well as preventing dust and debris from entering the chassis. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC... -
Page 13: Rack Installation
Before assigneing the IP Address, the Control Ports must be wired. Continue to the next section (Control Port Connections) for information on this. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 14: Control Port Connections
- CTS/RTS handshaking is supported for flow control based on the profile used in the configuration. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 15: Ir Port Connections
Relay ports are used when a device is controlled via a normally open (NO) or normally closed (NC) relay. The Relay port connections below pertain to both the SSP-0600 and SSP-1200 SmartMediaPro Chassis. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC... -
Page 16: Gpio Port Connections
7.4. GPIO Port Connections General Purpose Input/Outputs (GPIO) are binary I/O ports used on Savant controllers to trigger an action within the system. Events can control a device, such as turning on an amplifier (output) or detecting a state change for a device (input) to perform a workflow. Pins 2-8 are used for input or output depending on the configuration. -
Page 17: Ac Power Connection
POWER MANAGEMENT RECOMMENDATION Savant recommends a pure sine wave uninterruptible power supply (UPS) with the ability to shut down the Savant Host before the battery runs out of power. Never remove power from the Savant Host before shutting it down. -
Page 18: Racepoint Blueprint Configuration
- Amplifiers for audio distribution - HDTV displays - Speakers - Savant Host The Blueprint layout shown below is for reference only! SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 19: Add Smartmedia Controller
Show Inspector icon from the Blueprint toolbar. 7. Enter the UID for the SmartMediaPro chassis into the UID field of the Inspector. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 20: Add Modules (Service Cards)
3. Drag and drop the selected card into an open input or output slot 4. Repeat step 3 until all modules required are placed in the appropriate input or output slot. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 21: Remove A Module
The SmartMediaPro chassis supports adding an Audio Interrupt Service (AIS). The Audio Interrupt can be configured to interrup a currently playing audio with a doorbell chime thus allerting the user that the doorbell was pressed. This service requires a connection between a Savant host and the SmartMediaPro chassis. -
Page 22: Add A Connection To Stream Itunes (Da Vinci 8.0.2 Or Lower)
4. Select the Generate Services icon from the Blueprint toolbar. 5. Select View Services icon from Blueprint. Verify the iTunes Service got created. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... - Page 23 Mini Display Port to HDMI Adapter (not included). - Refer to the iTunes Media Server Programming Guide on the Savant Customer Community for more information on configuring iTunes SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright ©...
-
Page 24: Upload Configuration To Host
5. The System Monitor - Scanner application will automatically open as displayed below. Verify the path to the configuration file is correct. Select Upload when satisfied. 6. The configuration will upload to the Host. Once upload is complete, the Savant Pro or TrueControl II application can be opened. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright ©... -
Page 25: Chassis Maintenance
6. Gently place the new fuse in the cartridge and place the cartridge part way remove it, verify the orientation, and repeat step. into the receptacle aligning it as defined in the diagram. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 26: Fan Tray Removal/Installation Ssp-1200
8. Tighten the fan tray retaining screw to secure to the chassis. Do Not Overtighten. 9. Reinstall front cover. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 27: Fan Tray Removal/Installation Ssp-1200R
8. Set the plastic corner piece removed in step 3 back into its initial position and reinstall the two screws. Do Not Overtighten. 9. Reinstall front cover. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 28: Power Supply Removal/Installation Ssp-1200R
7. Install the two screws to secure to the front panel. Do Not Overtighten. 8. Install front cover. SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright © 2017 Savant Systems, LLC 009-0418-05 | 170920... -
Page 29: Additional Information
11. Additional Information Refer to the following documents located on the Savant Customer Community for additional information. - SmartMediaPro 12 (SSP-1200-xx) Quick Reference Guide - SmartMedia Pro 6 (SSP-0600-xx) Quick Reference Guide - SmartMediaPro 12 with Redundant Power Supplies (SSP-1200R-xx) Quick Reference Guide SmartMediaPro 6 and SmartMediaPro 12 Deployment Guide Copyright ©... -
Page 30: Appendix A: Network Requirements
These higher quality components also allow for more accurate troubleshooting when needed. Connect all Savant devices to the same local area network (LAN) or subnet as the Host. Savant recommends not implementing any type of traffic or packet shaping in your network topology for the Savant devices as this may interfere with performance. -
Page 31: Appendix B: Uninterruptible Power Supply (Ups)
Appendix B: Uninterruptible Power Supply (UPS) Savant does not recommend any particular brand or model UPS, however there are a couple of factors that should be considered. It is important that the UPS does not only work during complete power loss but protects devices and their functionality during events like surges and brownouts. It is not uncommon for a residence or small business to see variations in power service that do not result in a complete black-out. -
Page 32: Important Notice
The contents of this document are subject to change without notice; therefore, the information presented herein shall not be construed as a commitment or warranty. Savant Systems, LLC shall not be liable for any technical or editorial errors or omissions contained herein or for incidental or consequential damages resulting from the performance, furnishing, reliance on, or use of this material.
Need help?
Do you have a question about the SmartMediaPro 6 and is the answer not in the manual?
Questions and answers