primatech 534FN Operating Instructions Manual
  1. Manuals
  2. Brands
  3. primatech Manuals
  4. Nail Gun
  5. 534FN
  6. Operating instructions manual

primatech 534FN Operating Instructions Manual

Finish nailer
Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
The Primatech 534FN is a professional heavy duty pneumatic finish nailer designed to drive
standard 34° strips of 15
Read carefully these instructions before operating this tool. It is important to understand
warnings/cautions and the safety measures to ensure safe use of this tool. Additional
information is available directly from:
1135 Jérémie-Fortin,
Québec, QC
Canada, G1J 1R8
IMPORTANT SAFETY INSTRUCTIONS
There are certain applications for which this tool was designed. We strongly recommend that
this tool SHALL NOT be modified and /or used for any application other than for which it was
designed.
WARNING: When using pneumatic tools, basic safety precautions should always be followed
to reduce the risk of personal injury, including the following:
• KEEP WORKING AREA CLEAN. Cluttered areas
invite injuries.
• DON'T ALLOW CHILDREN IN THE WORKING
AREA. Don't let them handle the tool.
• USE SAFETY GLASSES. To prevent eye injuries,
the tool operator and all persons in the working are
a must wear safety glasses with permanently
attached, rigid, plastic side shields. These safety
glasses must conform to ANSI Z87.1 requirements
(approved glasses have " Z87" printed or stamped
on them).
• USE EAR PROTECTION. The working area may
be exposed to high noise levels that can lead to
hearing damage.

OPERATING INSTRUCTIONS

nails in lengths of 1-1/4" (32mm) to 2-1/2" (64mm).
GA
Phone:
Fax:
email:
web:
534FN
FINISH NAILER
1 (800) 363-1962 or 1 (418) 522-7744
1 (418) 522-7466
support@primatech.ca
support.primatech.ca

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 534FN and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for primatech 534FN

Summary of Contents for primatech 534FN

  • Page 1: Operating Instructions

    534FN FINISH NAILER OPERATING INSTRUCTIONS The Primatech 534FN is a professional heavy duty pneumatic finish nailer designed to drive standard 34° strips of 15 nails in lengths of 1-1/4" (32mm) to 2-1/2" (64mm). Read carefully these instructions before operating this tool. It is important to understand warnings/cautions and the safety measures to ensure safe use of this tool.
  • Page 2 WARNING LABEL. If label is missing, damaged or unreadable, contact your local agencies. • ONLY USE PARTS AND FASTENERS recommended by Primatech. • CONNECT TOOL TO AIR SUPPLY BEFORE LOADING FASTENERS, to prevent a fastener from being fired during connection. The tool driving mechanism may cycle when tool is connected to the air supply.
  • Page 3 • DO NOT LOAD FASTENERS with trigger or safety depressed, to prevent unintentional firing of a fastener. • REMOVE FINGER FROM TRIGGER when not driving fasteners. Never carry tool with finger on trigger: tool will fire a fastener if safety is bumped while trigger is depressed.

  • Page 4: Air Supply

    This nailer is equipped with a safety contact and will not operate unless the safety contact is depressed against the work piece. The 534FN can be operated in two different ways: trigger fire (single sequential) or bump fire (contact actuation).
  • Page 5 Trigger firing (single sequential): Rotate the selector upwards as shown on Fig. 18A. Position the nose on the working surface and lightly push the tool downward until the safety contact is depressed, then, pull the trigger to drive the fastener. Allow tool to recoil off the surface to avoid a second unwanted fastener to be fired.

  • Page 6: Clearing A Jammed Fastener

    SERVICE AND REPAIRS Disassembly of the tool must be done in a clean environment. Some parts can be easily damaged if disassembled with improper tools or by inadequatemethods. Maintenance should only be performed by trained personnel. Use only genuine PRIMATECH replacement parts.

  • Page 7: Troubleshooting

    Incorrect or damaged – Use approved fasteners of correct gage and size. Magazine or nose screws loose – Tighten all screws. Magazine is dirty – Clean magazine. Replace worn or damaged driver. Consult our on-line Technical Support site at support.primatech.ca for updated documents and more tips.

Table of Contents