Advertisement
KX-TGA523CE_OI 04.4.28 11:32 ページ 3
2
Listening to the Radio
Memory Buttons
([M1], [M2], [M3], [M4] and [M5])
[+, -, TUNE/CLOCK]
[OFF]
[FM/AM, RADIO]
2-A Manual Tuning
1
Press [FM/AM, RADIO] to turn the radio
on.
2
Press [FM/AM, RADIO] to switch
between FM and AM.
3
Tune in to the desired station by pressing
[+, TUNE/CLOCK] or [–, TUNE/CLOCK].
•Press and hold [+] or [–] to search faster.
4
Adjust the volume using the VOLUME control.
To turn the radio off
Press [OFF].
2-B Preset Tuning
You can assign one FM station and one AM station to each of the 5
memory buttons ([M1], [M2], [M3], [M4] and [M5]) for a total of 10
stations.
To preset stations
1
Press [FM/AM, RADIO] to turn the radio on.
2
Press [FM/AM, RADIO] to switch between FM and AM.
3
Tune in to the desired station by pressing
[+, TUNE/CLOCK] or [–, TUNE/CLOCK].
•Press and hold [+] or [–] to search faster.
4
Press and hold a memory button ([M1] to
[M5]) until the memory number is
displayed.
•To turn the radio off, press [OFF].
•If you assign another station of the same band (FM or AM) to the
memory button, the previously assigned station will be erased.
•If a power failure occurs, station presets will be retained for about 10
minutes.
To listen to preset stations
1
Press [FM/AM, RADIO] to turn the radio on.
2
Press [FM/AM, RADIO] to switch between FM and AM.
3
Press the desired memory button ([M1] to [M5]).
•To turn the radio off, press [OFF].
[SNOOZE/MUTE]
VOLUME Control
Loud
e.g. Memory Number 1
2-C Improving Reception
For FM
Extend the cord and place
the antenna in a location
where reception improves.
2-D Muting the Radio
Press [SNOOZE/MUTE] while listening to the radio.
•"
" flashes on the display.
•To release the mute, press [SNOOZE/MUTE] again.
2-E Changing the FM Tuning Sensitivity
You can change the sensitivity used for tuning in FM stations
from 0.2 MHz (factory preset) increments to 0.1 MHz.
•Note that if you change the sensitivity, all FM station presets (2-B)
and the station used for the radio alarm (4-A) will return to the
factory preset. The buzzer will sound at the set radio alarm time.
1. Press [FM/AM, RADIO] to turn the radio on.
2. Press [FM/AM, RADIO] to switch to the FM band.
3. Press and hold [FM/AM, RADIO] for about 5 seconds.
•The display changes to show the lowest available FM frequency.
•To change the sensitivity back to 0.2 MHz increments, repeat the
procedure above.
•If the AM band is selected and you press and hold [FM/AM,
RADIO] for about 5 seconds, the band will change to FM but the
FM tuning sensitivity will not change.
3
Using the Sleep Timer
3-A Setting the Sleep Timer
The sleep timer turns the radio off
after a set time.
[SLEEP]
While the radio is on, press [SLEEP]
repeatedly to select the time (minutes).
•Each time you press [SLEEP], the time
will change as follows:
30
60
90
120
OFF
•The radio will automatically turn off after the selected sleep time.
•You cannot set the sleep timer while an alarm is sounding (4-A,
4-B).
To view the time remaining:
To change the setting
1. Press [SLEEP]. (The time remaining is displayed.)
2. Immediately after the time remaining is displayed, press [SLEEP]
repeatedly to select the sleep time.
Section 2
For AM
Reorient the antenna horizontally
until reception improves.
Section 3
e.g. Sleep Time: 30 min.
Press [SLEEP].
Advertisement
