Acer Aspire X1301 Service Manual

Acer laptop user manual
Hide thumbs

Advertisement

Table of Contents
Acer
Aspire X1300/X1301
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to
http://csd.acer.com.tw
PRINTED IN TAIWAN

Advertisement

Table of Contents
loading

  Also See for Acer Aspire X1301

  Related Manuals for Acer Aspire X1301

  Summary of Contents for Acer Aspire X1301

  • Page 1 Acer Aspire X1300/X1301 Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.tw PRINTED IN TAIWAN...
  • Page 2: Revision History

    Revision History Please refer to the table below for the updates made on ASX1300 service guide. Date Chapter Updates...
  • Page 3 Copyright Copyright © 2009 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without...
  • Page 4 Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
  • Page 5 Conventions The following conventions are used in this manual: SCREEN MESSAGES NOTE WARNING CAUTION IMPORTANT Denotes actual messages that appear on screen. Gives additional information related to the current topic. Alerts you to any physical risk or system damage that might result from doing or not doing specific actions.
  • Page 6: Fru Information

    Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
  • Page 7: Table Of Contents

    Table of Contents Table of Contents vii System Tour 1 Features 1 Aspire X1300/X1301 Tour 3 Front Pane 3 Rear Panel 5 Internal Components System LED Indicators 7 System Utilities 9 Phoenix BIOS Setup Utility Entering BIOS setup Navigating Through the Setup Utility 10 Setup Utility Menus 11 System Disassembly 33 Disassembly Requirements 33...
  • Page 8 viii...
  • Page 9: System Tour

    System Tour Features Below is a brief summary of the computer’s many feature: NOTE: The features listed in this section is for your reference only. The exact configuration of the server depends on the model purchased. Processor AMD Athlon LE-1600/1620/1640 processor •...
  • Page 10: Operating System And Software

    Operating system options: • Genuine Windows Vista • Genuine Windows Vista Home Premium (32/64-bit) • Applications • Acer Empowering Technology (Acer eRecovery Management) • Acer Arcade Live • McAfee Internet Security Suite 2008 Trial version • Adobe Reader • eSobi •...
  • Page 11: Aspire X1300/X1301 Tour

    Aspire X1300/X1301 Tour This section is a virtual tour of the ASX1300 system’s interior and exterior components. Front Pane Item Icon Chapter 1 Component Drive bay door Drive bay door eject button Press to open drive bay door and access the optical drive. Media card reader USB 2.0 ports...
  • Page 12 Item Icon Component Headphone/Speaker-out/line-out jack Microphone-in jack CF I/II (CompactFlash Type I/II) slot IEEE 1394 port (4-pin) Power/sleep button Chapter 1...
  • Page 13: Rear Panel

    Rear Panel Item Icon SPDIF ESATA HDMI Chapter 1 Component Expansion slot (Photo shows graphics card and network/modem card) Line-out jack Microphone/speaker-out/line-in jack S/PDIF port USB 2.0 ports eSATA port CRT/LCD monitor port HDMI port PS2 keyboard port Power connector Voltage selector switch PS2 mouse port Gigabit LAN port (10/100/1000 Mbps)
  • Page 14: Internal Components

    Internal Components Item Component Expansion card Mainboard Optical drive Heat sink fan assembly Power supply Chapter 1...
  • Page 15: System Led Indicators

    System LED Indicators This section describes the different system LED indicators. LED indicator Color Power Green Green — HDD activity Green Green Green/ Amber Amber LAN port Amber network speed Green LED (left) — LAN port Green network connection LED (right) Chapter 1 LED status...
  • Page 16 Chapter 1...
  • Page 17: System Utilities

    System Utilities Phoenix BIOS Setup Utility BIOS setup is a hardware configuration program built into the system's Basic Input/Output System (BIOS). Since most systems are already properly configured and optimized, there is no need to run this utility. You will need to run this utility under the following conditions.
  • Page 18: Entering Bios Setup

    Entering BIOS setup Turn on the server and the monitor. If the server is already turned on, close all open applications, then restart the server. During POST, press Delete. If you fail to press Delete before POST is completed, you will need to restart the server. The Setup Main menu will be displayed showing the Setup’s menu bar.
  • Page 19: Setup Utility Menus

    Setup Utility Menus The tabs on the Setup menu bar correspond to the six primary BIOS Setup menus, namely: Product Information • Standard CMOS Features • Advanced BIOS Features • Advanced Chipset Features • Integrated Peripherals • Power Management Setup •...
  • Page 20: Product Information

    Product Information The Product Information menu displays basic information about the system. These entries are for your reference only and are not user-configurable. Chapter 2...
  • Page 21: Standard Cmos Features

    Standard CMOS Features Parameter Description Date Set the date following the weekday-month-day-year format. Time Set the system time following the hour-minute-second format. Halt On Determines whether the system will stop for an error during the POST. Base Memory Also called conventional memory. Typically, 640 KB will be reserved for the MS-DOS OS. Extended Memory Total size of extended memory detected during POST Total Memory...
  • Page 22: Advanced Bios Features

    Advanced BIOS Features Parameter Description CPU Feature Press Enter to configure the CPU Virtualization and AMD K8 Cool and Quiet Control features. Hard Disk Boot Priority Press Enter to select hard disk boot device priority. Virus Warning Specifies the virus warning feature for IDE hard disk boot sector protection. If enabled, BIOS will show a warning message on the screen or an alarm beep when someone attempts to write data into this area.
  • Page 23 Parameter Description Security Option When set to system, BIOS will ask for the password each time the system boots up. If set to setup, the password is only required for access into the BIOS setup menus. MPS Version Control For Specifies the version of the Multiprocessor Specification (MPS) that the mainboard will use.
  • Page 24 Hard Disk Boot Priority The Hard Disk Boot Priority submenu allows you to specify the sequence of loading the OS from the installed hard drives. Use the up or down arrow key to select a hard drive, then press the <+> key or the <-> key to move it up or down on the list.
  • Page 25: Advanced Chipset Features

    Advanced Chipset Features Parameter Description Hyper SLI Enable or disable the Scalable Link Interface (SLI) technology. iGPU Frame Buffer Control When set to auto, BIOS will automatically setup the frame buffer size. When set to manual, you can set the frame buffer size. Frame buffer size is the total amount of system memory allocated solely for the onboard graphics controller.
  • Page 26 Parameter Description iGPU Spread Spectrum Allows you to set the integrated GPU spread spectrum. SSE/SSE2 Instructions Enables or disables the processor’s SSE and SSE2 instruction sets. MCP78 PCIE Training Cards supporting Gen2 mode will be trained in Gen2 mode. System BIOS cacheable Enables or disables the caching of the mainboard BIOS ROM from F0000h to FFFFFh by the processor’s Level 2 cache.
  • Page 27 DRAM Configuration Parameter Description Timing Mode When set to auto mode, the system reads the electronic data sheet of the memory modules and adjusts the timings accordingly. When set to MaxMemClk, you can manually specify the memory clock frequency independent of the system bus frequency. Memory Clock value or Limit Displays the current memory clock frequency.
  • Page 28: Integrated Peripherals

    Integrated Peripherals Parameter Description IDE Function Setup Press Enter to access the IDE Function Setup submenu. MCP Storage Config Press Enter to access the MCP Storage Config submenu. Init Display First Select whether to boot the system using the AGP graphic card or a PCI card installed on the PCI Express slot or PCI slot.
  • Page 29: Ide Function Setup

    IDE Function Setup Parameter Description OnChip IDE Channel 0 Enables or disables the first IDE channel. Primary Master PIO When set to Auto, BIOS setup automatically detects if the installed hard disk supports the function. If supported, it allows for faster data recovery and read/write timing that reduces hard disk activity time.
  • Page 30 MCP Storage Config Parameter Description SATA Operation Mode Select a SATA operation mode. SATA 0 -- Port 1 ~ 6 Enables or disables the SATA RAID on ports 1 to 6. This parameter can be configured if the SATA Operation Mode is set to RAID SATA SALP Feature Select a Supports Aggressive Link Power Management (SALP) feature.
  • Page 31 USB Device Setting Parameter Description USB 1.0 Controller Enables or disables the onboard USB controller. USB 2.0 Controller USB Operation Mode Select a USB device operation speed. USB Keyboard Function Enables or disables legacy support of the USB keyboard. USB Mouse Function Enables or disables legacy support of the USB mouse.
  • Page 32: Power Management Setup

    Power Management Setup Parameter Description ACPI function Enables or disables the Advanced Configuration and Power Management (ACPI) function. ACPI Suspend Type Select an ACPI state. Power Management Select a power saving method for the following modes: • HDD power down •...
  • Page 33 Power Management Setup (Eup) Parameter Description ACPI function Enables or disables the Advanced Configuration and Power Management (ACPI) function. ACPI Suspend Type Select an ACPI state. Power Management Select a power saving method for the following modes: • HDD power down •...
  • Page 34: Pnp/Pci Configurations

    PnP/PCI Configurations Parameter Description Reset Configuration Data If enabled, the system is forced to update Extended System Configuration Data (ESCD) and then is automatically set to the disabled mode. If disabled, the system ESCD will update only when the new configuration varies from the last one.
  • Page 35: Pc Health Status

    PC Health Status Parameter Description Smart FAN Control Enables or disables the smart system fan control function. Shutdown Temperature Set the CPU shutdown temperature. Chapter 2 Option Enabled Disabled Disabled ° ° 60 C/140 F ° ° 65 C/149 F °...
  • Page 36: Load Default Settings

    Load Default Settings The Load Default Settings menu allows you to load the default settings for all BIOS setup parameters. Setup defaults are quite demanding in terms of resources consumption. If you are using low-speed memory chips or other kinds of low-performance components and you choose to load these settings, the system might not function properly.
  • Page 37: Set Supervisor Password

    Set Supervisor Password The Set Supervisor Password menu allows you to set a supervisor password. The supervisor password allows you to access and change all settings in the Setup Utility. Setting a supervisor password Use the up/down arrow keys to select Set Supervisor Password menu then press Enter. A password box will appear.
  • Page 38: Set User Password

    Set User Password The Set User Password menu allows you to set a user password. Entering this password will restrict a user’s access to the Setup menus. A supervisor password must be set first before you can enable or disable this field.
  • Page 39 Save & Exit Setup The Save & Exit Setup menu allows you to save changes made and close the Setup Utility. Chapter 2...
  • Page 40: Exit Without Saving

    Exit Without Saving The Exit Without Saving menu allows you to discard changes made and close the Setup Utility. Chapter 2...
  • Page 41: System Disassembly

    System Disassembly This chapter contains step-by-step procedures on how to disassemble the desktop computer for maintenance and troubleshooting. Disassembly Requirements To disassemble the computer, you need the following tools: Wrist grounding strap and conductive mat for preventing electrostatic discharge • Flat-blade screwdriver •...
  • Page 42: Pre-Disassembly Procedure

    Pre-disassembly Procedure Before proceeding with the disassembly procedure, perform the steps listed below: Turn off the system and all the peripherals connected to it. Unplug the power cord from the power outlets. Unplug the power cord from the system. Unplug all peripheral cables from the system. Place the system unit on a flat, stable surface.
  • Page 43: Main Unit Disassembly

    Main Unit Disassembly External Modules Disassembly Flowchart The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. MAIN UNIT DISASSEMBLY Screw List Chapter 3 MAIN UNIT SIDE PANEL FRONT BEZEL...
  • Page 44: Removing The Side Panel

    Removing the Side Panel Perform the pre-disassembly procedure described on page 34. Remove the screw (A) located on the rear edge of the side panel. Screw (Quantity) #6-32 L5 BZN (2) Slide the side panel toward the back of the chassis until the tabs on the cover disengage with the slots on the chassis.
  • Page 45: Removing The Font Bezel

    Removing the Font Bezel Remove the side panel. Refer to the previous section for instructions. Release the ffront bezel retention tab from the chassis interior. Pull the bezel away from the chassis. Chapter 3...
  • Page 46: Removing The Heat Sink Fan Assembly

    Removing the Heat Sink Fan Assembly WARNING:The heat sink becomes very hot when the system is on. NEVER touch the heat sink with any metal or with your hands. See “Removing the Side Panel” on page 36. See “Removing the Font Bezel” on page 37. Use a long-nosed screwdriver to loosen the four screws on the heat sink, in the order as shown below.
  • Page 47 Disconnect the fan cable from the mainboard. Lay down the heat sink fan assembly in an upright position—with the thermal patch facing upward. Do not let the thermal patch touch the work surface. Use an alcohol pad to wipe off the thermal grease from both the heat sink and the processor socket retention plate.
  • Page 48: Removing The Processor

    Removing the Processor IMPORTANT:Before removing a processor from the mainboard, make sure to create a backup file of all important data. WARNING:The processor becomes very hot when the system is on. Allow it to cool off first before handling. See “Removing the Side Panel” on page 36. See “Removing the Font Bezel”...
  • Page 49 Pull out the processor from the socket. IMPORTANT:If you are going to install a new processor, note the arrow on the corner to make sure the processor is properly oriented over the socket. Chapter 3...
  • Page 50: Removing The Optical Drive

    Removing the Optical Drive See “Removing the Side Panel” on page 36. See “Removing the Font Bezel” on page 37. See “Removing the Heat Sink Fan Assembly” on page 38. See “Removing the Processor” on page 40. Disconnect the data and power cables from the rear of the optical drive and the mainboard. Release the drive bay retention release lever.
  • Page 51 Pull the lever to the fully open position, as shown below. Pull the drive out of the drive bay. Chapter 3...
  • Page 52: Removing The Hard Disk Drive

    Removing the Hard Disk Drive See “Removing the Side Panel” on page 36. See “Removing the Font Bezel” on page 37. See “Removing the Heat Sink Fan Assembly” on page 38. See “Removing the Processor” on page 40. See “Removing the Optical Drive” on page 42. Remove the HDD-ODD bracket.
  • Page 53 Lift the bracket out of the chassis. Disconnect the data cable from the mainboard. Chapter 3...
  • Page 54 Disconnect the data cable from the rear of the hard drive. Disconnect the power cable from the rear of the hard drive. 10. Place the bracket on a clean, static-free work surface. Chapter 3...
  • Page 55 11. Remove the HDD module. Remove the four screws (B) that secures the HDD module to the HDD bracket. Screw (Quantity) #6-32*3/16 NI (4) Slide the HDD out of the bracket. Chapter 3 Color Torque Silver 5.5 to 6.5 kgf-cm Part No.
  • Page 56: Removing The Power Supply

    Removing the Power Supply See “Removing the Side Panel” on page 36. See “Removing the Font Bezel” on page 37. See “Removing the Heat Sink Fan Assembly” on page 38. See “Removing the Processor” on page 40. See “Removing the Optical Drive” on page 42. See “Removing the Hard Disk Drive”...
  • Page 57 Remove the screw (A) that secures the power supply to the chassis. Screw (Quantity) #6-32 L5 BZN (1) 10. Remove the three screws (A) that secure the power supply to the rear panel. Screw (Quantity) #6-32 L5 BZN (3) Chapter 3 Color Torque Black...
  • Page 58 11. Lift the power supply module out of the chassis. Chapter 3...
  • Page 59: Removing The Memory Modules

    Removing the Memory Modules IMPORTANT:Before removing any DIMM from the memory board, make sure to create a backup file of all important data. See “Removing the Side Panel” on page 36. See “Removing the Font Bezel” on page 37. See “Removing the Heat Sink Fan Assembly” on page 38. See “Removing the Processor”...
  • Page 60 Gently pull the DIMM upward to pull it away from the chassis. Chapter 3...
  • Page 61: Removing The Pci Card

    Removing the PCI Card See “Removing the Side Panel” on page 36. See “Removing the Font Bezel” on page 37. See “Removing the Heat Sink Fan Assembly” on page 38. See “Removing the Processor” on page 40. See “Removing the Optical Drive” on page 42. See “Removing the Hard Disk Drive”...
  • Page 62 Gently pull the card to remove it from the mainboard. Chapter 3...
  • Page 63: Removing The Front I/O And Card Reader Boards

    Removing the Front I/O and Card Reader Boards See “Removing the Side Panel” on page 36. See “Removing the Font Bezel” on page 37. See “Removing the Heat Sink Fan Assembly” on page 38. See “Removing the Processor” on page 40. See “Removing the Optical Drive”...
  • Page 64 Disconnect the other end of the cables from the mainboard. 10. Remove the front I/O and card reader board bracket. Remove the two screws (B) that secures the bracket to the chassis. Screw (Quantity) #6-32*3/16 NI (2) Color Torque Silver 5.5 to 6.5 kgf-cm Part No.
  • Page 65 Push the bracket inward, then remove the bracket from the chassis. 11. Remove the card reader board. Remove the two screws (A) that secure the card reader board to the bracket. Screw (Quantity) #6-32 L5 BZN (2) Chapter 3 Color Torque Black 5.5 to 6.5 kgf-cm...
  • Page 66 Pull the card reader board out of the bracket. 12. Remove the front I/O board. Remove the two screws (A) that secure the I/O board to the bracket. Screw (Quantity) #6-32 L5 BZN (2) Pull the I/O board out of the bracket. Color Torque Black...
  • Page 67: Removing The Mainboard

    Removing the Mainboard See “Removing the Side Panel” on page 36. See “Removing the Font Bezel” on page 37. See “Removing the Heat Sink Fan Assembly” on page 38. See “Removing the Processor” on page 40. See “Removing the Optical Drive” on page 42. See “Removing the Hard Disk Drive”...
  • Page 68 12. Remove the six screws (A) that secures the mainboard to the chassis, in the order shown. Screw (Quantity) Color Torque Part No. #6-32 L5 BZN (6) Black 5.5 to 6.5 kgf-cm 86.00J07.B60 13. Lift the board from the chassis. Chapter 3...
  • Page 69: System Troubleshooting

    This chapter provides instructions on how to troubleshoot system hardware problems. Hardware Diagnostic Procedure IMPORTANT:The diagnostic tests described in this chapter are only intended to test Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses.
  • Page 70: System Check Procedures

    Verify that components are properly seated. Verify that all cable connectors inside the system are firmly and correctly attached to their appropriate connectors. Verify that all components are Acer-qualified and supported. 10. Replace the system covers. 11. Power on the system.
  • Page 71: Post Error And Beep Codes

    POST Error and Beep Codes NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU.
  • Page 72 POST Code (Hex) Use walking 1’s algorithm to check out interface in CMOS circuitry. Also set real- time clock power status, and then check for override. Reserved Program chipset default values into chipset. Chipset default values are MODBINable by OEM customers. Reserved Initial onboard clock generator if Early_Init_Onboard_Generator is defined.
  • Page 73 POST Code (Hex) 1 Initialize double-byte language font (Optional) 2 Put information on screen display, including Award title, CPU type, CPU speed, Reserved Reserved Reserved Reserved Reserved Reset keyboard if Early_Reset_KB is defined e.g. Winbond 977 series Super I/O chips. See also POST 63h. Reserved Test DMA Channel 0 Reserved...
  • Page 74 POST Code (Hex) Reserved Test all memory (clear all extended memory to 0) Clear password according to H/W jumper (Optional) Reserved Display number of processors (multi-processor platform) Reserved 1 Display PnP logo 2 Early ISA PnP initialization Reserved Initialize the combined Trend Anti-Virus code Reserved (Optional Feature) Show message for entering AWDFLASH.EXE from FDD Reserved...
  • Page 75 POST Code (Hex) (Optional Feature) Enter AWDFLASH.EXE if: -AWDFLASH.EXE is found in floppy drive. -ALT+F2 is pressed. Detect serial ports & parallel ports Reserved Reserved Detect & install co-processor Reserved Init HDD write protect Reserved Reserved Switch back to text mode if full screen logo is supported. Reserved Reserved E8POST.ASM starts...
  • Page 76 POST Code (Hex) 1 Enable L2 cache 2 Program Daylight Saving 3 Program boot up speed 4 Chipset final initialization 5 Power management final initialization 6 Clear screen & display summary table 7 Program K6 write allocation 8 Program P6 class write combining Update keyboard LED &...
  • Page 77: Online Support Information

    This section describes online technical support services available to help you repair the desktop computer. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website at http://global.acer.com/ support/index.
  • Page 78 Chapter 4...
  • Page 79: System Block Diagram And Board Layout

    Chapter 5 System Block Diagram and Board Layout System Block Diagram Chapter 5...
  • Page 80: Board Layout

    Board Layout Mainboard Code Description CPUFAN1 Processor fan cable connector PWR2 24-pin ATX power connector DIMM1 and 2 System memory slots Processor socket DEBUGH1 Debug connector SATA2 SATA 2 data cable connector LEDH1 LED cable connector SYSFAN1 System fan cable connector USBF3 Front USB connectors USBF2...
  • Page 81: System Jumpers

    System Jumpers Name Clear CMOS/NVRAM SKU selection Chapter 5 Location Default JBIOS1 GPIOH1 Settings Normal (default) Clear CMOS SSID = 0153 AX1200 SSID = 0157 AX3200...
  • Page 82 Chapter 5...
  • Page 83: Fru (Field Replaceable Unit) List

    To scrap or to return the defective parts, follow the local government ordinance or regulations on • how to dispose it properly, or follow the rules set by your regional Acer office on how to return it. This document will be updated as more information about the FRU list becomes available.
  • Page 84: Aspire X1300/X1301 Exploded Diagram

    Aspire X1300/X1301 Exploded Diagram Chapter 6...
  • Page 85: Aspire X1300/X1301 Fru List

    ASSY DOOR BOXER95 ASSY MAIN-CHASSIS BOXER95 BRKT F-IO BOXER95 SHIELDING REAR IO BOXER95 ASSY BRKT-ODD-HDD IC CPU ATHLON 4850E 2.5G G2 IC CPU ATHLON64*2 4200+ 2.2G IC CPU ATHLON64*2 4400+ 2.3G Acer Description Part Number 55.SAR01.001 55.SAR01.002 FX.10100.003 TU.10500.010 TU.10500.011 VG.PC84L.013...
  • Page 86 IC CPU PHENOM 8700 2.5G IC CPU PHENOM 8750 2.4G IC CPU PHENOM 9500 2.2G IC CPU PHENOM 9550 2.2G IC CPU PHENOM 9600 2.4G IC CPU PHENOM 9650 2.3G IC CPU PHENOM 9750 2.4G Acer Description Part Number KC.A4602.X2Z KC.A4802.X2Z KC.A5002.X2Z KC.A5202.X2Z KC.A5602.X2Z...
  • Page 87 ST3320820AS HDD 320GB HGST HDP725032GLA380 HDD 320GB WD WD3200AAJS- 22VWA0 HDD 500GB SGT SATA ST3500830AS HDD 500GB HGST HDP725050GLA380 HDD 500GB WD WD5000AAJS- 22YFAO HDD 500GB WD5000AAJS-22A8B0 Acer Description Part Number KC.SLE02.125 KC.SLE02.130 KU.0040D.012 KU.01609.005 KU.0160D.034 KU.0160E.001 KV.0040D.001 KV.01609.003 KV.0160D.014 KH.16007.017...
  • Page 88 KB PS2 KB-0759 SPANISH BLACK KB PS2 KB-0759 PORTUGUESE BLAC KB PS2 KB-0759 CA-FRENCH BLACK KB PS2 KB-0759 BRAZILIAN PORTU KB PS2 KB-0759 JAPANESE BLACK KB PS2 KB-0759 GERMAN BLACK Acer Description Part Number KH.64008.001 KH.75001.003 KH.75007.001 KH.75008.001 KH.01K07.001 HI.10800.012 KB.PS203.096 KB.PS203.097...
  • Page 89 KB PS2 KB-0759 SLOVAK BLACK105 KB PS2 KB-0759 RUSSIAN BLACK KB PS2 KB-0759 HUNGARIAN BLACK KB PS2 KB-0759 GREEK BLACK KB PS2 KB-0759 DANISH BLACK105 KB PS2 KB-0759 CZECH BLACK Acer Description Part Number KB.PS203.108 KB.PS203.109 KB.PS203.110 KB.PS203.111 KB.PS203.112 KB.PS203.113 KB.PS203.114...
  • Page 90 KB USB KU-0760 PORTUGUESE BLAC KB USB KU-0760 CA-FRENCH BLACK KB USB KU-0760 BRAZILIAN PORTU KB USB KU-0760 JAPANESE BLACK KB USB KU-0760 GERMAN BLACK KB USB KU-0760 ITALIAN BLACK 1 Acer Description Part Number KB.PS203.126 KB.PS203.127 KB.PS203.128 KB.PS203.129 KB.PS203.130 KB.USB03.062 KB.USB03.063 KB.USB03.064...
  • Page 91 KB USB KU-0760 SLOVAK BLACK KB USB KU-0760 RUSSIAN BLACK KB USB KU-0760 HUNGARIANBLACK KB USB KU-0760 GREEK BLACK KB USB KU-0760 DANISH BLACK KB USB KU-0760 CZECH BLACK KB USB KU-0760 ROMANIAN BLACK Acer Description Part Number KB.USB03.075 KB.USB03.076 KB.USB03.077 KB.USB03.078 KB.USB03.079 KB.USB03.080 KB.USB03.081...
  • Page 92 MOUSE USB OPT MUV_ACR1 931196- SPS 220W NPFC 115V/230V LITEON SPS 220W 115VAC/230V NPFC DPS- SPS 220W PFC 230V DPS-220UB- SPS 220W PFC 230V LITEON PE- SPEAKER USB BLACK 1007011-0G Acer Description Part Number KB.USB03.093 KB.USB03.094 KB.USB03.095 MB.SAR01.001 KN.1GB0H.008 KN.5120M.005 KN.1GB0G.013...
  • Page 93 SCRW PAN M3 L5 BZN SCREW FLAT #6-32*3/16 NI Chapter 6 Part Name SCRW I NO6-32 L5 BZN SCRW PAN #6-32 L6 NI BOXER SCRW PAN M3 L5 BZN SCREW FLAT #6-32*3/16 NI Acer Description Part Number 86.00J07.B60 86.00J44.C60 86.1A324.5R0 86.5A5B6.012...
  • Page 94 Chapter 6...
  • Page 95: Technical Specifications

    Technical Specifications This section provides technical specifications for the system. Processor AMD Athlon Processor Item Specification Type AMD Athlon Model number LE-1600 Frequency (MHz) 2200 L2 cache size (KB) 1024 HyperTransport 2000 (MHz) Socket type Stepping Manufacturing tech 90 nm SOl (CMOS) Wattage (W) System bus (MHz)
  • Page 96 AMD Athlon X2 Dual-Core Processor Item Specification Type AMD Athlon X2 Dual-Core Model number 4850e Frequency (MHz) 2100 L2 cache size (KB) HyperTransport — (MHz) Socket type Stepping Manufacturing tech 65 nm (CMOS) Wattage (W) System bus (MHz) 2000 AMD Phenom X3 Triple-Core Processor Item Specification Type...
  • Page 97 AMD Sempron Processor Item Specification Type AMD Sempron Model number LE-1250 Frequency (MHz) 2200 L2 cache size (KB) HyperTransport (MHz) Socket type Stepping Manufacturing tech 65 nm SOI (CMOS) Wattage (W) System bus (MHz) 1600 System Board Major Chips Item Specification System core logic NVIDIA NForce MCP78 692 BGA...
  • Page 98 System BIOS Item BIOS vendor BIOS version SMBIOS version PCI Interface Item PCI Express controller Number of slots Network Interface Item LAN controller Supports LAN protocol LAN connector type SATA Interface Item SAS controller Connectors Keyboard and Input Devices Item Controller Optical Drive BD-R...
  • Page 99 BD-R Item Write Speed Read Speed Data Transfer Rate Access Time Buffer Size Interface Type Super Multi Item Vendor Model name Drive type Write Speed Specification BD-R(SL) 2x, 4x CLV BD-R(DL)/BD-RE(SL/DL) 2x CLV DVD-R 2x, 4x CLV, 8x ZCLV DVD-R(DL) 2x, 4x CLV DVD-RW 2x, 4x CLV, 6x ZCLV DVD+R 2.4x, 4x CLV, 8x ZCLV DVD+R( DL) 2.4x , 4x CLV...
  • Page 100 Super Multi Item Read Speed Data Transfer Rate Access Time Buffer Size Interface Type DVD-ROM Item Vendor Model name Drive type Write Speed Read Speed Data Transfer Rate Access Time Buffer Size Interface Type Appendix A Specification — — — —...

This manual is also suitable for:

Aspire x1300