Mastervolt ChargeMaster 12/35-3 Installation Manual

Mastervolt ChargeMaster 12/35-3 Installation Manual

Hide thumbs Also See for ChargeMaster 12/35-3:

Advertisement

Installation manual
This Quick installation guide provides a brief overview of a basic ChargeMaster installation.
1
Reading the user's manual is still necessary for safety instructions, additional features, best performance
and years of trouble-free service.
All electrical systems (DC and AC) must be disconnected from any power source during the entire
2
installation! Use isolated tools!
Read the safety instructions (chapter 2 of the user's manual).

Safety regulations and measures

1.
Install the charger according to the instructions in both the user's and installation manual.
2.
Never use chargers at a location where there is danger of gas or dust explosions.
3.
Connections and safety features must be executed according to locally applicable regulations.
Mastervolt cannot be held liable for:
Damage resulting from the use of the battery charger;
Possible errors in the included manual and the consequences of these;
Use that is inconsistent with the purpose of the product.

Check the contents of the delivery.

3
Check from the identification label if the
4
battery voltage and current matches the
DC output of the ChargeMaster.
Choose the right DC wiring and fuses,
see the table below for recommended
values.
Part no
ChargeMaster 1
model
44010350
12/35-3
44010500
12/50-3
44020200
24/20-3
44020300
24/30-3
ChargeMaster 1
DC Cable cross
DC Cable cross
section <2m/ 6ft
section 2-5m/16ft
16mm² / 4AWG
25mm² / 2AWG
25mm² / 2AWG
35mm² / 1AWG
10mm² / 6AWG
16mm² / 4AWG
16mm² / 4AWG
25mm² / 2AWG
AC mains cable
(2m, attached
already)
Contact your supplier if one of the items is missing.
Do not use the ChargeMaster if it is damaged.
Part no : 44020300
Type
Input
Output : 28.5VDC- 30A
Serial no: V822A0001
DC
fuse
40A
63A
32A
40A
MasterBus
terminator
Battery
temperature
sensor
: ChargeMaster 24/30-3
: 120/230V AC 50/60 Hz 8.5A/4.2A
Made in PRC
Minimum battery
capacity
70-350Ah
100-500Ah
50-250Ah
70-350Ah
IP 23
Design by
Mastervolt

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ChargeMaster 12/35-3 and is the answer not in the manual?

Questions and answers

Summary of Contents for Mastervolt ChargeMaster 12/35-3

  • Page 1 Never use chargers at a location where there is danger of gas or dust explosions. Connections and safety features must be executed according to locally applicable regulations. Mastervolt cannot be held liable for: • Damage resulting from the use of the battery charger;...
  • Page 2 Installation manual ChargeMaster 1 Mount the ChargeMaster 1 to the wall. Two ways are possible. Mounting the bracket to Mounting the bracket to the the wall and fixing the ChargeMaster and hanging ChargeMaster onto it. the ChargeMaster onto the wall. Use the dimensions on the back of this manual.
  • Page 3 Installation manual ChargeMaster 1 Battery fuse MasterBus terminator MasterBus cable Battery temperature sensor Step 4 shows wire cross sections and fuse ratings. Change the Dipswitch settings if necessary. Switch 1 Switch 2 Wet battery 3step+ charging AGM, Gel, Spiral battery Constant voltage charging (Float = 13.25/26.5V) See user’s manual section 5.1 for Dip switch 3 and 4 settings.
  • Page 4 Installation manual ChargeMaster 1 Model 12/35-3 12/50-3 24/20-3 24/30-3 Nominal input voltage: 120/230V 120/230V 120/230V 120/230V Nominal input 50/60Hz 50/60Hz 50/60Hz 50/60Hz frequency: Full load consumption: 575VA 825VA 660VA 925VA Nominal output voltage: Total maximum charge 35A at 14.4V 50A at 14.4V 20A at 28.8V 30A at 28.8V current:...

Table of Contents