Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
ALI-NVR71128R Embedded Network Video Recorder Setup Guide
This setup guide provides instructions to initially setup and use the ALI-NVR71128R network video recorder (NVR). This NVR features:
Supports up to 128 video input (camera) channels
•
Pluggable HDD provides a convenient HDD installation and maintenance; low-noise design
•
Supports HDD hot-swap with RAID0, RAID1, RAID5, RAID6, and RAID10 storage scheme with configurable N+1 hot spare
•
Up to 24 SATA hard disks can be connected for recording and backup
•
Redundant hot-swap power supply to improve the system stability
•
Dual-OS design to ensure the reliability of system
•
Connectable to ALIBI IP cameras and third-party network cameras including ACTI, ALIBI, Arecont, AXIS, Bosch, Brickcom, Canon,
•
HILVISION, PANASONIC, Pelco, PSIA, SAMSUNG, SANYO, SONY, Vivotek, ZAVIO and other ONVIF compatible cameras
Support live view, storage, and playback of the connected camera with up to 12 megapixels resolutions
•
Simultaneous HDMI 1 / VGA (main) and HDMI 2 (auxiliary) outputs
•
Video outputs at up to 4K (4096 × 2160) resolution
•
Video Wall display options with 6 display channels
•
Supports decoding up to 20 channels at 1080p resolution
•
4 self-adaptive 10M/100M/1000M network interfaces, 4 1.25 Gbps SFP optical channels
•
VCA detection alarm is supported including search for face detection, behavior analysis, people counting and heat map
•
For information about using your NVR and its extensive capabilities, refer to the following documents provided by your equipment vendor or
at: www.alibisecurity.com/resources.
ALIBI™ Tools Utility Installation and User Manual
•
ALIBI™ Witness 2.0 Smartphone App User Guide
•
Alibi Central Management System (ACMS) Version 3.1 User Manual
•
NVR Controls, connectors and indicators
Front Panel
Power, Status USB panel
Handle (2)
Front panel key lock
Touch-display control panel
1
www.Observint.com
Front panel module
HDD bay occupancy indicators
Power, Status, USB panel
Name
Function Description
POWER button
Press to power on /off the NVR.
Solid blue indicates NVR is powered on.
POWER
Solid red indicates NVR is powered off.
- Solid red: at least one HDD is installed
HDD
- Not lit: No HDD is detected
- Blinking red: HDD is reading or writing
Status Indicators
TX/RX
Flashes blue when network communication is normal. .
READY
Ready LED is normally blue, indicating that the device is functioning properly.
ALARM
Solid red indicates an alarm condition is present.
USB connector
USB 3.0 port
HDD bay occupancy indicators (1..24)
Lit when an HDD occupies the bay
Front Panel Lock
You can lock (or unlock) the panel by the key to remove the front panel for access to HDD bays
Touch-display control panel
Provides firmware displays with touch controls
Front with front panel removed
HDD bay 1
HDD bay 21
HDD Bay occupancy indicators
HDD bay 4
HDD bay 24
ALI-NVR71128R_SQ
170808
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ALIBI ALI-NVR71128R
Summary of Contents for ALIBI ALI-NVR71128R
- Page 1 ALI-NVR71128R Embedded Network Video Recorder Setup Guide This setup guide provides instructions to initially setup and use the ALI-NVR71128R network video recorder (NVR). This NVR features: Supports up to 128 video input (camera) channels • Pluggable HDD provides a convenient HDD installation and maintenance; low-noise design •...
-
Page 2: Back Panel
Back Panel HDMI Video Out (4K) Extension board Power supply modules (2) Aux HDMI Video Input HDMI Video Out (1080p) Decoding board module faceplate (slot 2) 1.25 Gbps SFP optical (fiber) channels (4) Alarm In (32) / Out (16) RS-485 (8) terminals (see below) Fan module Decoding board Controller module... - Page 3 d Output wiring General guidelines for installing your system RM INPUT AN Up to 48 alarm inputs and up to 24 alarm outputs can be connected to the NVR. Terminations for these devices are located on two modules: What you need Controller module: Terminations provided for alarm inputs 1 ..
-
Page 4: Step 1. Nvr Installation
Secure the NVR to the rack with the two bolts (not provided), one through the upper left corner and one through the upper configuration can be setup during system initialization and with Alibi CMS V3.1 (or later). right corner of the front. -
Page 5: Mouse Control
iii. Lay the tray on a flat surface. Place the HDD in the tray with the connectors toward the back as shown in the picture below, and then secure the HDD to the tray with four screws, two on each side. Connectors Lock Handle... -
Page 6: Step 2. Using The Wizard For Basic Configuration Setup
Lowercase Switch to Enter Power on the NVR using the POWER button on the front panel. Normally, an Alibi logo splash screen appears on the system Main numeric monitor and the NVR front panel display within about 2 minutes. Soft keyboard - alphanumeric Power on the monitor(s). - Page 7 By default, the Setup Wizard will open automatically. Refer to the Alibi Embedded Network Video Recorder Firmware V3.6.x User In the next screen, set the time zone and date format (using the drop down menus), and the date and time in your recorder (using the Manual for incomplete instructions for using the Wizard and configuring and using your NVR.
- Page 8 In the window shown below, you can check the select box to enable RAID for the HDDs storage in the NVR. By default in the Wizard, RAID 5 is used. To enable fixed network settings, first, un-check the Enable DHCP box. If a DHCP server is active on your network, the IPv4 Address, IPv4 Subnet Mask, IPv4 Default Gateway fields will be populated with network settings assigned by the server.
-
Page 9: Access The Menu System
In the next window, click Search button to discover all compatible cameras on the LAN(s) the NVR is attached to. Other devices, such as NVRs and Alibi compatible storage servers are also listed. You can add cameras to the NVR in two ways: After selecting the recording mode, click OK, and then click Yes in the Attention popup window. -
Page 10: Specifications
Power Consumption ≤ 140 W (without HDDs) For additional information about using your system, refer to the ALIBI Embedded Network Video Recorder Firmware V3.6.x User Working temperature 32 °F to 122 °F (0 °C to + 50 °C) Manual available from by your vendor.
Need help?
Do you have a question about the ALI-NVR71128R and is the answer not in the manual?
Questions and answers