Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Hayward MakoShark 2
Summary of Contents for Hayward MakoShark 2
- Page 1 ISRC9403 Rev B...
- Page 2 KingShark2...
-
Page 3: Limited Warranty
Any repair that is made on your cleaner during the warranty period by anyone other than an Authorized Hayward Warranty Service Center (designated to perform such work) will void this warranty and other warranty rights you may have. -
Page 4: Table Of Contents
KingShark2 CONTENTS Safety Precautions ..............2 General Information ...............3 Motor Information ..............4 Trouble Shooting ..............5 Specifications ................7 Machine Assembly/Parts ............8 Filter Assembly/Parts ............10 Accessories .................11 Preventive Maintenance ............13 Parts Ordering Instructions ..........14 Rev. 3/10... -
Page 5: Safety Precautions
KingShark2 SAFETY PRECAUTIONS The KingShark2 automatic swimming pool vacuum cleaner has been manufactured with the highest degree of care and concern for safety. We suggest the following safety precautions become part of your pool safety regulations: ALWAYS PUT THE MACHINE INTO THE WATER BEFORE CON- NECTING IT TO THE ELECTRICAL OUTLET. -
Page 6: General Information
KingShark2 GENERAL INFORMATION You have purchased the finest piece of equipment in the pool cleaner industry. If you treat it as such, your KingShark2 automatic swimming pool vacuum cleaner will give you years of satisfactory service. As a suggestion, the unit should be stored in the original shipping container for safekeeping during the off season. -
Page 7: Motor Information
KingShark2 REMOVE THE UNIT IMMEDIATELY AFTER USE. ALLOWING UNIT TO COOL IN WATER AFTER RUNNING CAN CAUSE MOTOR SEAL DAMAGE. To clean the cartridge filters #7807 (Page 10, Key 7) remove the filter housing assembly #3400 (Page 10, Key 13) by removing the filter knob and releasing the filter box. -
Page 8: Trouble Shooting
KingShark2 TROUBLE SHOOTING Where to set Sensor Bar (Make adjustments in 1/4" Increments) Machine fails to come out of deep end: Raise sensor bar to allow the machine to climb the incline to shallow end. Machine turns in circles and twists cord: Sensor bar too high, hitting hood, or is not level. - Page 9 KingShark2 TROUBLE SHOOTING Unit runs for short distance but stops. Check for overloaded circuit or possible faulty motor. *Contact service center* (DO NOT USE EXTENSION CORDS.) Motor runs but unit becomes motionless (gear box worm is worn or the drive pin is sheared). Machine tips over backwards before sensing wall: Improper sensor bar adjustment, (too high).
-
Page 10: Specifications
KingShark2 SPECIFICATIONS MOTOR: Type ..............Submersible EXPORT ONLY Voltage ..............110/115 Volts ........ 230/240 Volts Frequency ............. 60 Cycle ...........60/50 Cycle Speed ..............1725 RPM ..........1425 RPM Bearing ..............Ball Bearings Housing ..............Aluminum Anodized Motor Seals ............Double Lip Wave Overload Protection .......... -
Page 11: Machine Assembly/Parts
KingShark2 WITH SWIVEL... - Page 12 KingShark2...
-
Page 13: Filter Assembly/Parts
KingShark2 HOOD & FILTER ASSEMBLY PART NO. PART DESCRIPTION 3310G HOOD - GREY PLASTIC 3310GS SWIVEL HOOD - GREY PLASTIC 3309 SPACER - HOOD MOUNTING 212B BOLT HEX HD 1/4-20X3/4" SS 3405 KNOB - FILTER 3409 KNOB - FILTER ASSEMBLY 3401 INTAKE - FILTER HOUSING 3402... -
Page 14: Accessories
KingShark2 ACCESSORIES... - Page 15 KingShark2 ACCESSORIES CADDY CART...
-
Page 16: Preventive Maintenance
KingShark2 KingShark2 PREVENTATIVE MAINTENANCE Congratulations on the purchase of the KingShark2. The KingShark2 is built and designed to give you years of service. In order to maximize efficiency and receive long term service, we suggest the following: Thoroughly rinse entire unit after use. Clean filters thoroughly after each use - a clogged filter will decrease efficiency dramatically. -
Page 17: Parts Ordering Instructions
KingShark2 serial number and the date of purchase. If you need the location of your nearest Service Center, go to the Haywardnet.com or call Hayward, 908-351-5400 All parts will be shipped immediately via best way on a collect freight basis, from the Service Center. - Page 18 The MakoShark 2 and TigerShark are portable automatic vacuum cleaners. THERE IS NO INSTALLATION! Several hours each week will enable the MakoShark 2 and TigerShark to keep your pool spotless. NO WHIPS, NO PIPES OR EXTRA PLUMBING. Remember, when you really clean your home, you don't just sweep or dust, you vacuum.
- Page 19 KingShark2...
- Page 20 Mail today to Place Stamp Here HAYWARD POOL PRODUCTS Attn: Warranty Department 620 Division Street Elizabeth , NJ 07207 FOLD and MAIL Serial #_____________________________ KingShark2 (Located on the Unit and Shipping Carton) Registration of Guarantee Name ___________________________________________________________________ Address _________________________________________________________________ City ______________________ State __________ Zip__________________________...
Need help?
Do you have a question about the MakoShark 2 and is the answer not in the manual?
Questions and answers