Security - McCulloch ROB R600 Operator's Manual

Park the robotic lawnmower in the charging station and
Test OUT - Remote start 1 . The robotic
select
lawnmower will then leave the charging station straight
away along the guide wire and begin mowing after the
designated distance.
How to measure the distance from the charging station
to a remote area:
Enter a distance which beyond any doubt exceeds the
real figure. The maximum distance that can be entered
is 100 m / 328 ft. Park the robotic lawnmower in the
charging station and select Test OUT . The robotic
lawnmower will immediately leave the charging station.
The distance, stated in metres, will be shown in the
mower display as the robotic lawnmower operates. Stop
the robotic lawnmower at the required position and note
the distance. Enter the displayed number of metres in
the Distance field for the working area in question.
Remote start 2 has been activated, i.e. if another
If
option other than Never has been selected for
Proportion , these settings must also be tested. Remote
start 2 test is performed in the same way as for Remote
start 1 .
3.14.3.2 Test IN
The Test IN function allows you to test how well the
robotic lawnmower docks with the charging station.
Test IN can only be performed after Test OUT has
Note:
been performed.
Selecting this function causes the robotic lawnmower to
travel directly along the guide wire towards the charging
station and to dock with it. The test is approved only if
the robotic lawnmower is able to dock with the charging
station at the first attempt. If the robotic lawnmower is
unable to dock on the first attempt, it will automatically
try again. The installation is not approved if the robotic
lawnmower needs two or more attempts to dock with the
charging station.
3.14.4 Drive past wire
The front of the robotic lawnmower always passes the
boundary wire by a specific distance before the mower
turns around. The default distance is 25 cm / 10 in. but
this can be changed if required. The minimum value is
20 cm / 8 in., and the maximum value is 30 cm / 12 in.
Note that the distance given is only an approximate
value. In reality, the actual distance the robotic mower
passes the boundary wire can vary.
Specify the number of centimetres you want the robotic
lawnmower to pass the boundary wire and press

3.15 Security

Through this selection, settings relating to security and
the connection between the mower and the charging
station can be made.
358 - 002 -
3.15.1 Change PIN code
Enter the new PIN code and press
code again and confirm by pressing
code is changed, the message
appears in the display.
Make a note of the new PIN code on the designated line
MEMO . See Introduction on page 3
on the
3.15.2 Security level
There are 3 security levels to choose from.
Security level
Low and Medium security prohibits access to the robotic
lawnmower if the PIN code is unknown.
also includes a warning that beeps if the correct PIN
code is not entered after a designated time period.
If the wrong PIN code is entered 5 times in succession
the robotic lawnmower is blocked for a time. The
blockage time is extended for every new incorrect
attempt.
Function
Time lock
PIN request
Alarm
3.15.2.1 Time lock
This function means that the robotic lawnmower cannot
be started after 30 days without first entering the correct
PIN code. When the 30 days has passed the robotic
lawnmower will continue to mow as normal, but the
Enter PIN code message appears when the hatch is
opened. Enter your code again and press
OK .
3.15.2.2 PIN request
This function means that the robotic lawnmower
requests a PIN code when the main switch is set to
and each time the hatch is opened. The correct PIN
code must be entered to use the robotic lawnmower.
If the wrong PIN code is entered 5 times in succession
the robotic lawnmower is blocked for a time. The
blockage time is extended for every new incorrect
attempt.
SECURITY
Change PIN code
Security level
New loop signal
OK . Enter the same
OK . When the PIN
PIN code changed
Low
Medium
High
High security
Low Medium
X X
X
OK .
Installation - 25
High
X
X
X
1