Download Print this page
Dexter Laundry T-30 Operator's Manual

Dexter Laundry T-30 Operator's Manual

Commercial dryer vended c-series control, electrc-heated for gb & ie

Advertisement

Quick Links

COMMERCIAL DRYER
MODEL T-30, T-50, & T-80 VENDED
C-SERIES CONTROL, ELECTRC-HEATED
The dryer will operate correctly in ambient temperatures of +5°C to +45°C, in relative humidity up to
50% at +40°C and above 50% when below +40°C, and at altitudes up to 1000m above sea level,
must be transported and stored from -40°C to +140°C, and has been packaged to prevent damage
from humidity, vibration, and shock. Take measures to avoid harmful effects of occasional
condensation.
Post the following "For Your Safety" caution in a prominent location:
Do not store or use petrol or other flammable vapours and liquids or dry cleaning solvents in the
vicinity of this or any other appliance.
THIS MACHINE IS FOR DRYING ONLY FABRICS WASHED IN WATER.
To avoid possibility of fire, including spontaneous combustion, do not dry oiled floor mops, items
containing foam rubber or similarly textured rubberlike materials or any material on which you have
used a cleaning solvent or which contains flammable liquids or solids (such as petrol, kerosene, waxes,
etc.) Fabric softeners, or similar products, should be used per the fabric softener instructions. Remove
all objects from pockets such as lighters and matches.
WARNING – Risk of Fire
Clothes dryer installation must be performed by a qualified installer.
Install the clothes dryer according to the manufacturer's instructions and local codes.
Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is
installed, use duct that has been investigated and found acceptable for use with clothes dryers.
Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will
obstruct clothes dryer airflow and increase the risk of fire.
To reduce the risk of severe injury or death, follow all installation instructions.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision. Children of less than 3 years should be kept away
unless continuously supervised.
It is important that you read this Manual and retain it for future reference. For service or
replacement parts, contact the distributor in your area or the manufacturer:
8514-250-001 REV D PAGE 1
OPERATOR'S MANUAL
INSTALLATION & OPERATION INSTRUCTIONS
FOR YOUR SAFETY
FOR YOUR SAFETY
Dexter Laundry, Inc.
2211 West Grimes Avenue
Fairfield, Iowa 52556, USA
Original Instructions
For GB & IE

Advertisement

loading

Summary of Contents for Dexter Laundry T-30

  • Page 1 COMMERCIAL DRYER Original Instructions MODEL T-30, T-50, & T-80 VENDED For GB & IE C-SERIES CONTROL, ELECTRC-HEATED OPERATOR’S MANUAL INSTALLATION & OPERATION INSTRUCTIONS The dryer will operate correctly in ambient temperatures of +5°C to +45°C, in relative humidity up to 50% at +40°C and above 50% when below +40°C, and at altitudes up to 1000m above sea level,...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Page No. Warnings about use and operation Dryer Specifications 4 - 6 Dryer Dimensions 7 – 15 Installation Instructions 16 – 20 Dryer Shutdown Operating Instructions Programming the Dryer Control 22 - 30 Servicing and Troubleshooting Preventative Maintenance Instructions WARNINGS ABOUT USE AND OPERATION Caution! There are sharp edges on various sheet metal parts internal to the enclosure.
  • Page 3 WARNINGS ABOUT USE AND OPERATION continued THIS DRYER IS EQUIPPED WITH A MANUALLY RESETTABLE OVER-TEMPERATURE THERMOSTAT located to the right of the motor on the rear of the cabinet. Should the dryer cease to heat, refer to your “Service Procedure and Parts Data” book for instructions. CHECK THIS THERMOSTAT WHEN INSTALLING DRYER to assure it is not tripped.
  • Page 4: Specifications

    SPECIFICATIONS 30 lb. Commercial Dryer: T-30 – DC0030E_-79_C_X (50 Hz) Cabinet Height 72 1/4” 1835 mm. (Assumes minimum leveling leg adjustment) Cabinet Width 31 1/2” 800 mm. Overall Depth 43 3/4” 1111 mm. Floor to Bottom of Door 28 3/4”...
  • Page 5 50 lb. Commercial Dryer: T-50 – DC0050E_-79_C_X (50 Hz) Cabinet Height 72 1/4” 1835 mm. (Assumes minimum leveling leg adjustment) Cabinet Width 34 1/2” 875 mm. Overall Depth 50” 1270 mm. Floor to Bottom of Door 27 1/4” 692 mm. Door Opening 25 5/8”...
  • Page 6: Dryer Dimensions

    Electrical Service L1 + L2 + L3 + N + PE Shipping Weight 729 lbs. 331 kg. Net Weight 699 lbs. 291 kg. Clearance Behind Machines (min.) 18” 457 mm. T-30 DRYER DIMENSIONS- FRONT VIEW 8514-250-001 REV D PAGE 6...
  • Page 7 8514-250-001 REV D PAGE 7...
  • Page 8 T-30 DRYER DIMENSIONS- SIDE VIEW 8514-250-001 REV D PAGE 8...
  • Page 9 T-30 DRYER DIMENSIONS- TOP VIEW 8514-250-001 REV D PAGE 9...
  • Page 10 T-50 DRYER DIMENSIONS- FRONT VIEW 8514-250-001 REV D PAGE 10...
  • Page 11 T-50 DRYER DIMENSIONS- SIDE VIEW 8514-250-001 REV D PAGE 11...
  • Page 12 T-50 DRYER DIMENSIONS- TOP VIEW 8514-250-001 REV D PAGE 12...
  • Page 13 T-80 DRYER DIMENSIONS- FRONT VIEW 8514-250-001 REV D PAGE 13...
  • Page 14 T-80 DRYER DIMENSIONS- SIDE VIEW 8514-250-001 REV D PAGE 14...
  • Page 15: Dryer Dimensions

    T-80 DRYER DIMENSIONS- TOP VIEW 8514-250-001 REV D PAGE 15...
  • Page 16: Installation Instructions

    INSTALLATION INSTRUCTIONS Note: A forklift, or a hand pallet truck or jack, must lift the dryer and only from the front or rear of the dryer with the dryer bolted to the pallet and supported the full length of the dryer. UNCRATING AND PLACING THE DRYER Tools Required: 3/4"...
  • Page 17 Do not obstruct the flow of combustion and ventilation air. Maintain minimum of 25 mm (1 in.) clearance between duct and combustible material. Refer to installation label attached to rear guard for other installation information. VERTICAL CLEARANCE DIMENSIONS - ALL DC0030/0050/0080 3.
  • Page 18 necessary that the dryer be connected to a good earth connection. The earth connection resistance should be checked prior to operation. Introduction of supply wiring must not increase the Ingress Protection (IP) rating. HEATING ELEMENT SUPPLY VOLTAGE MINIMUM DUAL ELEMENT MINIMUM WIRE SIZE FROM FUSED SIZE (kW) TIME DELAY FUSE SIZE AT...
  • Page 19 recommend the installation of transient voltage surge suppressors for your new equipment. These devices may be placed at the power supply panel for the complete installation and don’t require an individual device for each machine. These surge protectors help to protect equipment from large spikes and also from small ongoing spikes in the power that occur on a day to day basis.
  • Page 20: Dryer Shutdown

    Installation of several dryers, where a main discharge duct is necessary, will need the following considerations for installation (see Figure 2). Individual ducts from the dryers into the main discharge duct should be at a 45-degree angle in the direction of discharge airflow. NOTE: Never install the individual ducts at a right angle into the main discharge duct.
  • Page 21: Operating Instructions

    OPERATING INSTRUCTIONS Maximum Load Capacity: 13.6 kg (30 Pounds) Dry Weight for DC0030 Maximum Load Capacity: 22.7 kg (50 Pounds) Dry Weight for DC0050 Maximum Load Capacity: 36.4 kg (80 Pounds) Dry Weight for DC0080 STARTING THE DRYER 1. The display on the dryer control will show the required vend amount when in idle mode. Once the door is opened it will prompt the user to add money.
  • Page 22: Programming The Dryer Control

    PROGRAMMING THE DRYER CONTROL The dryer control can be programmed to prompt the user for alternate vend prices, change dryer cycle times, temperatures and many other options. This can be accomplished in two ways: 1. Manual programming utilizing the “Start”, “High”, “Medium” and “Low” buttons. 2.
  • Page 23 These alternate functions allow the user to move through a menu of options to choose various programmable settings. The figure below shows the top level menu. Choosing an option from the top level menu will then display the next level of options (the sub menu). Quick Test Option: When the Quick Test Option is chosen, the dryer will begin a shortened dry cycle without the displayed vend price being met.
  • Page 24 3. “TIME SET VEND” is the cycle time that the customer has available once they’ve met the Base Vend Price. 4. “FREE SET TIME” is the cycle time that the customer has available if the Base Vend Price is set to “FREE”. 5.
  • Page 25 Cycles Option: This option allows the user to set temperature and cooldown information for the drying cycle. It also allows the user to return the values to factory defaults. 1. “TEMP SETTINGS” allows the user to make adjustments, within a designated range, to the cycling temperature for each of the “Low”, “Medium”...
  • Page 26 Temperature Pricing Option: This option allows the user to require additional vend amounts be added based on the drying temperature chosen by the customer. This pricing adder is effective only for the Base Vend Price (it does not affect the Extend Dry Price). It allows a pricing adder separate for “Medium” and “Hot” temperature settings. Example- A store owner has programmed the control for the following: Vend Price $1.00...
  • Page 27 7. “Shift Hours”: This feature allows the user to shift the time used by the control from the time kept internally by the control. The control uses a Real Time Clock (RTC) to internally track the time and date. The RTC continues operation even if the control loses external power. The RTC is set for Central Standard Time and no daylight savings.
  • Page 28 The figure below shows the sub menu options for Settings: 8514-250-001 REV D PAGE 28...
  • Page 29 Usage Menu: The Usage menu allows for the user to track data about machine usage. See below for detailed information on each sub menu option. 1. “Coin Audit”: The coin audit field shows the accumulation of coin pulses that were sent to the control over each of the left and right coin inputs.
  • Page 30 Control Menu: The Control menu allows for the user to observe important technical information for the control. No changes can be made at this menu. See below for detailed information on each sub menu. 1. “Serial Number”: This is the control serial number. 2.
  • Page 31: Servicing And Troubleshooting

    SERVICING AND TROUBLESHOOTING CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. If any of the following symptoms occur on this dryer, check the suggested remedies listed below. If all probable causes have been eliminated and the symptom still exists, contact your local Dexter agent for further troubleshooting assistance.
  • Page 32 8533-088-001 8533-088-001 8533-088-001 For service and parts information, contact your local Dexter agent. If a Dexter agent is not available, contact Dexter Laundry, Inc. directly as listed below: Mailing Address: 2211 West Grimes Avenue Phone: 1-800-524-2954 Fairfield, IA 52556 USA Website: www.dexter.com/...
  • Page 33 DOW CORNING -- MOLYKOTE BR2-S GREASE -- 9150-00K000170 ================== Product Identification ===================== Product ID: MOLYKOTE BR2-S GREASE MSDS Date: 01/01/1985 FSC: 9150 NIIN: 00K000170 MSDS Number: BBZNK ==================== Responsible Party ===================== Company Name: DOW CORNING Emergency Phone Number: 517-496-5900 CAGE: 5D028 ================== Contractor Identification =================== Company Name: DOW CORNING CORP Address: 3901 S SAGINAW RD Box: 997...
  • Page 34 Machinery Directive on machinery safety, 2006/42/EC Conforming Commercial Drying System Machinery: Model Numbers: DC30X2E, DC0030E, DC0050E, DC0080E, DCS030E Serial Numbers: Manufacturer: Dexter Laundry, Inc. 2211 West Grimes Avenue Fairfield, IA 52556 USA Harmonised EN ISO 12100:2010 Safety of machinery. General principles for Standards design.
  • Page 35 WITH COUNCIL DIRECTIVE 2004/108/EC Directive: Electromagnetic Compatibility Directive 2004/108/EC Conforming Commercial Drying System Machinery: Model Numbers: DC30X2E, DC0030E, DC0050E, DC0080E, DCS030E Manufacturer: Dexter Laundry, Inc. 2211 West Grimes Avenue Fairfield, IA 52556 USA Harmonised EN 55014-1:2006/A2:2011 Electromagnetic compatibility. Requirements Standards CISPR 14-1:2005/A2:2011...
  • Page 36 Declaration of Noise Emission The Dexter Laundry Commercial Drying System Models Sound Pressure Levels per EN ISO 11202 as measured on similarly constructed models are as follows: Model DCBD30KC-64FN Operating Idle (Operator Position) 61 dB (A) 54 dB (A) (Bystander Position)

This manual is also suitable for:

T-50T-80