Advertisement

Quick Links

MODEL: HE
OPERATING INSTRUCTION
AND PARTS MANUAL
I HE-2010
I HE-3010
I
I
I
SHARK PRESSURE WASHERS
4275 N.W. Pacific Rim Blvd.
Camas, WA 98607
USA
For technical assistance or the Shark Dealer nearest you, call 1-800-771-1881.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HE-3010 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Shark Pressure Washers HE-3010

  • Page 1 MODEL: HE OPERATING INSTRUCTION AND PARTS MANUAL I HE-2010 I HE-3010 SHARK PRESSURE WASHERS 4275 N.W. Pacific Rim Blvd. Camas, WA 98607 For technical assistance or the Shark Dealer nearest you, call 1-800-771-1881.
  • Page 3 G G G G G Pump Volume At Pump Head: Total Machine Amperage: HE-2010 2.0 GPM HE-2010 15 Amps HE-3010 2.8 GPM HE-3010 20 Amps G G G G G G G G G G Pump Pressure At Pump Head:...
  • Page 4: Table Of Contents

    CONTENTS Introduction............. 5 Exploded View ............10 Important Safety Information ....... 5-6 Exploded View, Parts List ........11 Pre-Operation Checklist .......... 5 Hose & Spray Gun Assembly ....... 12 Set-Up Procedures ..........6 Downstream Injector Assembly ......13 Operating Instructions ..........6 Troubleshooting ............
  • Page 5: Introduction

    RISK OF EXPLOSION: an explosive location. Operate DO NOT SPRAY Shark Pressure Washers reserves the right to make only where open flame or torch FLAMMABLE LIQUIDS. changes at any time without incurring any obligation. is permitted.
  • Page 6: Setup Procedures

    HE SERIES PRESSURE WASHER OPERATOR’S MANUAL 8. Machines with spray gun should not be operated with 4. Attach connector on discharge hose to spray gun the trigger in the off position for extensive periods of using teflon tape on threads. time as this may cause damage to the pump.
  • Page 7: Component Identification

    HE SERIES PRESSURE WASHER OPERATOR’S MANUAL COMPONENT IDENTIFICATION Plug (120V) Power Electric Supply Motor Oil Dip GFCI Stick Water Faucet Detergent Bucket (not included) Discharge Nipple Detergent Injector Quick Coupler Water Supply Inlet Hose Connector (not included) Detergent Pick-up Tube Wand Wand Spray...
  • Page 8: General Washing Techniques

    HE SERIES PRESSURE WASHER OPERATOR’S MANUAL GENERAL WASHING TECHNIQUES Hold spray nozzle approximately one foot from the sur- face being cleaned. Spray at an angle to get under the material and lift it off. Quick Coupler Wand Spray Nozzle 1 Foot When washing large objects, use detergent injector to apply detergent (see section “How to Use the Detergent Injector”).
  • Page 9: How To Use The Detergent Injector

    HE SERIES PRESSURE WASHER OPERATOR’S MANUAL 5. Install the brass soap nozzle provided with the in- HOW TO USE THE jector into the quick coupler of the wand. DETERGENT INJECTOR 6. Open trigger spray gun. Water detergent ratio is ap- proximately 15 to 1.
  • Page 10: Exploded View

    HE SERIES PRESSURE WASHER OPERATOR’S MANUAL EXPLODED VIEW HE 3010 Models Only Rear View 2010 Models Only SHARK HE • Rev 7/02...
  • Page 11: Exploded View Parts List

    HE SERIES PRESSURE WASHER OPERATOR’S MANUAL EXPLODED VIEW PARTS LIST ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION 5-1046 Motor, 1.5 HP, 1 PH, 3450 RPM, 2-10942 Swivel, 1/2 MP x 3/4" GHF C-Face (201001D, 201007D) w/Strainer (201007D, 301007D) 1 5-1047 Motor, 2 HP, 1 PH, 3450 RPM, 95-07200126...
  • Page 12: Hose & Spray Gun Assembly

    HE SERIES PRESSURE WASHER OPERATOR’S MANUAL HOSE & SPRAY GUN ASSEMBLY Pressure Nozzle Brass Soap Nozzle ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 2-2002 Coupler, 3/8" Female 2-2000 Coupler, 1/4" Female L Quick Coupler O-Ring, Large, L Quick Coupler O-Ring, Small, 2-0121 2-0119 3/8"...
  • Page 13: Downstream Injector Assembly

    HE SERIES PRESSURE WASHER OPERATOR’S MANUAL DOWNSTREAM INJECTOR ASSEMBLY 4-011183 • 2010 • 3010 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 3-1202 Injector, Detergent, Non-Adj., 2-9000 Clamp, Screw, #4 2-3 GPM, .070 4-02080000 Tube, 1/4" x 1/2", Clear Vinyl /ft. 6 2-1904 Strainer, 1/4", Hose Barb SHARK HE •...
  • Page 14: Troubleshooting

    HE SERIES PRESSURE WASHER OPERATOR’S MANUAL TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Pump sucking air Check water supply and possibility of air seepage. PUMP RUNNING NORMALLY BUT Check valves sticking Check and clean or replace if necessary. PRESSURE LOW ON INSTALLATION Unloader valve seat faulty Check and replace if necessary.
  • Page 15: Preventative Maintenance

    HE SERIES PRESSURE WASHER OPERATOR’S MANUAL PREVENTATIVE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative mainte- nance procedures will assist in preserving the performance of your equipment.
  • Page 16: Warranty

    WHAT THIS WARRANTY COVERS All SHARK PRESSURE WASHERS are warranted by SHARK to the original purchaser to be free from defects in materials and workmanship under normal use, for the periods specified below. This Limited Warranty is subject to the exclusions shown below, is calculated from the date of the original purchase, and applies to the original components only.
  • Page 18 4275 N.W. Pacific Rim Blvd. • Camas, WA 98607 • 1-800-771-1881 Form #97-6129 • Revised 7/02 • Printed in U.S.A.

This manual is also suitable for:

He-2010He-201001dHe-201007dHe-301007dHe-301001d

Table of Contents