Page 1
MWW19-15767 / MWW00-15798 Cube Pet Fountain Fontaine pour animaux de compagnie Cube Cube drinkfontein Fuente para mascotas Cube Fontana per animali domestici Cube Trinkbrunnen – Cube PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING VEUILLEZ LIRE CE MANUEL EN ENTIER AVANT DE COMMENCER...
Page 2
Hereinafter Radio Systems Corporation, Radio Systems PetSafe Europe Ltd., Radio Systems Australia Pty Ltd. and any other affiliate or Brand of Radio Systems Corporation may be referred to collectively as “We” or “Us”. IMPORTANT SAFETY INFORMATION Explanation of Attention Words and Symbols used in this guide This is the safety alert symbol.
Page 3
• Always unplug any appliance when not in use, before putting on or taking off parts, and before cleaning. Never pull on the electrical power cord to remove the plug from the wall outlet. • Do not allow pets to chew on or swallow any parts. If you are concerned about the power cord, purchase a cord conduit (a hard plastic protector) at any hardware store.
Page 4
Thank you for choosing the Aqua Fountain by PetSafe Brand. You and ® your pet deserve a companionship that includes memorable moments and a shared understanding together. Our products and training tools enhance the relationship between pets and their owners. If you have any questions about our products or training your pet, please visit our website at www.aquapetfountain.com or contact our Customer Care Centre.
Key Definitions Bowl: The Bowl is the foundation of the Pet Fountain. It features a “Cord Channel” to hide the electrical power cord from view. Housing: Water is pumped up through the Housing to cycle through the Charcoal Filter and out the spout to create a waterfall into the Bowl. Housing Lid: The Housing Lid snaps in place over the Housing, keeping pets out of the Charcoal Filter.
Page 7
4. Remove the Housing by squeezing the Bowl just Fig. 2 beneath the locking tabs at the back (Fig. 2) and lift up on the Housing. 5. Turn Housing over and insert the Foam Filter on the side of the Housing with the water grate (Fig. 3).
Pet Fountain Disassembly and Cleaning • Pet Fountain must be cleaned to continue working normally. • Never wash the filters with soapy water, as the soap residue will seep into the filters and cannot be removed. Only rinse the filters with water. FILTER SYSTEM The Pet Fountain is equipped with two types of filters that should be replaced on a regular basis.
Page 9
PET FOUNTAIN: Clean the Pet Fountain once a week. Unplug the Pet Fountain and disconnect Fig. 6 the In-Line Plug (Fig. 6). 2. Remove the Housing Lid and remove the Charcoal Filter. 3. Empty the water out of the Pet Fountain. 4.
9. Once the Pet Fountain is completely disassembled, you will have three plastic parts: the Lid, Housing, and Bowl. 10. Handwash the Pet Fountain plastic parts with warm water and soap. The Pet Fountain may also be cleaned with a diluted vinegar solution (20% white vinegar and 80% water).
Page 11
Remove the Pump from the Pet Fountain Fig. 11 as explained in the “Pet Fountain Disassembly and Cleaning” section. 2. Once the Pump is out of the Pet Fountain, with your thumb and forefinger, gently squeeze on either side of the Faceplate and pull it off.
Pet Fountain Reassembly Check the flow control on the Pump. Make sure it is in the desired flow rate position (Fig. 15 & 16). Fig. 15 Fig. 16 Minimum Maximum 2. Place the Pump into the Bowl between the Pump placement guides (Fig. 17). Be sure the Pump is placed with the Output Tube toward the left side, when looking at the Pet Fountain from the front (Fig.
Page 13
4. Next, feed the electrical power cord through the bottom of the Bowl until there is no slack left. Press the cord into the Cord Channel and feed through the Cord Notch on either side on back of the Bowl. Fit Rubber Gasket in place (Fig. 20). Fig.
The Pet Fountain and Your Environment If you live in a humid environment and have problems with mould or algae, soak all Pet Fountain parts in a diluted vinegar solution (20% white vinegar and 80% water) for 10 minutes after regular cleaning. Also, pour the diluted vinegar solution into the Pump’s motor cavity.
Troubleshooting The answers to these questions should help you solve most problems you may have with the Pet Fountain. If they do not, please contact our Customer Care Centre. PROBLEM SOLUTION The Pump is • Never let the water in the Bowl get below the minimum not working or fill level.
Page 16
Troubleshooting (Continued) PROBLEM SOLUTION The Pet Fountain • If you have multiple pets or dogs using the Pet Fountain, the feels slimy. slimy feeling may be caused by your pet’s saliva. Change the water and clean your Pet Fountain more frequently to prevent this.
Product and its terms can be found at www.aquapetfountain.com and/ or are available by contacting your local Customer Care Centre. Europe – Radio Systems PetSafe Europe Ltd., 2nd Floor, Elgee Building, Market Square, Dundalk, Co. Louth, Ireland Compliance This equipment complies with the EMC and Low Voltage Directives.
Terms of Use and Limitation of Liability Terms of Use Use of this Product is subject to your acceptance without modification of the terms, conditions and notices contained herein. Use of this Product implies acceptance of all such terms, conditions and notices. If you do not wish to accept these terms, conditions, and notices, please return the Product, unused, in its original packaging and at your own cost and risk to the relevant Customer Care Centre together with proof of purchase for a full refund.
Need help?
Do you have a question about the MWW19-15767 and is the answer not in the manual?
Questions and answers