Advertisement
Advertisement
Table of Contents
Related Manuals for HPA SY-P1001
Summary of Contents for HPA SY-P1001
- Page 1 Owner’s Manual SY-P1001 SY-P1002...
- Page 2 WARNING...
- Page 3 Table of Contents SY-P1001 / SY-P1002 Table of Contents Introductions ……......………………………………………….2 Features ……….......……………………………………………3 Front panel controls ..…....…………………………………..4 Rear panel controls ......………………………………………6 Connections …..…....……...……………………………………8 Block diagram ……....……………………………………… Specifications …....………………………………………….2...
-
Page 4: Unpacking And Installation
SY-P1001 / SY-P1002 Introductions Introduction SY-P1001 / SY-P1002 Welcome Congratulation and thank you for purchasing SY-P series Unpacking and Installation Although it is neither complicated to install nor difficult to operate Pre Amplifier, a few minutes of your time is required to read this manual for a properly wired installation and becoming familiar with its many features and how to use them. - Page 5 Features SY-P1001 / SY-P1002 Features * Versatile function and compact size * 6 Channels MIC input with XLR jack * 10 Channels LINE input with 1/4” phone jack * 4 Channels LINE input with RCA jack * 3 Band EQ control on every MIC channels * Acceptable wide range input level with trim pot * Useful monitoring function on the whole input and output channels with PFL/AFL switches.
-
Page 6: Front Panels
These indicators warn against clipping shortly on signal of input channel through headphone output. the each input channel. HPA recommend for users to adjust TRIM control 8. OUTPUT CHANNEL EQ CONTROLS when PEAK indicator is flickering to make best performance. - Page 7 11. CLIP INDICATORS These indicators warn against clipping shortly on the each output channel. HPA recommend for users to adjust output fader when CLIP indicator is flickering to make best performance. 12. OUTPUT LEVEL METERS These indicators show output signal level.
-
Page 8: Rear Panel
These insert jacks allow connecting external effec- tors like compressor, limiter, noise filters. 7. RECORD OUTPUT HPA would like to recommend using proper insert cable as below Pig.6 This terminal allows recording with tape recorder. 8. LINE INPUTS Tip:Output(Send to external device) - Page 9 SY-P1001 / SY-P1002 Controls Rear Panel Also allow adjusting level with TRIM pot of front panel to accept variable input sources. 9. MICROPHONE INPUTS This device allows connecting 6 balanced micro- phone input with acceptable wide impedance range from 50ohm to 600ohm.
- Page 10 SY-P1001 / SY-P1002 Connections Connections HPA products are wired to reflect accepted wiring practices used throughout the world. Balanced XLR connectors are wired as described: Pin #1 Shield Pin #2 Positive Pine #3 Negative Balanced 1/4” TRS connectors are wired as described:...
- Page 11 SY-P1001 / SY-P1002 Connections Connections CONNECTOR AND CABLE CONFIGURATIONS REMOTE DEVICE REMOTE SIDE OF CABLE DESCRIPTION CABLE (Connector Type) White(Red)/HIGH Black/LOW A. XLR** Shield/GND (XLR) Floating or Balanced low impedance: most professional equipment line in and line out, microphones. White(Red)/HIGH Black/LOW B.
- Page 12 SY-P1001 / SY-P1002 Block diagrams Connestions MICROPHONE EMERGENCY PANEL MICROPHONE POWER AMPLIFIER SY-A360 POWER AMPLIFIER POWER CASSETTE DECK CD PLAYER TUNER SPEAKERS...
-
Page 13: Block Diagrams
SY-P1001 / SY-P1002 Block diagrams... -
Page 14: Specifications
SY-P1001 / SY-P1002 Specifications Specifications Balanced Master Output 0dBm Rated Output Voltage Unbalanced Sub Output 0dBm Unbalanced Rec output -10dBm Balanced Microphone channels -60dBm Balanced Line 1-6 channels -30dBm Input sensitivity for rated Unbalanced Line 7-10 channels -30dBm output at maximum gain... - Page 15 SY-P1001 / SY-P1002...