Keep Away Tag Sensor - Garmin Delta Inbounds Owner's Manual

3
Select Add Collar.
4
Turn on the dog collar device.
The base unit searches for the device and displays a collar
ID when it is found.
5
On the base unit, press OK.
The base unit displays a message when the device is paired,
and the LED on the dog collar device flashes.
6
Press OK to complete the pairing process.

Keep Away Tag Sensor

You can use a Keep Away Tag sensor to keep your dog away
from undesired locations, such as a trash can.
NOTE: If you do not have this sensor, you can skip this section.
Installing the Battery
1
Locate the circular battery cover
Away Tag sensor.
2
Twist the cover counter-clockwise until it is loose enough to
remove.
3
Remove the cover.
4
Place the battery into the cover with the positive side facing
the inside of the cover.
NOTE: Do not damage or lose the O-ring gasket.
5 Replace the cover by aligning the dots
clockwise.
When paired with a compatible dog collar device, the Garmin
Canine app indicates when less than 1 wk. battery life remains
for the sensor.
TIP: To replace the battery, you can use a piece of tape
magnet to remove the battery from the cover.
Pairing the Sensor with Your Device
Pairing is the process of connecting an ANT+
like the Keep Away Tag sensor, with a compatible dog collar
device. Your sensor and device must be paired directly through
the Garmin Canine app on your compatible smartphone.
1
Install the battery in the sensor.
The sensor turns on.
2
Go to www.garmin.com/apps, and download the Garmin
Canine app to your smartphone.
3
Open the Garmin Canine app on your smartphone.
4 Follow the on-screen instructions to pair the sensor with your
device.
5 Bring your smartphone within 3 m (10 ft.) of the sensor and
the device.
NOTE: Stay 10 m (33 ft.) away from other sensors while
pairing.
6
Hold the sensor and dog collar device together.
Keep Away Tag Sensor
on the back of the Keep
and rotating
or a
® wireless sensor,
When the sensor and device are paired, a message appears.
7 Follow the on-screen instructions to set the range.
8
Follow the on-screen instructions to select corrective actions.
Tips for Setting the Range
You can use the Garmin Canine app to set and test the effective
range of the sensor (up to 1 m). The sensor is designed to keep
your dog away from a small, general area.
NOTE: The effective range of the sensor may vary based on
environmental conditions. You should test the range to ensure
the device and sensor perform as expected.
• After the sensor is installed, approach the sensor from
multiple directions with the dog collar device to test the
range.
• Adjust the effective range.
• For best results, select the smallest range necessary to keep
your dog out of undesired areas.
NOTE: Corrections may be inconsistent if the range is set to
a distance greater than 1 m (3 ft.).
Installing the Sensor
You can use the included adhesive mount to install the sensor in
the location your dog should avoid. For example, a trash can.
You can install multiple sensors. Go to buy.garmin.com, or
contact your Garmin dealer for information about optional
accessories.
1
Attach one side of the adhesive mount to the center of the
battery door.
2
Attach the other side of the adhesive mount to the location.
Tips for Installing the Sensor
• For consistent performance, place the sensor in a location
with an unobstructed view in all directions.
• For best results, do not place the sensor on or inside metal
objects.
For example, to avoid a metal trash can, you can install the
sensor on the wall near the trash can.
• Do not put the sensor in water.
• Do not bury the sensor.
Pairing the Remote with Your Device
Before you can use the remote with your device, you must pair
your dog collar device with the Garmin Canine app on your
smartphone.
NOTE: If you do not have this accessory, you can skip this
section.
1 From the app store on your smartphone, install and open the
Garmin Canine app.
2 From the app menu, select My Family.
3
Select a dog to pair with the remote.
4 Follow the instructions in the app to pair the remote with your
device.
After the remote is paired, it connects to your device whenever
the device is in range and turned on.
Customizing Your Device
Setting an Alert Tone
You can enable or disable tones to alert on the base unit when
your dog approaches the boundary.
Select Alert Tones > OK.
7