Advertisement
Quick Links
Warranty Period : 1 year
(from the date of your purchase)
For more details, read the attached
"Minoura Limited Warranty Policy"
card.
Please refer to our website for any
updated information.
Applicable Frame
Front Fork Width : 100mm
Hub nut, 9mm Quick release skewer,
15mm Thru axle
Rear Frame End Width :
Hub nut, 9mm Quick rekease skewer
120 / 125 / 130 / 135mm
or
12mm Thru axle (142mm width only)
Important Notes
• For standard 2-wheel bicycles only.
Due to the weight balance after removing the front
or rear wheel, any longer or heavier bikes are not
suitable for use with the RS-1700. Also, RS-1700 is
for light-duty maintenance only.
• When mounting the bike, maintain the weight balance correctly by adjusting the
main arm poisition.
In addition, be sure the heavier side of the bike is located just above one of the
tripod legs to support the weight safely.
• Use on flat and horizontal floor. Fully open the tripod legs.
• Bicycles that can be safely mounted to the RS-1700 are as follows;
Front fork width is 100mm (plain hub nut, 9mm quick skewer or 15mm thru axle types).
Rear frame end width is either 120, 125, 130 or 135mm (plain hub nut or 9mm quick skewer type) or 142mm (12mm thru
axle type).
Any other specs such as narrow 74mm fork width usually found on mini-velo bikes or 20mm thru axle on Downhill bikes
cannot be mounted.
• On any bike with hydraulic disc brake, do NOT grasp the brake lever once you remove the wheel.
• When transporting RS-1700, do not just grab the top rubber part (BB Support) only. It may come off due to the stand
weight. You must hold the stand frame.
• RS-1700 supports the bike at the bottom bracket. If your bike is equipped with an electric transmission system and its
battery is located just next to the bottom bracket, it may not fit RS-1700 properly.
• RS-1700 can be used as the stand for washing bikes because of its unique swivel arm design. But you should dry the
stand as quickly as possible after using because some steel parts may rust if it stays wet.
• Use the included Velcro strap to securely hold the bike and keep it in the stand.
Contact
MINOURA JAPAN
1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Phone: +81-584-27-3131 / Fax: +81-584-27-7505
Email: minoura@minoura.jp / Web: www.minoura.jp Email: support@minourausa.com
RS-1700
If you have any questions or need help, you should contact the dealer where you purchased or the
Minoura distributor in your country first. Only when you cannot get enough service, you can contact us.
(for ALL customers)
Bicycle Maintenance Stand
MINOURA North America
California, U.S.A.
Phone: 1-510-538-8599 / Fax: 1-510-538-5899
– instructions manual
(ver.1.2 2016/12)
[ In-Use Style ]
(for U.S. residents ONLY)
Made in Japan
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for MINOURA RS-1700
Summary of Contents for MINOURA RS-1700
- Page 1 • On any bike with hydraulic disc brake, do NOT grasp the brake lever once you remove the wheel. • When transporting RS-1700, do not just grab the top rubber part (BB Support) only. It may come off due to the stand weight.
- Page 2 Schematics Each part will be called as mentioned Front Fork Mount in the right side diagram. Rear End Mount Arm Holding Knob Bolt Wheel Hook 12mm Thru Axle Adapter Arm Angle Fixing Pin Top Holding Knob Bolt Velcro Band Pillar BB Support Pillar Holding Knob Bolt Tripod Leg...
- Page 3 ① ① (Fig. C) RS-1700 is disassembled in the package to protect the surface. Assemble the stand as follows; (Fig. B) ① Fully open the tripod legs and place it on the flat and horizontal floor.
- Page 4 Front Fork Mount & Rear End Mount The quick release skewer on the Front Fork The Front Fork Mount and the Rear End Mount will be installed Mount is a specially designed wide stroke type. Usually you need to loosen the skewer nut to to to the Arm by screwing the remove the front wheel due to the projection on knob bolt to the plate nut in the...
- Page 5 Mounting Your Bike Onto RS-1700 Loosen the Top Holding Knob Bolt to allow to swivel the top arm section. (see Fig. I) Do not loosen the lower Pillar Holding Knob Bolt. The pillar and the top part will drop down.
- Page 6 In case of 12mm thru axle, align the frame end hole to the Rear End Mount hole, then insert the 12mm skewer to hold. (see Fig. L) (Fig. L) Hold the bike to the arm secreuly with the supplied Velcro tape. Holding With Front Fork Holding With Frame Rear End (Fig.
- Page 7 This provides easy access to both sides of the bike from one position. The RS-1700 also makes a great stand to wash your bike. The stand may loose balance when rotating due to the worse weight ballance, especially the arm comes between the tripod legs.
Need help?
Do you have a question about the RS-1700 and is the answer not in the manual?
Questions and answers