Table of Contents
Advertisement
Wiring and Accessories
Power Supply
Fuse
R
S
T
PD
P
Inverter
RB
N
U
V
W
IM
Motor
Stöwer Antriebstechnik GmbH, Enneststrasse 3, 51702 Bergneustadt, tel: 02261-40970, Fax: 02261-41309
Motor Output
Input
kW
HP
Voltage
VT
CT
VT
CT
0.2
0.1
1/4
1/8
0.4
0.2
1/2
1/4
1-phase
0.55
0.4
3/4
1/2
200V
1.1
0.75
1.5
1
2.2
1.5
3
2
3.0
2.2
4
3
0.2
0.1
1/4
1/8
0.4
0.2
1/2
1/4
0.75
0.4
1
1/2
1.1
0.75
1.5
1
2.2
1.5
3
2
3-phase
3.0
2.2
4
3
200V
5.5
3.7
7.5
5
7.5
5.5
10
7.5
11
7.5
15
10
15
11
20
15
18.5
15
25
20
0.75
0.4
1
1/2
1.5
0.75
2
1
2.2
1.5
3
2
3.0
2.2
4
3
4.0
3.0
5
4
3-phase
400V
5.5
4.0
7.5
5
7.5
5.5
10
7.5
11
7.5
15
10
15
11
20
15
18.5
15
25
20
Note 1: Field wiring must be made by a UL-Listed and CSA-certified closed-loop terminal connector sized for the wire gauge involved.
Connector must be fixed by using the crimping tool specified by the connector manufacturer.
Note 2: Be sure to consider the capacity of the circuit breaker to be used.
Note 3: Be sure to use a larger wire gauge if power line length exceeds 66ft. (20 m).
Note 4: Use 18 AWG / 0.75mm
2
wire for the alarm signal wire ([AL0], [AL1], [AL2] terminals).
Name
Input-side AC Reactor
EMC filter
(for CE applications, see Appendix D)
Radio noise filter
Radio noise filter
(use in non-CE applications)
DC link choke
Braking register
Braking unit
Output side nose filter
Radio noise filter
Output-side AC Reactor
LCR filter
Wiring
Inverter
Model
Power Lines
WJ200-001SF
WJ200-002SF
AWG16 / 1.3mm
(75
°
C only)
2
WJ200-004SF
°
WJ200-007SF
AWG12 / 3.3mm
2
(75
C only)
WJ200-015SF
AWG10 / 5.3mm
2
WJ200-022SF
WJ200-001LF
WJ200-002LF
AWG16 / 1.3mm
2
WJ200-004LF
WJ200-007LF
°
WJ200-015LF
AWG14 / 2.1mm
(75
C only)
2
°
WJ200-022LF
AWG12 / 3.3mm
(75
C only)
2
°
WJ200-037LF
AWG10 / 5.3mm
(75
C only)
2
WJ200-055LF
°
AWG6 / 13mm
(75
C only)
2
WJ200-075LF
°
WJ200-110LF
AWG4 / 21mm
2
(75
C only)
°
WJ200-150LF
AWG2 / 34mm
(75
C only)
2
WJ200-004HF
WJ200-007HF
AWG16 / 1.3mm
2
WJ200-015HF
WJ200-022HF
AWG14 / 2.1mm
2
WJ200-030HF
°
WJ200-040HF
AWG12 / 3.3mm
(75
C only)
2
WJ200-055HF
°
AWG10 / 5.3mm
2
(75
C only)
WJ200-075HF
°
WJ200-110HF
AWG6 / 13mm
(75
C only)
2
WJ200-150HF
AWG6 / 13mm
(75
°
C only)
2
Function
This is useful in suppressing harmonics induced on the power supply lines and
for improving the power factor.
WARNING: Some applications must use an input-side AC Reactor to prevent
inverter damage. See Warning on next page.
Reduces the conducted noise on the power supply wiring between the inverter
and the power distribution system. Connect to the inverter primary (input) side.
Electrical noise interference may occur on nearby equipment such as a radio
receiver. This magnetic choke filter helps reduce radiated noise (can also be used
on output).
This capacitive filter reduces radiated noise from the main power wires in the
inverter (input) side.
Suppress harmonics generated by the inverter. However, it will not protect the
input diode bridge rectifier.
This is useful for increasing the inverter's control torque for high duty-cycle (on-
off) applications, and improving the decelerating capability.
Reduces radiated noise from wiring in the inverter output side.
Electrical noise interference may occur on nearby equipment such as a radio
receiver. This magnetic choke filter helps reduce radiated noise (can also be used
on input).
This reactor reduces the vibration in the motor caused by the inverter's switching
waveforms, by smoothing the waveform to approximate commercial power
quality. It is also useful to reduce harmonics when wiring from the inverter to
the motor is more than 10 m in length.
Sine wave shaping filter for output side.
Fuse
(UL-rated,
Signal Lines
class J, 600V)
10A
20A
30A
10A
15A
20A
18 to 28 AWG /
30A
0.14 to 0.75 mm
2
shielded wire
60A
(see Note 4)
80A
10A
15A
30A
50A
25
Hide quick links:
Advertisement
Table of Contents
