Hitachi WJ200-001SF Manual page 11

Code Function Name
A019 Multi-speed operation selection
A020 Multi-speed 0 setting
A220 Multi-speed 0 setting, 2nd motor
A021
l Multi-speed 1 – 15 setting
A035
A038 Jog frequency setting
A039 Jog stop mode
A041 Torque boost select
A241 Torque boost select, 2nd motor
A042 Manual torque boost value
A242 Manual torque boost value, 2nd motor
A043
Manual torque boost frequency adjustment
A243 Manual torque boost frequency adjustment, 2nd motor
A044 V / f characteristic curve selection
A244 V / f characteristic curve selection, 2nd motor
A045 V / f gain setting
A245 V / f gain setting, 2nd motor
A046
Voltage compensation gain for automatic torque boost
Voltage compensation gain for automatic torque boost,
A246
2nd motor
A047 Slip compensation gain for automatic torque boost
S lip c o m p e n s a t i o n g ai n f o r a u t o m a t i c t o r q u e b o o s t ,
A247
2nd motor
A051 DC braking enable
A052 DC braking frequency setting
A053
DC braking wait time
A054 DC braking force for deceleration
A055
DC braking time for deceleration
A056 DC braking / edge or level detection for [DB] input
A057
DC braking force at start
A058 DC braking time at start
A059 Carrier frequency during DC braking
A061 Frequency upper limit setting
A261 Frequency upper limit setting, 2nd motor
A062 Frequency lower limit setting
A262
Frequency lower limit setting, 2nd motor
A063 Jump (center) frequency setting 1
A064 Jump (hysteresis) frequency width setting 1
A065 Jump (center) frequency setting 2
A066 Jump (hysteresis) frequency width setting 2
A067 Jump (center) frequency setting 3
A068
Jump (hysteresis) frequency width setting 3
A069 Acceleration stop frequency setting
A070 Acceleration stop time setting
A071 PID enable
A072 PID proportional gain
A073 PID integral time constant
A074
PID derivative time constant
A075 PV scale conversion
A076 PV source setting
A077 Reverse PID action
A078
PID output limit
A079 PID feed forward selection
A081 AVR function select
A281 AVR function select, 2nd motor
A082
AVR voltage select
A282 AVR voltage select, 2nd motor
A083
AVR filter time constant
A084 AVR deceleration gain
Stöwer Antriebstechnik GmbH, Enneststrasse 3, 51702 Bergneustadt, tel: 02261-40970, Fax: 02261-41309
Setting Range
00 (Binary mode) / 01 (Bit mode)
0.00 / "start frequency" to "maximum frequency (1st)" [Hz]
0.00 / "start frequency" to "maximum frequency (2nd)" [Hz]
0.00 / "start frequency" to "maximum frequency" [Hz]
"start frequency" to 9.99 [Hz]
00 (Free-run stop [invalid during run]) /
01 (Controlled deceleration [invalid during run]) /
02 (DC braking to stop [invalid during run]) /
03 (Free-run stop [valid during run])
04 (Controlled deceleration [valid during run])
05 (DC braking to stop [valid during run])
00 (manual torque boost) /
01 (automatic torque boost)
0.0 to 20.0 [%]
0.0 to 20.0 [%]
0.0 to 50.0 [%]
0.0 to 50.0 [%]
00 (VC) / 01 (VP) / 02 (free V / f) / 03 (SLV)
00 (VC) / 01 (VP) / 02 (free V / f) / 03 (SLV)
20 to 100 [%]
20 to 100 [%]
0 to 255
0 to 255
0 to 255
0 to 255
00 (disabled) / 01 (enabled) / 02 (output freq < [A052])
0.00 to 60.00 [Hz]
0.0 to 5.0 [s]
0 to 100 / 70 [%] (CT / VT)
0.0 to 60.0 [s]
00 (edge operation) / 01 (level operation)
0 to 100 / 70 [%] (CT / VT)
0.0 to 60.0 [s]
2.0 to 15.0 / 10.0 [kHz] (CT / VT)
0.00 / A062 to A004 [Hz]
0.00 / A262 to A204 [Hz]
0.00 / b082 to A061 [Hz]
0.00 / b082 to A261 [Hz]
0.00 to 99.99 / 100.0 to 400.0 [Hz]
0.00 to 10.00 [Hz]
0.00 to 99.99 / 100.0 to 400.0 [Hz]
0.00 to 10.00 [Hz]
0.00 to 99.99 / 100.0 to 400.0 [Hz]
0.00 to 10.00 [Hz]
0.00 to 99.99 / 100.0 to 400.0 [Hz]
0.0 to 60.0 [s]
00 (disabled) / 01 (enabled) / 02 (enabled inverted-data output)
0.00 to 25.00
0.0 to 999.9 / 1000. to 3600. [s]
0.00 to 99.99 / 100.0 [s]
0.01 to 99.99
00 (input via OI) / 01 (input via O) / 02 (external communication) /
03 (pulse train frequency input) / 10 (operation result output)
00 (OFF) / 01 (ON)
0.0 to 100.0 [%]
00 (disabled) / 01 (O input) / 02 (OI input)
00 (always on) / 01 (always off) / 02 (off during deceleration)
00 (always on) / 01 (always off) / 02 (off during deceleration)
200 V class : 200 / 215 / 220 / 230 / 240 (V)
400 V class : 380 / 400 / 415 / 440 / 460 / 480 (V)
200 V class : 200 / 215 / 220 / 230 / 240 (V)
400 V class : 380 / 400 / 415 / 440 / 460 / 480 (V)
0.000 to 9.999 / 10.00 [s]
50 to 200 [%]
[ ○ = Allowed × = Not parmitted]
Setting During Change During
Default
Operation Operation
Setting
(allowed or not) (allowed or not)
× × 00
0.00
○ ○
0.00
○ ○
0.00
○ ○
6.00
○ ○
× 04
○
× × 00
× × 00
1.0
○ ○
1.0
○ ○
5.0
○ ○
5.0
○ ○
× × 00
× × 00
100
○ ○
100
○ ○
100
○ ○
100
○ ○
100
○ ○
100
○ ○
× 00
○
× 0.50
○
× 0.0
○
× 50
○
× 0.5
○
× 01
○
× 0
○
× 0.0
○
× 5.0
○
× 0.00
○
× 0.00
○
× 0.00
○
× 0.00
○
× 0.00
○
× 0.50
○
× 0.00
○
× 0.50
○
× 0.00
○
× 0.50
○
× 0.00
○
× 0.0
○
× 00
○
1.00
○ ○
1.0
○ ○
0.00
○ ○
× 1.00
○
× 00
○
× 00
○
× 0.0
○
× 00
○
× × 02
× × 02
× × 200 / 400
× × 200 / 400
× 0.300
○
× 100
○
13